Kent · England
Bath re-enamelling & resurfacing in Newtown, Kent
Fixed-price bath re-enamelling in Newtown and the surrounding area, done in a single visit in most cases and guaranteed for a year.
- Resurfacing from £350
- A bath in a colour that no longer suits
- Chips and rust in more than one place
What affects the price in Newtown
Prices start from £350. You won’t pay by the hour. The price is based on:
- What kind of damage it is
- The colour and finish to match
- The material and finish
- Doing more than one item at once
No two jobs are quite the same, so we price each one individually. What’s damaged, how badly and how easy it is to reach all make a difference, and combining jobs on one visit brings the cost down.
Quotes from your photos
It only takes a minute to photograph the damage, and it saves a visit. Please include:
- Whether it’s been repaired or coated before
- A picture taken from further back
- The postcode, so we can plan the visit
- A close-up of the damage, in focus
Getting a price is easy: snap the damage close up and then the whole item, send them to us with your postcode, and you’ll get a fixed quote back. Quotes are free and you’re under no obligation.
About our bath re-enamelling in Newtown
We re-enamel a lot of period and roll-top baths, which are heavy, hard to move and costly to replace. Resurfacing them in place keeps the original bath. Common call-outs are for an original cast iron bath that needs restoring and a bath that stays dull however much you clean it, on pressed steel baths, basins & shower trays and cast iron baths.
We guarantee the work for a year. If there is a problem with the repair within the year, we return and sort it.
- Where
- Newtown (TN8)
- County
- Kent
- Warranty
- A year, on every repair
- Quotes
- From £350. Fixed and free, based on pictures
- Telephone
- 0345 017 0787
- Updated
- 23 October 2026
The process
We begin by going over the job with you, so you know exactly what we are doing. Then the area is sheeted and masked and we start. Allow a full day, and we will tell you if anything changes.
- We sheet, mask and ventilate the room.
- Old sealant is cut out and the bath is deep cleaned.
- We repair chips, rust spots and pitting.
- We key the bath and apply a bonding primer.
- The new finish is sprayed on in several coats and left to cure until the day after.
Preparing for the visit
- Avoid using the area for a few hours before we arrive
- Move bottles, mats and clutter away from the area
- Let us know which floor the room is on
Getting a price
You do not need a survey visit. Nearly every job can be priced from pictures: send a close-up, a wider shot and your postcode, and we will reply with a fixed price.
Advice
Your questions about bath re-enamelling in Newtown
Can you fix a peeling bath coating?
In most cases. We strip the failing coating and resurface it properly. Tell us about it when you ask for a quote.
I rent my home. Can I book you?
Of course. Check with your landlord; we can send the quote to them too.
Can you repair several things at once?
Yes. Doing several items on one visit typically costs less than separate visits. Send photos of everything you’d like done.
Are you a vetted contractor?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
What do you need from me?
Just pictures, your postcode and a contact number. On the day, we only need access to the room.
Is it worth repairing rather than replacing?
Normally, when the rest is in good condition. Repairing avoids the cost and disruption of replacing. We will tell you honestly if replacement makes more sense.
Does re-enamelling smell?
Yes, while we’re applying the finish. Ventilation keeps it down, and it fades as the finish cures.
How long does re-enamelling take?
Generally one day, with the bath ready the day after. A badly pitted bath can need a second day.
Landlord and trade work in Newtown
Hospitality businesses cannot afford rooms out of action for long, so most of our work is done in a single visit. We can work around your bookings.
We also carry out snagging repairs for builders and developers, putting right damage done during fitting so nothing needs replacing. We are CHAS, Constructionline and SafeContractor accredited.
Common problems we fix in Newtown
Older baths frequently have several problems at once: dull areas, chips, rust and staining. Re-enamelling deals with all of them in one go.
Signs it’s time to call us include:
- A roll-top that is seen better days
- Several chips and rust patches
- A dull, rough surface that won’t come clean
- A coating lifting around the plughole
Comparing quotes
- When it can be used again
- What aftercare is recommended
- What the guarantee covers, and for how long
- What preparation is included
Aftercare tips
Nothing complicated is needed, just a few sensible habits:
- Have chips seen to early
- Store bottles off the bath
- Dry the bath after use to stop limescale
- Rinse off hair dye, oils and bath bombs immediately
Stick to mild, non-abrasive cleaners, avoid suction bath mats, and keep bottles and razors off the surface.
The longer worn enamel is left, the rougher it gets, and rust spots spread under the surface. Resurfacing sooner means less repair work first.
Should I try a DIY kit first?
It’s tempting to reach for a kit, but the repairs we redo most frequently are DIY ones that have discoloured or lifted. Getting it right first time is typically cheaper.
For a hairline mark somewhere you’ll never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, it’s worth having it done properly.
Should you replace it?
Replacing the bath means a plumber, removing a heavy bath, making good the walls and tiles and several days without a working bathroom. Re-enamelling gives the bath a new finish with the bath left where it is. Our bath re-enamelling starts from £350. Set against the cost of replacement, repairing typically costs far less, because there is no removal, plumbing or making good. The quote lists exactly what you’re paying for.
What you get with us
- CHAS, Constructionline and SafeContractor accredited
- We will tell you if it’s not worth repairing
- Repair technicians who travel to you, UK-wide
- Dust sheets down, tidy finish
Read our full price list and resurfacing vs replacement cost guide.
Where we work around Newtown
Newtown is about 6 miles north-east of East Grinstead, in Kent. Our work suits any type of property, from flats and terraces to detached houses and new builds, plus businesses and rented homes. We work in all 922 towns and villages across Kent. Our jobs stretch from Newtown to London (about 24 miles away).
Postcode districts we cover here: TN8. Streets in the area include Pigdown Lane and Uckfield Lane. Neighbouring places we cover include Markbeech (1 mile south), Hever (1 mile north), Chiddingstone Hoath (1 mile south-east), How Green (2 miles north) and Walter's Green (3 miles south-east). Further out, we also cover Sevenoaks (8 miles north-east), Royal Tunbridge Wells (7 miles east), Tonbridge (7 miles east), Kings Hill (14 miles north-east), Paddock Wood (12 miles east) and Southborough (6 miles east).
Landmarks near Newtown
Typical jobs here are in homes near Hever Church of England Voluntary Aided Primary School, Chiddingstone Castle Park and Gardens and The Kentish Horse pub, among other places. The closest station to Newtown is Hever station, roughly 1 mile north-west. Well-known places in the area include Haxted Watermill Museum (3.8 miles west) and Hever Castle (1 mile north).
What we cannot put right
It helps to know what we can’t do too:
- A bath that’s rusted through
- A poorly supported acrylic bath, until it’s firmed up
- A cast iron or steel bath that’s cracked right through
If in doubt, send pictures and we will say what we think before you book.
Surfaces we repair
- Pressed steel baths
- Cast iron baths
- Basins & shower trays
- Victorian roll-tops
- Acrylic baths
Towns and villages near Newtown
What else we do in Newtown
About our accreditations · Every repair comes with a one-year guarantee.
