Isle of Wight · England
Bath Re-enamelling for Skinner's Hill homes
Bath re-enamelling across Skinner's Hill and nearby, normally in one visit and guaranteed for a year.
- Resurfacing from £350
- A bath that stays dull however much you clean it
- Brown or grey marks that do not clean off
Bath re-enamelling in Skinner's Hill, done in place
Re-enamelling gives a worn bath a new glossy surface without a refit. It’s the answer when the entire bath is tired rather than one spot. Whether it’s an outdated colour you’d like to change and enamel that’s lost its shine and feels rough, we can generally put it right, whatever the material.
Big or small, you get the same one-year guarantee.
- Area
- Skinner's Hill (PO36)
- Area hub
- Isle of Wight
- Cover
- One year on every repair
- Price
- From £350. Free and fixed, from your pictures
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
FAQs for Skinner's Hill
Can I get a quote without a visit?
In nearly every case. We only ask to see it in person if the photos can’t show what we need.
Do you work in Skinner's Hill?
Yes, we do. We send a technician to Skinner's Hill for every job, with no extra charge for travel.
Can you repair something that is been repaired before?
Generally, yes. Tell us what was done before.
Can you fix a peeling bath coating?
In most cases. We strip the failing coating and resurface it properly. Tell us about it when you ask for a quote.
How much does bath re-enamelling cost in Skinner's Hill?
Prices start from £350. We give a fixed price based on photos of the damage. Send a close-up of the damage and a wider photo with your PO36 postcode.
Do you need to take the bath out?
No. We resurface it in place, so the tiles and taps stay put.
Is a repair better than a new one?
Usually, if the item is otherwise sound. Repairing avoids the cost and disruption of replacing. We’ll tell you honestly if replacement makes more sense.
Can you re-enamel a roll-top bath?
Yes, roll-tops are a big part of our work. The inside is resurfaced, and we can refinish the outside as well.
DIY kit or professional repair?
It’s tempting to reach for a kit, but the repairs we redo most frequently are DIY ones that have discoloured or lifted. Doing it properly first is usually the cheaper route.
If you do try a kit, read the instructions carefully, and don’t use it until it has fully cured. If it does not work out, we can still repair it properly.
When a repair isn’t the answer
A few problems are outside what a surface repair can do:
- Damage hidden under a previous coating, until it’s stripped back
- A cast iron or steel bath that is cracked right through
- Leaking taps or wastes (a plumber’s job)
Send us photos and we’ll tell you honestly before you book.
What we work on
- Victorian roll-tops
- Pressed steel baths
- Cast iron baths
- Acrylic baths
- Basins & shower trays
Work for landlords and builders
We’re used to working with agents and managing companies. Just send pictures, the address and how to get access and we’ll arrange it.
If you manage property in Skinner's Hill, we can repair and quote for several addresses together. Send photos for each one and we’ll price them together.
Why repair rather than replace?
Replacing a cast iron bath is a big job: it’s very heavy, may need breaking up, and the replacement can be costly. Resurfacing in place avoids that entirely. Prices start from £350. We do not add extras on the day. What we quote from your photos is what you pay, and if the damage turns out to be different, we discuss it before starting.
Why choose Surface Doctor in Skinner's Hill
- Free fixed quotes from pictures
- Rooms protected and left tidy
- Colour mixed on the day to match
- No need to remove anything
Read our full price list or guide to resurfacing and replacement costs.
How it works
We turn up at the time we agreed with you, introduces themselves and looks over the damage before anything else. Dust sheets and masking tape go down before we open a single tin. The work itself takes a full day, and we leave the room as we found it.
- We mask and protect the room and ventilate it.
- The bath is cleaned, degreased and any chips or rust repaired.
- The surface is prepared and a bonding primer applied.
- We spray several coats of new enamel finish.
- Once cured, normally by the following day, the bath is ready.
How to prepare
- Let the surface dry out before the visit
- Open a window if you can
- Keep children and pets away from the room on the day
Getting a price
For a price in Skinner's Hill, the easiest route is pictures: one close up, one from further back, plus your postcode. We reply with a fixed quote and our next available dates.
Related advice
Places near Skinner's Hill
What else we do in Skinner's Hill
Our work in Skinner's Hill
Skinner's Hill is about 5 miles south of Ryde, in Isle of Wight. Whether you’re in the middle of Skinner's Hill or on the outskirts, the service is the same: a fixed quote, a tidy visit and a guarantee. We work in all 125 towns and villages across Isle of Wight. Our jobs stretch from Skinner's Hill to London (75 miles away).
All of PO36 is covered. From Skinner's Hill and Hill Top or anywhere nearby, we can come to you. Neighbouring places we cover include Queen's Bower (1 mile south-east), Alverstone Garden Village (1 mile north-east), Alverstone (1 mile east), Lake (2 miles south-east) and Sandown (2 miles east). Larger places within reach include Newport (5 miles north-west), Ryde (5 miles north), Cowes (8 miles north-west), Ventnor (5 miles south), East Cowes (7 miles north-west) and Oakfield (4 miles north-east). If you’re somewhere remote, ring us first and we’ll plan the trip.
Around Skinner's Hill
Locally, our jobs take us to homes close to Newchurch Primary School, Sandown Bay Academy and All Saints' Church and the streets around them. The closest station to Skinner's Hill is Sandown station, roughly 1.7 miles east of the centre. Well-known places in the area include Arthur Webster Memorial Hospital for Children (2 miles south-east) and Sandown Castle (2.3 miles east). The countryside around Skinner's Hill includes Alverstone Mead and Brading Down.
Different materials, different repairs
Acrylic
We resurface acrylic baths as well, using a system that bonds to acrylic. It must be solid and not flex underfoot.
Pressed steel
Pressed steel baths take a new finish well, as long as any rust is dealt with first. Rust around the waste is common on steel, so we check it carefully.
How to look after the repair
Looking after the surface is easy, and it makes a real difference:
- Stick to gentle, non-abrasive cleaners
- Avoid suction-cup mats
- Store bottles off the bath
- Rinse off hair dye, oils and bath bombs straight away
Rinse the bath and wipe it over after use, particularly where water is hard, to stop limescale building up.
Don’t try to scrub a worn bath back to shine. It just wears the enamel further and makes resurfacing more work.
What we are called out for in Skinner's Hill
Frequently the bath has just had decades of use, with nothing wrong except the surface. Underneath, a cast iron or steel bath is typically as strong as ever.
Keep an eye out for any of the following:
- Wear marks under the taps
- An outdated colour you’d like to change
- Brown or grey marks that don’t clean off
- Enamel that’s lost its shine and feels rough
What to look for in a quote
- What the guarantee covers, and for how long
- Whether the price covers travel
- What aftercare is recommended
- How the room is protected while they work
About our accreditations · Every repair comes with a one-year guarantee.
