Devon · England
Bath chip & crack repair in Cove, Devon
Bath repair across Cove and nearby, done in a single visit in most cases.
- Repairs from £95
- Rust by the waste and overflow
- Cracks in an acrylic bath
Where we work around Cove
Cove is about 4 miles north of Tiverton, in Devon. Clients in Cove get the same service as everywhere else we cover: a fixed quote from your pictures, and a technician at your door on the day. Cove is one of 586 towns and villages in Devon we cover.
We work across the EX16 postcode area and the streets around it. Cove is on the A396, which makes it straightforward to reach. We also cover the places around Cove: Bampton (2 miles north), Hayne (3 miles south), Chevithorne (3 miles south-east), Bolham (3 miles south) and Huntsham (3 miles east). We also work in nearby towns such as Cullompton (9 miles south-east), Crediton (14 miles south-west), Cranbrook (15 miles south), Willand (7 miles south-east), West Clyst (15 miles south) and Uffculme (8 miles south-east).
Near you in Cove
In Cove, that means homes near Exeter Inn and the streets around them. A little further out are Huntsham Castle (2.8 miles east) and Tiverton and District Hospital (4 miles south).
How we handle bath repair in Cove
Small damage on a bath is worth repairing early. Exposed metal on enamelled baths soon rusts, and on acrylic, a crack keeps spreading while the bath flexes. Repairing it stops the damage getting worse. We regularly repair roll-top & freestanding, cast iron enamel and pressed steel enamel, and the jobs we see most are a cracked acrylic bath and damage done while the bathroom was being fitted.
A one-year guarantee comes with the work, just as it does everywhere we cover.
- Location
- Cove (EX16)
- County
- Devon
- Cover
- One year on every repair
- Quotes
- From £95. Fixed and free, based on photos
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
Looking after it afterwards
Much of the damage we repair could have been avoided. These habits help:
- Clean with warm water and a mild detergent
- Don’t leave razors or cans standing in the bath
- Make sure an acrylic bath is firm underfoot
- A dripping tap stains enamel, so fix it early
Don’t leave razors, cans or hair grips in the bath, because they can mark the enamel. And fix dripping taps promptly.
Rust under enamel spreads surprisingly quickly. A chip the size of a fingernail can become a much larger patch if it’s left for months, so early repair keeps the cost down.
Why repair rather than replace?
A new bath costs more than the bath itself: taking out the old one, plumbing, tiling, a panel and redecorating. With a repair, it’s one visit and one price. Prices start from £95. Our prices are the same across the UK, with no extra for Cove. The job itself decides the price: how much damage, what it’s made of and how many items.
Why us?
- One visit for most repairs
- One price list for the entire UK
- CHAS and Constructionline accredited
- Colour-matched on site
Take a look at our full price list or bath cost comparison.
When we’d advise against a repair
In fairness, there are a few things a repair will not fix:
- Flexing caused by a failed cradle or loose feet
- Cracks in parts of an acrylic bath we can’t get to from below
- A bath worn all over, where resurfacing makes more sense
Not sure? Send photos and we’ll give you a straight answer before booking.
Materials we repair
- Pressed steel enamel
- Cast iron enamel
- Roll-top & freestanding
- Whirlpool & spa baths
- Acrylic
Common problems we fix in Cove
Dropped items cause the majority of chips, and building work is a common culprit. Cracks in acrylic have a different cause: poor support underneath, so the bath flexes when it’s full.
The things clients generally mention when they call are:
- Rust spots around the plughole
- Chips caused by builders
- Damage beneath the taps
- A failed DIY repair that is discoloured or lifting
Comparing quotes
- How long the guarantee is and what it covers
- Who turns up on the day
- When it can be used again
- How the room is protected while they work
How we price bath repair
Prices start from £95. You’ll know the full cost before booking. We look at:
- Unusual colours or finishes
- Doing more than one item at once
- Whether it’s a chip, crack, burn or wear
- The material and finish
Most people are surprised how affordable a repair is, especially compared with replacing and refitting. Photos let us give you the exact figure.
Getting a price from pictures
Photographing the damage takes a minute, and it saves a visit. Try to send:
- Your postcode, so we can check dates
- Any details about the material
- One picture of the entire bath
- A coin beside the damage so we can judge size
Email us a picture of the damage and a wider shot of the entire item, and tell us you’re in Cove, and we will reply with a fixed quote.
How it works
Once we are through the door, we keep the work contained to the one room. We mask off everything nearby, the job takes two to three hours for most chips, depending on what we find, and we finish with a tidy-up and a look at the finished work together.
- We start by looking at the damage and confirming the plan with you.
- Any rust and loose material comes out, and the area is degreased.
- The damage is filled in layers and shaped to the curve of the bath.
- The colour is tinted by hand until it matches.
- Finally, it’s polished to match the shine and left to cure.
Getting ready for the visit
- Make sure the area is dry
- Mention any parking restrictions or tricky access
- Tell us if there are stairs or a lift
Ask for a price
Getting a price is easy: snap the damage close up and then the entire item, send them to us with your postcode, and we will reply with a fixed price. There’s no charge for the quote and you’re under no obligation.
Advice
Should I try a DIY kit first?
A kit can be fine for a tiny mark out of sight. For damage in plain view, cracks, holes or rust, or coloured finishes, a professional repair is worth it.
We understand the appeal of fixing it yourself. The trouble is that kit repairs frequently look fine at first and then fail, and then the old filler has to be removed first.
Also in Cove
Questions from Cove
Can you repair a failed DIY repair?
Yes. We remove the old filler and start again. Tell us about it when you send photos.
Do you work in Cove?
Yes. We work across the UK and come to Cove. Send us pictures for a fixed quote, or call 0345 017 0787.
What information do you need?
Just photos, your postcode and a contact number. On the day, we only need access to the room.
Do you hold any accreditations?
Yes, including CHAS, Constructionline and SafeContractor. The full list is on our accreditations page.
It’s been repaired before. Can you still fix it?
Most of the time. Let us know what was used before and we will plan for it.
Is a cracked acrylic bath repairable?
Most of the time. The back of the crack is strengthened before the front is filled and refinished, so access behind the panel is important.
Will you leave a mess?
No. The work area is masked and covered, and we take our waste away with us.
Do I have to be there?
Yes. We need access to the room while we work, at a time we agree with you.
What your bath is made of matters
Pressed steel
Under the enamel of a steel bath is thin metal. Exposed steel rusts quickly, so we treat and seal the metal before filling.
Acrylic
Acrylic feels warm and is light, but it needs firm support underneath. Repairs to cracks are reinforced from the back.
About our accreditations · Every repair comes with a one-year guarantee.
