Norfolk · England
Bath re-enamelling & resurfacing in Colby, Norfolk
Full bath re-enamelling and resurfacing for householders, landlords and businesses in Colby. Free, fixed quotes from your photos.
- Resurfacing from £350
- An original cast iron bath that needs restoring
- Worn patches where water runs and sits
DIY kit or professional repair?
A DIY attempt is not a disaster. We remove the old filler and start again, so it does not stop a professional repair. It does add a little time, so tell us about it when you send pictures.
We understand the appeal of fixing it yourself. The risk is that a kit repair hides the damage for a while, then fails, and the old filler has to come out before a proper repair.
Bath re-enamelling in Colby without replacing anything
Re-enamelling is a one-day job for most baths. Nothing is disconnected or removed. We’re frequently asked to fix a coating lifting around the plughole and staining under the taps and around the waste, across pressed steel baths, acrylic baths and Victorian roll-tops.
Big or small, you get the same one-year guarantee.
- Where
- Colby (NR11)
- County
- Norfolk
- Warranty
- 12 months on all our work
- Price
- From £350. Fixed and free, based on pictures
- Telephone
- 0345 017 0787
- Page updated
- 23 October 2026
Repairing versus replacing in Colby
Replacing a bath generally involves a plumber, a fitter and a tiler. Re-enamelling takes one technician and normally one day, with the bath ready the next day. Prices start from £350. Compared with replacing, repairing typically costs far less, because nothing has to be taken out, refitted or made good. Your fixed quote shows exactly what’s included.
Why book with us
- Everything repaired in place
- Honest advice, even when it means no job
- Most jobs done in one visit
- One-year guarantee on every repair
Take a look at our prices page and bath cost comparison.
Your questions about bath re-enamelling in Colby
Do you need to take the bath out?
No, it stays where it is. Everything is done in your bathroom, with the room protected and ventilated.
Do I have to be there?
Yes. We need access to the room while we work, at a time that suits you.
Is a repair better than a new one?
Usually, when the rest is in good condition. Repairing avoids the cost and disruption of replacing. We’ll tell you honestly if replacement makes more sense.
Will you leave a mess?
We protect the room with dust sheets and masking first, and tidy up before we leave.
Do you hold any accreditations?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
When can you do it?
Your quote comes with available dates. Tell us if you need it done quickly.
Which areas do you work in?
Across the UK, and that includes Colby. Prices don’t change with location.
How long does re-enamelling last?
Look after it and it lasts. Avoid abrasive cleaners and suction mats.
About Colby
Colby is about 4 miles west of North Walsham, in Norfolk. We visit homes and businesses in Colby and the surrounding area, so you don’t need to take anything anywhere. Our repair technicians cover all 797 towns and villages in Norfolk.
All of NR11 is within our area. Neighbouring places we cover include Alby (1 mile north-west), Erpingham (2 miles west), Town Green (2 miles north-west), Ingworth (2 miles south-west) and Calthorpe (2 miles west). Within a short drive, we also cover Norwich (14 miles south), Sprowston (12 miles south), Thorpe St Andrew (14 miles south), North Walsham (4 miles east), Sheringham (8 miles north-west) and Norwich Lanes (14 miles south).
Near you in Colby
Around Colby, we work in homes near Church of St Giles and the streets around them. The closest station to Colby is Gunton station, about 3 miles north-east of the centre. Further afield, we also cover the area around Burgh next Aylsham (3.4 miles south) and Norfolk Museum of Straw Works (0.8 miles north).
Landlord and trade work in Colby
We carry out planned and one-off repairs for housing associations and facilities teams. A repair avoids taking out and refitting, which matters when someone is living in the home.
Builders use us to fix snagging damage before handover, saving last-minute replacements. Several plots can be done in one visit.
Nearby places to Colby
What else we do in Colby
The process
We work cleanly and quietly, so you can stay at home while we are there. We protect the area first, then the work takes most of the day. Before we leave, we explain the curing time and the aftercare.
- We check the bath and agree the finish with you.
- Everything around the bath is masked and covered.
- We degrease the bath, fix any damage and key the surface.
- We apply the primer and then the finish coats.
- The masking comes off, we tidy up and tell you when it can be used.
Preparing for the visit
- Let us know which floor the room is on
- Clear toiletries, mats and anything else from around the area
- Mention any parking restrictions or tricky access
Ask for a price
For most jobs, photos are all we need to give you a price. Add a line about what happened and your postcode, and we will send back a fixed quote and some dates.
Advice
Keeping it looking good
Simple care helps the repair last. Our advice:
- Use washing-up liquid and a soft cloth
- Store bottles off the bath
- Avoid suction-cup mats
- Have chips seen to early
Treat the new finish gently at first: give it the full curing time, then clean it gently. After that, no abrasives and no suction mats.
Rust spots on a worn bath get worse with time. Resurfacing before they spread keeps it simpler.
When we’d advise against a repair
It helps to know what we can’t do too:
- A cast iron or steel bath that’s cracked right through
- Damage hidden under a previous coating, until it’s stripped back
- Leaks from fittings rather than the bath
Send us pictures and we’ll tell you honestly.
Materials we repair
- Acrylic baths
- Basins & shower trays
- Pressed steel baths
- Cast iron baths
- Victorian roll-tops
When to call us in Colby
Often the bath has just had decades of use, and only the surface is worn. Underneath, a cast iron or steel bath is usually as strong as ever.
Typical reasons for a call-out include:
- Staining under the taps and around the waste
- Lots of chips and rust spots
- Wear marks under the taps
- An outdated colour you’d like to change
Questions to ask before booking
- What happens if the damage is worse than the photos show
- How long it needs to cure
- How the colour is matched
- Whether cleaning and preparation are in the price
Materials and what they mean for the repair
Pressed steel
Pressed steel baths take a new finish well, once any rust has been treated. Rust around the waste is common on steel, so we pay close attention there.
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. The enamel is the part that wears or chips, and that is what we repair.
About our accreditations · Every repair comes with a one-year guarantee.
