Lincolnshire · England
Bath Re-enamelling for Burton Waters homes
Bath re-enamelling for Burton Waters, without a refit. Get a fixed price from your pictures, then book a visit.
- Resurfacing from £350
- Thin, worn enamel in places
- A bath in a colour that no longer suits
Bath re-enamelling at your home in Burton Waters
We resurface cast iron, steel and acrylic baths, including roll-tops and period baths. The finish is sprayed on in several coats over a bonding primer, after the bath has been cleaned, repaired and keyed. Whether it’s a bath that stays dull however much you clean it and a period or roll-top bath worth keeping, we can usually put it right, on cast iron baths, pressed steel baths and basins & shower trays alike.
You are covered for a year from the day of the repair. If anything isn’t right, ring us and we will come back.
- Area
- Burton Waters (LN1)
- Area hub
- Lincolnshire
- Warranty
- One year on every repair
- Price
- From £350. Free and fixed, from your pictures
- Telephone
- 0345 017 0787
- Page updated
- 23 October 2026
How we price bath re-enamelling
Prices start from £350. Quotes are free and the price is fixed. What we look at:
- What kind of damage it is
- Unusual colours or finishes
- Whether we combine several jobs
- What the surface is made of
Compared with replacing, a repair is typically a fraction of the price, because nothing has to be taken out, refitted or made good. The quote lists exactly what you’re paying for.
Getting a price from photos
Phone pictures are fine. Make sure they show:
- Your postcode, so we can check dates
- The material, if you know it
- A coin or ruler next to the damage for scale
- Good light, ideally daylight, without flash glare
There’s no need for us to visit first. Nearly every job can be priced from pictures: send a close-up, a wider shot and your postcode, and we’ll come back to you with a fixed figure.
Questions from Burton Waters
Is it OK to have pets in the house?
On the day, the room should be kept clear of pets and children, mainly so nothing gets touched before it has cured.
Does someone need to be in?
Someone needs to let us in and show us the job. You do not need to watch us work.
I rent my home. Can I book you?
We can work for tenants, landlords or agents. Just ensure the landlord agrees.
Is there a smell?
Yes, while we’re applying the finish. Ventilation keeps it down, and it fades as the finish cures.
What areas do you cover?
Across the UK, and that includes Burton Waters. Prices don’t change with location.
What does bath re-enamelling cost?
Prices start from £350. The exact price depends on the damage, so we quote from pictures. You’ll get a fixed figure before booking.
Is there a guarantee?
All our work carries a one-year guarantee. Ask us what it covers when you get your quote.
What happens next?
You will get a fixed quote back, plus dates. You are under no obligation.
Repairs by material
Pressed steel
Steel baths re-enamel well, as long as any rust is dealt with first. Steel frequently rusts by the plughole, so we check it carefully.
Acrylic
We resurface acrylic baths as well, with a coating system suited to acrylic. The bath needs to be firm and well supported for the finish to last.
Why repair rather than replace?
Replacing a bath can take several days across several trades. Re-enamelling is one technician, usually one day, and the bath is usable the day after. Prices start from £350. Rather than charging by the hour, we fix the price before we start. Damage, material and access decide it.
What you get with us
- Same prices wherever you are
- CHAS, Constructionline and SafeContractor accredited
- Nothing taken out or refitted
- A fixed quote before booking
Read our prices page and bath cost comparison.
Also near Burton Waters
What else we do in Burton Waters
DIY repairs versus a professional job
It’s natural to want to try a repair yourself. The risk is that a kit repair hides the damage for a while, then fails, and then the old filler has to be removed first.
You can buy a DIY kit for most repairs, and they can make a small mark look better. Where they fall down is colour and preparation: they come in a handful of shades, and if the surface isn’t prepared the repair will not last.
When we’d advise against a repair
To be straight with you, some problems need a different fix:
- A bath split right through the body
- Anything hidden under an old coating, until we remove it
- Leaking taps or wastes (a plumber’s job)
Send us pictures and we will tell you honestly before booking.
Materials we repair
- Victorian roll-tops
- Pressed steel baths
- Acrylic baths
- Cast iron baths
- Basins & shower trays
The process
On the day, the technician arrives at the agreed time, protects the room with dust sheets and masking and gets started. Expect it to take a full day. We tidy up before we leave and let you know when you can use it again.
- First we protect the bathroom and set up ventilation.
- Next we degrease the bath and fix chips and rust spots.
- We key the surface and put on a bonding primer.
- We spray on the new enamel finish in several coats.
- We leave it to cure, and it’s usually ready the day after.
Getting ready for the visit
- Avoid using the area for a few hours before we arrive
- Tell us if there are stairs or a lift
- Mention any parking restrictions or tricky access
Ask for a price
The quickest way to a price is to send two or three photos through our quote form or ring us. We’ll say right away if a repair is the right fix.
Related advice
Common problems we fix in Burton Waters
Sometimes it’s an earlier resurfacing that has failed, lifting by the plughole or blistering. Failing coatings are stripped back before we resurface.
The things customers typically mention when they call include:
- A dull, rough surface that will not come clean
- Thin, worn enamel in places
- Chips and rust in more than one place
- Brown or grey marks that don’t clean off
Questions to ask before booking
- Whether there are any call-out or travel charges
- What happens if the damage is worse than the photos show
- What aftercare is recommended
- When it can be used again
Our work in Burton Waters
Burton Waters is about 3 miles north-west of Lincoln, in Lincolnshire. We agree a date that works for you, and you will know when to expect us, so you are not left waiting in all day. Burton Waters is one of 732 towns and villages in Lincolnshire we cover. We work right across the region, from Burton Waters to Leeds (55 miles away).
Every address in LN1 is covered, from the main roads to the quietest streets. That includes homes on The Landings, Marine Walk and The Quays and the roads around them. Neighbouring places we cover include Burton-by-Lincoln (2 miles north-east), South Carlton (2 miles north-east), Ermine West (2 miles east), Ermine (2 miles east) and New Boultham (3 miles south-east). We also work in nearby towns such as Lincoln (3 miles south-east), Gainsborough (13 miles north-west), North Hykeham (4 miles south), Hykeham (5 miles south), Waddington (6 miles south-east) and Bracebridge Heath (5 miles south-east).
Landmarks near Burton Waters
We visit homes around Church of St Lawrence, Lincoln Castle Academy and St Lawrence Church of England Primary School and the streets around them. Burton Waters’s nearest station is Lincoln Central station, about 2.9 miles south-east of the centre. Nearby you will also find St John's Hospital (4.5 miles south-east) and Lincoln Castle (2.5 miles south-east). The countryside around Burton Waters includes Brayford Pool.
For landlords and businesses
Rental properties take more wear, and replacing things at every changeover adds up. A repair between tenancies is a cheaper way to keep the property in good order.
For developers and builders, we fix damage before handover. We can visit several plots in one trip.
About our accreditations · Every repair comes with a one-year guarantee.
