Dorset · England
Bath Re-enamelling in Walton Elm
Bath re-enamelling across Walton Elm and nearby, done in a single visit in most cases.
- Resurfacing from £350
- An old resurfacing that’s failing
- An original cast iron bath that needs restoring
Bath re-enamelling at your home in Walton Elm
Re-enamelling works especially well on cast iron and steel, and we can resurface acrylic baths as well. You end up with a smooth, glossy surface. Common call-outs are for several chips and rust patches and staining under the taps and around the waste, on Victorian roll-tops, cast iron baths and basins & shower trays.
All of our repairs are guaranteed for twelve months, and the guarantee is the same wherever you live. If something goes wrong with the work, we come back.
- Location
- Walton Elm (DT10)
- Area hub
- Dorset
- Warranty
- 12 months on all our work
- Quote
- From £350. Fixed and free, based on photos
- Telephone
- 0345 017 0787
- Updated
- 23 October 2026
When to call us in Walton Elm
Often the bath has just had decades of use. The body of the bath is generally perfectly sound.
Keep an eye out for any of the following:
- A dull, rough surface that will not come clean
- Thin, worn enamel in places
- An original cast iron bath that needs restoring
- Staining under the taps and around the waste
Before booking anyone
- How the colour is matched
- How the room is protected while they work
- Whether the price is fixed and includes VAT
- What happens if the damage is worse than the photos show
Aftercare tips
How the surface is treated afterwards matters. Here’s what we suggest:
- Leave the bath for the full curing time before using it
- Keep toiletries on a shelf rather than in the bath
- Keep suction mats out of the bath
- Stick to gentle, non-abrasive cleaners
Wait for the curing time we give you before the first bath. Then, gentle cleaning with a soft cloth is enough.
Rust spots on a worn bath get worse with time, and each one adds to the preparation. It’s simpler to resurface before they spread.
Nearby places to Walton Elm
More services for Walton Elm
What we do, step by step
A typical visit goes like this: we arrive at the agreed slot, sheet and mask the area around the job, carry out the work and clear up. Allow most of the day. Before leaving, we tell you when it can be used and how to look after it.
- We mask and protect the room and ventilate it.
- The bath is cleaned, degreased and any chips or rust repaired.
- We key the surface and put on a bonding primer.
- We spray several coats of new enamel finish.
- We leave it to cure, and it’s generally ready the following day.
Getting ready for the visit
- Make sure the area is dry
- Let us know if it has been repaired before
- Clear the area around the damage
Get a quote
Send us pictures of the damage and a wider shot of the entire item, with your DT10 postcode, and we will reply with a fixed quote.
Advice
Repairs by material
Pressed steel
Pressed steel baths take a new finish well, as long as any rust is dealt with first. Rust around the waste is common on steel, so we check it carefully.
Cast iron
Cast iron baths are the classic candidate for re-enamelling. The body lasts for generations; only the enamel wears, so resurfacing gives them a new life.
Prices and what affects them
Prices start from £350. We give every job a fixed price from pictures. This is what makes a difference:
- The colour and finish to match
- The material
- How easy the damage is to reach
- How much damage there is
We do not add extras on the day. The price we quote from your pictures is the price you pay, unless the damage turns out to be different, in which case we talk to you first.
Send pictures for a quote
You can normally get a fixed price without us visiting. To make it quick:
- Something in shot to show the size
- A clear, close picture of the problem area
- Whether it’s been repaired or coated before
- Your postcode, so we can check dates
Getting a quote takes a couple of minutes: photograph the damage, then the whole bath, include your postcode and send them over. You’ll get a fixed price, not an estimate.
What a repair can’t fix
We will not take on work that will not last, so these are the limits:
- A poorly supported acrylic bath, until it’s firmed up
- Steel that has corroded right through
- Anything hidden under an old coating, until we remove it
Not sure? Send photos and we’ll give you a straight answer before booking.
Surfaces we repair
- Basins & shower trays
- Victorian roll-tops
- Pressed steel baths
- Acrylic baths
- Cast iron baths
Walton Elm and nearby
Walton Elm is about 10 miles north-west of Blandford Forum, in Dorset. Our work suits any type of property, from flats and terraces to detached houses and new builds, plus businesses and rented homes. We cover all 462 towns and villages in Dorset.
Every address in DT10 is covered. Neighbouring places we cover include Pleck (1 mile west), Marnhull (1 mile north), Hinton St Mary (1 mile south), Sturminster Newton (2 miles south) and Fifehead Magdalen (2 miles north). Within a short drive, we also cover Blandford Forum (10 miles south-east), Gillingham (6 miles north), Shaftesbury (6 miles north-east), Sherborne (9 miles west), Peacemarsh (6 miles north) and Milborne Port (6 miles west).
Local landmarks in Walton Elm
We visit homes around St Gregory's Church of England Primary School, Church of St Gregory and Sturminster Newton High School. Nearby you’ll also find Westminster Memorial Hospital (5.9 miles north-east) and Sturminster Newton Museum and Mill (2.3 miles south). Open spaces near Walton Elm include Girdlers Coppice.
Repair or replace: which is better?
If the bath is sound, re-enamelling is usually much cheaper than replacing it, once you add removal, plumbing, tiling and decorating to the price of a new bath. It’s also far quicker. Resurfacing from £350, with every job priced individually. We charge the same wherever you are, so there’s no premium for Walton Elm. The job itself decides the price: how much damage, what it’s made of and how many items.
Why choose Surface Doctor in Walton Elm
- Fixed prices from your pictures
- Work done at your home or business
- We leave the room as we found it
- Colour mixed on the day to match
Read our full price list or guide to resurfacing and replacement costs.
Walton Elm: your questions answered
Is my repair covered?
All our work carries our one-year guarantee. We’ll explain what it covers when we quote.
Is a repair better than a new one?
In most cases, yes. Replacement brings removal, refitting and making good, which a repair avoids. We’ll be honest if it’s not worth it.
Someone resurfaced my bath and it’s peeling. Can you help?
Yes, we do this regularly. Stripping the old coating adds time, so it’s reflected in the quote.
How long does re-enamelling last?
That depends on preparation and how the bath is treated. With good preparation and gentle cleaning it lasts a long time, and our work is guaranteed for a year.
What happens next?
You will get a fixed quote back, plus dates. There is no obligation to book.
How do I get a price for bath re-enamelling in Walton Elm?
Prices start from £350. Every job gets a fixed quote based on pictures of the damage. Send a close-up of the damage and a wider photo and your postcode.
Can pets and children be at home?
On the day, the room should be kept clear of pets and children, mainly so nothing gets touched before it has cured.
Can you do more than one item on the same visit?
Yes. Doing several items on one visit generally costs less than separate visits. Send photos of everything you’d like done.
DIY repairs versus a professional job
It’s natural to want to try a repair yourself. The risk is that a kit repair hides the damage for a while, then fails, and then the old filler has to be removed first.
The difference between a kit and a professional repair is mostly in the preparation and colour. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, and the work is guaranteed.
About our accreditations · Every repair comes with a one-year guarantee.
