Doncaster · England
Bath chip & crack repair in Branton, Doncaster
Bath repair across Branton and nearby, done in a single visit in most cases.
- Repairs from £95
- Rust spots around the plughole
- A hole punched through by something heavy
Can I fix it myself?
If you’ve already tried a DIY fix, that is fine. We take the old repair out and do it properly, so it does not stop a professional repair. Just mention it when you send pictures, as it can add time.
What a professional repair adds is preparation, colour matching and finishing. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, and the work is guaranteed.
How we handle bath repair in Branton
You don’t need a new bath because of a chip. We fill the damage, shape it to the curve of the bath and refinish it, with the colour mixed on site. We’re often asked to fix a chipped rim or side and snagging damage from a refit, across whirlpool & spa baths, pressed steel enamel and roll-top & freestanding.
All of our repairs are guaranteed for twelve months, and the guarantee is the same wherever you live. If something goes wrong with the work, we come back.
- Where
- Branton (DN3)
- Area hub
- Doncaster
- Guarantee
- 12 months on all our work
- Quote
- From £95. Fixed and free, based on photos
- Call
- 0345 017 0787
- Page updated
- 23 October 2026
The process
When we visit, the technician arrives at the agreed time, protects the room with dust sheets and masking and gets started. Expect it to take a few hours. We clean up when we are done and let you know when you can use it again.
- We protect the bath and the floor around it.
- We clean, key and degrease the damage.
- We fill it, let it set, then sand it flush.
- Colour and gloss are matched to the surrounding surface.
- We clear up and give you the curing time, normally until the next day.
Before we arrive
- Avoid using the area for a few hours before we arrive
- Let us know if it has been repaired before
- Point us to the nearest place to park
Getting a price
Ring 0345 017 0787, or send us photos through the quote form. With one close-up and one wider picture, we can give you a fixed price.
Related advice
Also near Branton
What else we do in Branton
FAQs for Branton
What does bath repair cost?
Repairs from £95. Every job gets a fixed quote based on pictures of the damage. Send a close-up and a picture of the whole item with your DN3 postcode.
Do I have to be there?
Yes. The technician needs access to the room for the visit, at a time that suits you.
Do you repair coloured baths?
Yes, coloured baths are no problem. The colour is tinted by hand on the day.
Is it messy?
We protect the room with dust sheets and masking first, and we clean up when we have finished.
Is there a guarantee?
Every repair comes with our one-year guarantee. We will explain what it covers when we quote.
Do you charge for travel?
There is no separate call-out charge. Your fixed quote includes everything.
What information do you need?
A close-up, a wider photo and your postcode. Then we will agree a date.
Do you work for landlords and businesses?
We do, regularly. We can quote for several properties together and work between tenancies.
Repair or replace: which is better?
Swapping a damaged bath for a new one usually means a plumber, removing the old bath, making good the tiles and panel and disposing of the old one. A repair deals only with the damage in a single visit. Our bath repair starts from £95. The price depends on the type and amount of damage, the material and how many items we do on one visit. We give a fixed quote from your photos, so there are no surprises on the day.
Why us?
- One price list for the entire UK
- Honest advice, even when it means no job
- A fixed quote before you book
- One visit for most repairs
See our pricing or resurfacing vs replacement cost guide.
Work for landlords and builders
We regularly work with letting and managing agents. Just send photos, the address and how to get access.
Builders, developers and site managers book us for snagging repairs, putting right damage done during fitting so nothing needs replacing. We are CHAS, Constructionline and SafeContractor accredited.
Our work in Branton
Branton is about 3 miles east of Doncaster, in Doncaster. Whether you’re in the middle of Branton or on the outskirts, the service is the same: fixed prices, tidy work and a one-year guarantee. Our technicians cover all 89 towns and villages in Doncaster, from the larger towns to small villages. We work right across the region, from Branton to Leeds (about 30 miles away).
Every address in DN3 is covered. Jobs here include addresses on Moor View, Rural Crescent and Valley Drive. Nearby, we also work in Old Cantley (1 mile north-west), Auckley (1 mile south-east), Cantley (1 mile west), Bessacarr (2 miles west) and Armthorpe (2 miles north). We also work in nearby towns such as Doncaster (3 miles west), Adwick le Street (8 miles north-west), Thorne (8 miles north-east), Conisbrough (8 miles west), Bentley (5 miles north-west) and New Rossington (3 miles south-west).
Near you in Branton
Typical jobs here are in homes near Branton St Wilfrid's Church of England Primary School, St Bernard's Catholic High School and The Hayfield School and the streets around them. Nearby too are Three Horseshoes pub (within half a mile south-east) and Church of St Saviour (1 mile south-east). For rail, the closest station is Kirk Sandall station, roughly 4.1 miles north-west of the centre. A little further out are Doncaster Royal Infirmary (3.4 miles north-west) and Danum Gallery (3.8 miles west). Not far away are Potteric Carr Nature Reserve.
What affects the price in Branton
Repairs from £95. We don’t charge extra for travel to Branton. The price depends on:
- How many areas need work
- How hard the colour is to match
- What kind of damage it is
- Whether we combine several jobs
There are no surprise extras on the day. What we quote from your photos is what you pay, unless the damage turns out to be different, in which case we talk to you first.
Getting a price from photos
When you take your photos, these tips help us give you a firm price:
- Whether it’s been repaired or coated before
- Any details about the material
- A close-up of the damage, in focus
- A photo taken from further back
No survey visit is needed: we price from photos. Send them through the quote form, or call 0345 017 0787 if you’d rather talk it through, and we’ll come back with a fixed figure.
Different materials, different repairs
Pressed steel
Pressed steel is thinner and lighter, with an enamel finish like cast iron. Chips rust quickly on steel, especially around the waste, so repair chips early.
Composite and resin
Stone resin and composite baths are heavy and solid, and frequently freestanding. Chips and scratches can be filled and colour-matched, in much the same way.
When a repair is not the answer
Not everything can be repaired, and we’ll tell you before we start. Repairs won’t solve:
- A whole bath that’s dull or worn, where a full re-enamel is the better fix
- Cracks in parts of an acrylic bath we cannot get to from below
- Rust that has eaten right through a steel bath
If in doubt, send photos and we’ll say what we think.
Surfaces we repair
- Pressed steel enamel
- Whirlpool & spa baths
- Roll-top & freestanding
- Acrylic
- Cast iron enamel
When to call us in Branton
The usual cause is something heavy dropped into the bath, and a lot happen during bathroom refits. Acrylic baths crack for a different reason: poor support underneath, so the bath flexes when it’s full.
Send us a picture if you notice any of these:
- Scuffs and scratches in the surface
- A kit repair that didn’t last
- Damage done while the bathroom was being fitted
- Rusty patches near the plughole
What to look for in a quote
- What the guarantee covers, and for how long
- Whether the price covers travel
- How long it needs to cure
- Who turns up on the day
About our accreditations · Every repair comes with a one-year guarantee.
