Dorset · England
Bath Repair for Pymore homes
Bath repair for Pymore, without a refit. Send us pictures for a fixed quote, then we come to you.
- Repairs from £95
- Chips under the taps
- Snagging damage from a refit
What your bath is made of matters
Pressed steel
Steel baths and trays have a thin metal body under the enamel. Once a chip exposes it, rust follows quickly, so we treat and seal the metal before filling.
Composite and resin
Stone resin and composite baths are heavy and solid. Chips and scratches can be filled and colour-matched, in much the same way.
Bath repair at your home in Pymore
Repairing baths is what we do most. A chip by the taps, a crack in the base and a rust spot by the plughole are all fixed without removing the bath, normally in one visit. If you are dealing with damage done while the bathroom was being fitted and a hole punched through by something heavy, we can normally put it right, on pressed steel enamel, roll-top & freestanding and cast iron enamel alike.
A one-year guarantee comes with the work, just as it does everywhere we cover.
- Where
- Pymore (DT6)
- Area hub
- Dorset
- Warranty
- A year, on every repair
- Price
- From £95. Fixed and free, based on photos
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Common problems we fix in Pymore
Heavy toiletries are the biggest single cause of chips. Taps and wastes cause problems too: water collects there, so chips nearby rust quickly.
Clients usually contact us about:
- Cracks in an acrylic bath
- Chips on the rim or sides
- An old repair that has yellowed or come loose
- Deep scratches in acrylic
Comparing quotes
- Who will actually do the work
- Whether there are any call-out or travel charges
- How long it needs to cure
- What prep work is covered
Should I try a DIY kit first?
You can buy a DIY kit for most repairs, and they can tidy up a tiny mark. Where they fall down is colour and preparation: they come in a handful of shades, and if the surface is not prepared the repair will not last.
A DIY attempt is not a disaster. We remove the old filler and start again, so it doesn’t stop a professional repair. Just mention it when you send photos, as it can add time.
How it works
Your technician turns up when we said we would, introduces themselves and looks over the damage before anything else. The floor and nearby surfaces are covered before any work starts. The work itself takes two to three hours for most chips, and the room is left clean and tidy.
- We clean the area and remove any loose enamel or rust.
- The chip or crack is filled, then sanded level with the bath.
- We tint the finish on the day to suit your bath’s shade of white or colour.
- We apply the finish coats and polish the repair so it blends in.
- Once it has cured, generally by the next day, the bath is ready to use.
Before we arrive
- Let us know which floor the room is on
- Keep a parking space free if you can
- Tell us about any previous repairs or coatings
Get a quote
Pricing is simple: take a close-up of the damage and a photo from further back, send them over with your postcode, and you’ll get a fixed price back. There’s no charge for the quote and no obligation.
Related advice
How we price bath repair
Repairs from £95. You’ll know the full cost before booking. We look at:
- How many areas need work
- What kind of damage it is
- Any earlier repairs that need removing first
- The colour and finish to match
A few things move the price: the amount of damage, the material, access to the area, and how many jobs we do in one trip. Photos let us give you a fixed figure.
Getting a price from pictures
Photographing the damage takes a minute, and it saves a visit. Please include:
- Daylight if possible, and no flash reflection
- A wider photo showing the whole bath
- A close-up of the damage, in focus
- The postcode, so we can plan the visit
Getting a quote takes a couple of minutes: take one close-up and one wider shot of the bath, include your postcode and send them to us. What comes back is a fixed price, not a guess.
Other services in Pymore
FAQs for Pymore
Do you hold any accreditations?
We are accredited with CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile.
It’s been repaired before. Can you still fix it?
Yes, we frequently do. It can add a little time, which we include in the quote.
I’m a tenant. Can you help?
Yes, though it’s best to check with your landlord first. Landlords are often glad to have it sorted before the end of a tenancy.
Is repairing better than replacing?
Usually, if the item is otherwise sound. Repairing avoids the cost and disruption of replacing. If replacing would be better, we will say so.
Are there extra charges for Pymore?
We don’t add a call-out fee. Your fixed quote includes everything.
Will you leave a mess?
No. The work area is masked and covered, and we leave the room clean.
Can I add another job to the visit?
Of course, and it generally saves money. Just add the extra items to your photos and we’ll quote them together.
What happens next?
We come back with a fixed quote, plus dates. There is no obligation to book.
Honest limits
Some problems need a builder, plumber or fitter rather than us:
- Acrylic cracks with no access behind them
- A steel bath rusted through
- A bath worn all over, where resurfacing makes more sense
Send us photos and we’ll tell you honestly before booking.
Surfaces we repair
- Whirlpool & spa baths
- Acrylic
- Pressed steel enamel
- Roll-top & freestanding
- Cast iron enamel
Keeping it looking good
Looking after the surface is easy:
- Rinse it down after each bath
- Get any new chip repaired before it rusts
- Check that an acrylic bath does not move when you stand in it
- Store metal items away from the bath
For the first few days, keep heavy bottles off the repaired spot. After that, clean it as you would the rest of the bath, avoiding abrasives.
Small chips are quick to repair. Left alone, they stain and can rust, so it’s worth getting them done early.
For landlords and businesses
If you manage property in Pymore, we can repair and quote for several addresses together. Just send photos for each address and we’ll come back with a combined price.
Builders, developers and site managers book us for snagging repairs, fixing chips and scratches before handover so nothing needs replacing. We hold CHAS, Constructionline and SafeContractor accreditations.
Our work in Pymore
Pymore is about 1 mile north of Bridport, in Dorset. Customers in Pymore get the same service as everywhere else we cover: a fixed quote from pictures, then a visit to do the work. Pymore is one of 462 towns and villages in Dorset where we work.
Every address in DT6 is covered. From Suttil Crescent, Pond End and Morbae Grove or a nearby road, a technician can come to you. Neighbouring places we cover include Bradpole (1 mile east), Dottery (1 mile north-west), Allington (1 mile south-west), Bridport (1 mile south) and New Zealand (1 mile south). Larger places within reach include Dorchester (14 miles east), Fordington (14 miles east), Lyme Regis (8 miles west), Chickerell (14 miles south-east), Beaminster (4 miles north) and Broadwey (14 miles south-east).
Around Pymore
In Pymore, that means homes near Parish Church of Holy Trinity, St Catherine's Roman Catholic School and Pymore Inn, among other places. Further afield, we also cover the area around Burcomb Wood (3.7 miles north-east) and Bridport Community Hospital (0.9 miles south-west). The countryside around Pymore includes Thorncombe Beacon.
About our accreditations · Every repair comes with a one-year guarantee.
