Powys · Wales
Bath Repair in Evenjobb
Our repair technicians come to Evenjobb for chip and crack repairs to enamel, acrylic and cast iron baths. Everything is done in place, with a one-year guarantee.
- Repairs from £95
- Scuffs and scratches in the surface
- Cracks in an acrylic bath
Repair or replace: which is better?
Cast iron baths in particular are worth repairing: they’re very heavy to remove, especially upstairs, and a like-for-like replacement can be expensive. A repair keeps it in place. Our bath repair starts from £95. Every job is a little different, so each one is priced on its own. What’s damaged, how badly and how easy it is to reach all make a difference, and combining jobs on one visit brings the cost down.
Why book with us
- Repair technicians who travel to you, UK-wide
- A fixed quote before you book
- A year’s guarantee on all work
- We will tell you if it’s not worth repairing
See our full price list or resurfacing vs replacement cost guide.
Bath repair in Evenjobb without replacing anything
Repairing baths is what we do most. A chip by the taps, a crack in the base and a rust spot by the plughole are all repaired in place, normally in a single visit. Whether it’s a chip where the taps sit and rusty patches near the plughole, we can usually put it right, whatever the material.
The work is guaranteed for twelve months. If something is not right in that time, we come back and put it right.
- Where
- Evenjobb (LD8)
- Region
- Powys
- Warranty
- One year on every repair
- Quotes
- From £95. Free, fixed quote from pictures
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Materials and what they mean for the repair
Pressed steel
Steel baths are lighter than cast iron, but have a similar enamel surface. Exposed steel rusts fast, especially around the waste, so early repairs matter.
Composite and resin
Composite baths are dense and solid, and often freestanding. Chips and scratches are filled and matched, in much the same way.
Evenjobb: your questions answered
Do the materials smell?
A little, depending on the job. Open windows and an extractor fan help.
Do you work for landlords and businesses?
Yes. We work for landlords, agents, builders and businesses as well as householders.
Can rust on a bath be repaired?
Yes. We remove the rust and loose enamel, seal and fill the area, then colour-match the finish.
Can you repair a failed DIY repair?
Yes. We remove the old filler and start again. Mention it when you send photos.
When can you do it?
It depends on the time of year and where you are. Send pictures with your postcode and we will reply with the earliest dates.
Can you quote from pictures?
Nearly always. We only ask to see it in person if the photos cannot show what we need.
I’m a tenant. Can you help?
Yes. Check with your landlord; we can send the quote to them too.
Can I add another job to the visit?
Yes. Doing several items on one visit normally costs less than separate visits. Send pictures of everything you’d like done.
Can I fix it myself?
If you’re set on a kit, follow its instructions closely, ensure the area is clean and completely dry, and give it the full curing time. If it does not work out, we can still repair it properly.
If you’ve already tried a DIY fix, that’s fine. We remove the old filler and start again, so it will not stop us repairing it. It does add a little time, so tell us about it when you send photos.
Prices and what affects them
Prices start from £95. A fixed quote means you know the cost before booking. We look at:
- How hard the colour is to match
- The material
- How much damage there is
- How many items we do on one visit
There are no surprise extras on the day. The price we quote from your photos is the price you pay, and if the damage turns out to be different, we discuss it before starting.
Quotes from your pictures
Most quotes are done from pictures alone. To make it quick:
- Details of any past repairs
- One picture of the whole bath
- Something in shot to show the size
- Where you are, by postcode
You don’t need a survey visit. Photos are enough for us to price nearly every job: send a close-up, a wider shot and your postcode, and we will reply with a fixed quote.
What we do, step by step
We begin by going over the job with you, so you know exactly what we are doing. After that, protection goes down around the work area and we start. Allow a morning or an afternoon.
- First, we check the damage against your pictures and agree the plan.
- Any rust and loose material comes out, and the area is degreased.
- The damage is filled in layers and shaped to the curve of the bath.
- We tint the finish by hand to match the bath.
- Finally, it’s polished to match the shine and left to cure.
Before we arrive
- Tell us about parking, stairs or access
- Point us to the nearest place to park
- Tell us if there are stairs or a lift
Getting a price
No survey visit is needed: we price from pictures. Use the quote form, or ring 0345 017 0787 to talk it through, and we will come back with a fixed figure.
Advice
Covering Evenjobb
Evenjobb (Welsh: Einsiob) is about 21 miles south-east of Y Drenewydd, in Powys. Anywhere in LD8, we carry out the work at your property. Evenjobb is one of 234 places in Powys where we work. Our nearest city page is Birmingham, about 52 miles away.
We cover every part of the LD8 postcode area and the streets around it. Close by, we cover Burlingjobb (3 miles south), Slough (3 miles east), Bradnor Green (3 miles south-east), Presteigne (3 miles east) and Norton (4 miles north-east). Within a short drive, we also cover Llandrindod Wells (13 miles west), Knighton (6 miles north) and Llanelwedd (15 miles south-west).
Near you in Evenjobb
Locally, our jobs take us to homes close to Bethel English Baptist Church. Other landmarks nearby include Knighton Museum (3.3 miles north-east) and Evenjobb Motte (within half a mile north). The countryside around Evenjobb includes Pen Offa and Titley Pool.
Landlords, agents and businesses in Evenjobb
We work for landlords, letting agents and housing providers in Evenjobb as well as homeowners. A repair between tenants keeps the property empty for less time, and it generally costs far less than a refit.
We also carry out snagging repairs for builders and developers, putting right damage done during fitting so nothing needs replacing. We hold CHAS, Constructionline and SafeContractor accreditations.
Aftercare tips
To keep it looking its best for years:
- Do not scrub with anything abrasive
- Rinse it down after each bath
- Clean with warm water and a mild detergent
- Cover the bath during DIY or decorating
Treat the repaired area like the rest of the bath: a soft cloth and washing-up liquid is all it needs. Keep scouring pads and gritty cleaners away from it.
Avoid standing in a cracked acrylic bath until it’s fixed. Every use opens the crack a little more, and it can start to leak underneath.
When a repair is not the answer
Before booking, it’s worth knowing the limits:
- A bath that flexes because its feet or cradle have failed (that needs fixing first)
- Water coming from the waste or taps rather than the bath
- Metal that has corroded all the way through
If in doubt, send photos and we’ll say what we think before you book.
What we work on
- Pressed steel enamel
- Cast iron enamel
- Roll-top & freestanding
- Acrylic
- Whirlpool & spa baths
Also near Evenjobb
More services for Evenjobb
About our accreditations · Every repair comes with a one-year guarantee.
