Lincolnshire · England
Bath re-enamelling & resurfacing in Gate Burton, Lincolnshire
Damaged bath in Gate Burton? We put it right where it is, match it on site and back it with a one-year guarantee.
- Resurfacing from £350
- Staining under the taps and around the waste
- Chips and rust in more than one place
The process
The work is clean and fairly quiet, so you can stay at home while we’re there. Protection goes down first, then the work takes the best part of a day. Before we leave, we explain how soon it can be used and how to look after it.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- We repair chips, rust spots and pitting.
- The surface is keyed and primed for the new finish.
- The new finish is sprayed on in several coats and left to cure until the following day.
Getting ready for the visit
- Ensure the room can be ventilated
- Mention any parking restrictions or tricky access
- Keep pets and children out of the room while we work
Get a quote
Getting a price is easy: snap the damage close up and then the whole item, send them over with your postcode, and we’ll reply with a fixed quote. There’s no charge for the quote and you are under no obligation.
Advice
Bath re-enamelling at your home in Gate Burton
Cast iron and steel baths are ideal for re-enamelling, and acrylic baths can be resurfaced too. You end up with a smooth, glossy surface. Our technicians work on basins & shower trays, pressed steel baths and Victorian roll-tops, and people most often call us about a coloured bath you want in white and a roll-top that’s seen better days.
Peace of mind is built in: each job carries a one-year guarantee, and we will explain exactly what it covers when we quote.
- Area
- Gate Burton (DN21)
- Region
- Lincolnshire
- Cover
- 12 months on all our work
- Quote
- From £350. Free and fixed, from your pictures
- Phone
- 0345 017 0787
- Page updated
- 23 October 2026
Places near Gate Burton
Other services in Gate Burton
What we are called out for in Gate Burton
Hard water speeds up the wear, and gritty cleaners are the worst culprits.
It’s worth getting a quote if you see:
- An outdated colour you’d like to change
- Several chips and rust patches
- A peeling or bubbling previous coating
- Brown or grey marks that don’t clean off
What to look for in a quote
- How the room is protected while they work
- Whether the price covers travel
- What aftercare is recommended
- When it can be used again
Where we work around Gate Burton
Gate Burton is about 5 miles south of Gainsborough, in Lincolnshire. Wherever you are in the DN21 postcode area, a technician comes to you. Gate Burton is one of 732 places in Lincolnshire we cover. We work right across the region, from Gate Burton to Leeds (47 miles away).
We work across the DN21 postcode area. Whether you live on Willingham Road, Gainsborough Road and Littleborough Lane or a nearby road, we can come to you. We also travel to Marton (1 mile south), Knaith (1 mile north), West Burton (2 miles north), Knaith Park (2 miles north) and Cottam (2 miles south-west). We also work in nearby towns such as Lincoln (11 miles south-east), Gainsborough (5 miles north), North Hykeham (12 miles south-east), Birchwood (10 miles south-east), Hykeham (12 miles south-east) and Ermine (10 miles south-east).
What’s near Gate Burton
Typical jobs here are in homes near The Marton Academy, Ingelby Arms Public House and Church of St Helen. The nearest railway station is Gainsborough Lea Road station, about 3.7 miles north. Well-known places in the area include Rampton Secure Hospital (4.9 miles south-west).
Prices and what affects them
Prices start from £350. We do not charge extra for travel to Gate Burton. The price depends on:
- The type of damage
- How many items we do on one visit
- Any earlier repairs that need removing first
- Access to the area
The price reflects the work involved, not your postcode. The full price is agreed before you book, with no extras added later.
How to get a fixed price
Two or three clear photos are generally enough. It helps if you send:
- Your postcode, so we can check dates
- One sharp close-up of the damage
- Any earlier repairs or coatings
- A coin or ruler next to the damage for scale
We price from photos so you do not have to wait in for a survey. Send them through the quote form, or call 0345 017 0787 if you’d rather talk it through, and you will get a fixed figure back.
Landlord and trade work in Gate Burton
Hotels, guest houses and holiday lets need rooms back in use quickly, so most of our work is done in a single visit. We can work around your bookings.
We also carry out snagging repairs for builders and developers, putting right damage done during fitting. We hold CHAS, Constructionline and SafeContractor accreditations.
Repairs by material
Acrylic
Acrylic baths can be resurfaced too, using a system that bonds to acrylic. The bath needs to be firm and well supported.
Cast iron
Re-enamelling suits cast iron baths perfectly. They’re built to last, and only the surface wears, so resurfacing gives them a new life.
Honest limits
We won’t take on work that won’t last, so here’s what a repair can’t put right:
- Holes rusted through the metal
- Problems we can’t see until an old finish comes off
- A metal bath with a through crack
Not sure? Send photos and we will give you a straight answer.
Materials we repair
- Basins & shower trays
- Cast iron baths
- Victorian roll-tops
- Acrylic baths
- Pressed steel baths
Keeping it looking good
Nothing complicated is needed, just a few sensible habits:
- Keep suction mats out of the bath
- Have chips seen to early
- Respect the curing time we give you
- A dripping tap should be fixed promptly
Rinse away dyes, oils and bath bombs straight after use, as they can stain. Fix dripping taps quickly.
The longer worn enamel is left, the rougher it gets, and rust spots spread under the surface. Acting earlier keeps the preparation simpler.
Should you replace it?
Getting a cast iron bath out is hard work: they’re heavy, often need breaking up, and a new one is not cheap. Re-enamelling avoids all of it. Our bath re-enamelling starts from £350. There are no surprise extras on the day. The price we quote from your photos is the price you pay, and if the damage turns out to be different, we discuss it before starting.
Why Gate Burton customers choose us
- No need to remove anything
- One-year guarantee on every repair
- We’ll tell you if it’s not worth repairing
- Colours mixed by hand to suit your surface
See our prices page and resurfacing vs replacement cost guide.
FAQs for Gate Burton
What happens once I’ve sent pictures?
You get a fixed price and available dates. If we need another angle, we’ll ask.
What areas do you cover?
We work UK-wide, so Gate Burton is covered. Our prices are the same everywhere.
It’s been repaired before. Can you still fix it?
In most cases. The old repair comes out first.
When can you do it?
It depends on the time of year and where you are. Send photos with your postcode and we’ll reply with the earliest dates.
Can I add another job to the visit?
Yes. Doing several items on one visit usually costs less than separate visits. Include pictures of each item.
Can you fix a peeling bath coating?
Yes. Removing the old finish takes extra time, which we include in the price.
How long does re-enamelling last?
It depends on preparation, use and care. Properly prepared and looked after, it lasts well, and our work is guaranteed for a year.
Will the bath be moved?
No. We resurface it in place, so nothing else is disturbed.
About our accreditations · Every repair comes with a one-year guarantee.
