Rhondda Cynon Taff · Wales
Bath re-enamelling & resurfacing in Bryncae, Rhondda Cynon Taff
Bath re-enamelling for Bryncae, without a refit. Get a fixed price from your pictures, then we come to you.
- Resurfacing from £350
- An original cast iron bath that needs restoring
- Thin, worn enamel in places
What we are called out for in Bryncae
Older baths often have several problems at once: dull areas, chips, rust and staining. Re-enamelling deals with all of them in one go.
Signs it’s time to call us include:
- An old resurfacing that’s failing
- Stains that won’t shift
- Lots of chips and rust spots
- An outdated colour you’d like to change
What to look for in a quote
- Who turns up on the day
- Whether the colour is mixed to match
- A fixed price, and whether VAT is included
- What happens if they find more damage
Bath re-enamelling at your home in Bryncae
The bath stays where it is, so your taps, tiles and plumbing are left alone. Most baths are done in one visit, and can be used again the next day. We work on pressed steel baths, acrylic baths and basins & shower trays, and common reasons people contact us are chips and rust in more than one place and a dull, rough surface that won’t come clean.
All our work is covered by a one-year guarantee, wherever you are in Rhondda Cynon Taff.
- Location
- Bryncae (CF72, CF35)
- Region
- Rhondda Cynon Taff
- Cover
- A year, on every repair
- Quotes
- From £350. Free and fixed, from your pictures
- Telephone
- 0345 017 0787
- Updated
- 23 October 2026
What else we do in Bryncae
DIY repairs versus a professional job
For a hairline mark somewhere you will never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, a professional repair is worth it.
If you do try a kit, read the instructions carefully and work on a clean, dry surface, and don’t use it until it has fully cured. If it fails, we can still put it right.
Prices and what affects them
Resurfacing from £350. Prices are worked out job by job. What matters most is:
- Whether old repairs or coatings need taking off
- How hard the colour is to match
- The material
- What kind of damage it is
The price depends on the type and amount of damage, the material and how many items we do on one visit. You get a fixed quote from your photos, so there are no surprises on the day.
How to get a fixed price
Two or three clear photos are normally enough. It helps if you send:
- A coin or ruler next to the damage for scale
- Good light, ideally daylight, without flash glare
- One picture of the entire bath
- A close-up of the damage, in focus
A quote takes minutes to ask for: take one close-up and one wider shot of the bath, include your postcode and send them over. What comes back is a fixed price, not a guess.
Bryncae questions
How long does re-enamelling last?
Look after it and it lasts. Gentle cleaning, no suction mats.
What happens next?
We check the damage, the material and your postcode, then reply with a quote and the next dates we have.
I’m a tenant. Can you help?
Of course. Ask your landlord first, and we can send them the quote if that helps.
Can you resurface a pink bath in white?
Yes, white is the usual choice. Tell us what you’d like when you ask for a quote.
Will there be fumes?
Some odour is normal while we spray, so we ventilate the room. It clears as the finish cures.
What areas do you cover?
Everywhere in the UK, Bryncae included. Travel is included in the price.
Do I have to be there?
We need someone to let us in. You don’t need to watch us work.
What if the damage is worse than the pictures show?
Your quote covers the damage in the pictures. If there’s more, we’ll tell you before starting.
Materials and what they mean for the repair
Acrylic
Acrylic is light and warm to the touch, but it needs firm support underneath. Repairs to cracks are reinforced from the back.
Pressed steel
Under the enamel of a steel bath is thin metal. Exposed steel rusts quickly, so we treat and seal the metal before filling.
What happens on the day
A typical visit goes like this: we arrive at the agreed slot, sheet and mask the area around the job, carry out the work and clear up. Plan for most of the day. Before leaving, we tell you when it can be used and how to look after it.
- We mask and protect the room and ventilate it.
- The bath is cleaned, degreased and any chips or rust repaired.
- The surface is prepared and a bonding primer applied.
- We spray on the new enamel finish in several coats.
- Once cured, normally by the next day, the bath is ready.
Preparing for the visit
- Clear toiletries, mats and anything else from around the area
- Have somewhere for us to park nearby if possible
- Let us know which floor the room is on
Getting a price
Most customers in Bryncae get their price from photos. Add a line about what happened and your postcode, and we’ll reply with a fixed quote and the earliest dates we have.
Related advice
When we would advise against a repair
In fairness, some problems need a different fix:
- A metal bath with a through crack
- Holes rusted through the metal
- A poorly supported acrylic bath, until it’s firmed up
Not sure? Send photos and we will give you a straight answer.
Materials we repair
- Acrylic baths
- Pressed steel baths
- Cast iron baths
- Basins & shower trays
- Victorian roll-tops
How to care for the repair
Once the work has cured, treat it gently:
- Do not leave bottles, razors or sponges standing on the surface
- A dripping tap should be fixed promptly
- Do not use the bath until it has fully cured
- A quick wipe after use keeps limescale away
Wipe the bath dry after use where you can, especially in hard water areas, and rinse away any product left on the surface.
Do not try to scrub a worn bath back to shine. It removes more of the surface and makes resurfacing more work.
Landlords, agents and businesses in Bryncae
Hotels, guest houses and holiday lets can’t afford rooms out of action for long, so we keep visits short and tidy. We can work around your bookings.
We regularly price jobs from inventory or check-out photos. You can have a price before you arrange access, and we liaise with tenants about access if you’d like us to.
Bryncae and the surrounding area
Bryncae is about 5 miles east of Bridgend, in Rhondda Cynon Taff. Clients in Bryncae get the same service as everywhere else we cover: a fixed quote from pictures, and a technician at your door on the day. We cover all 133 towns and villages across Rhondda Cynon Taff.
Jobs in CF72 and CF35 are booked in the same way as anywhere else. That includes homes on South View, Ffordd Dol y Coed and Bridgend Road and the roads around them. Bryncae is on the A473, which makes it straightforward to reach. Nearby, we also work in Brynna (1 mile north-west), Dolau (1 mile east), Llanharan (1 mile north-east), Brynnau Gwynion (1 mile west) and Penprysg (2 miles west). Further out, we also cover Aberdare (13 miles north), Pontypridd (7 miles north-east), Mountain Ash (11 miles north), Tonypandy (6 miles north), Rhondda (8 miles north) and Porth (6 miles north).
Local landmarks in Bryncae
Our clients here include homes close to Brynnau Primary School, Bryncae Arms and Pencoed Comprehensive School. The nearest railway station is Llanharan station, roughly 0.7 miles north-east of the centre. Well-known places in the area include Royal Mint Museum (3.3 miles north-east) and Royal Glamorgan Hospital (2.9 miles east). Not far away are Nant Dyfrgi Pool and Bryn.
About our accreditations · Every repair comes with a one-year guarantee.
