Derbyshire · England
Bath re-enamelling & resurfacing in Bole Hill, Derbyshire
Bath re-enamelling in and around Bole Hill: a fixed quote from pictures, a tidy visit and a one-year guarantee.
- Resurfacing from £350
- Brown or grey marks that don’t clean off
- Worn patches where water runs and sits
Should you replace it?
Replacement only makes sense in a few cases: a cracked-through bath, a change of size or shape, or a full refit. In most other cases, resurfacing is the better choice. Resurfacing from £350, with every job priced individually. A repair is priced on what needs doing, not where you live. You will see the full price before booking.
Why us?
- Accredited with CHAS, Constructionline and SafeContractor
- Dust sheets down, tidy finish
- Colour-matched on site
- Most jobs done in one visit
See our pricing and bath cost comparison.
About our bath re-enamelling in Bole Hill
Resurfacing renews the entire surface of the bath without taking anything out. It’s the answer when the whole bath is tired rather than one spot. Whether it’s a peeling or bubbling previous coating and several chips and rust patches, we can help.
You’re covered after we leave: each job carries a one-year guarantee, and we’ll explain exactly what it covers when we quote.
- Location
- Bole Hill (S42)
- County
- Derbyshire
- Cover
- One year on every repair
- Price
- From £350. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Also near Bole Hill
Other services in Bole Hill
Landlord and trade work in Bole Hill
For anyone letting property in or around Bole Hill, we can repair and quote for several addresses together. Just send photos for each address and we will price them together.
We regularly price jobs from inventory or check-out photos. You can have a price before you arrange access, and we can arrange access with the tenant directly if that helps.
How the visit works
We turn up when we said we would, introduces themselves and checks the damage against your photos first. Dust sheets and masking tape go down before any work starts. The work itself takes a full day, and the room is left clean and tidy.
- We sheet, mask and ventilate the room.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures until the day after.
Before we arrive
- Point us to the nearest place to park
- Tell us if there are stairs or a lift
- Clear toiletries, mats and anything else from around the area
Get a quote
Call 0345 017 0787 or use the quote form. With one close-up and one wider picture, we can give you a fixed quote.
Advice
Repairs by material
Roll-top and period baths
We can resurface a roll-top inside and out, and the outside can be refinished too.
Acrylic
We resurface acrylic baths as well, with a coating system suited to acrylic. It must be solid and not flex underfoot for the finish to last.
Bole Hill questions
Can landlords book you?
Yes, often. We can quote for several properties together and work between tenancies.
Does someone need to be in?
Yes. The technician needs access to the room for the visit, at a time that suits you.
Do you resurface freestanding baths?
Yes, roll-tops are a big part of our work. We resurface the inside, and the outside can be refinished too.
Can I get a quote without a visit?
Yes, almost always. Clear pictures let us give you a fixed price without visiting.
Will the price change on the day?
Your quote covers the damage in the photos. Anything extra is discussed before we begin.
Do you work in Bole Hill?
Yes, we do. Repair technicians travel to Bole Hill from across the region, and the price is the same as everywhere else.
How much does bath re-enamelling cost in Bole Hill?
Prices start from £350. We give a fixed price based on photos of the damage. Send a close-up of the damage and a wider photo and your postcode.
How long does re-enamelling last?
Look after it and it lasts. Gentle cleaning, no suction mats.
What we cannot put right
A repair is not always the answer, and we’d rather say so up front. We can’t fix:
- Steel that has corroded right through
- Plumbing leaks, which need a plumber
- A cast iron or steel bath that is cracked right through
If in doubt, send photos and we will say what we think before booking.
Materials we repair
- Cast iron baths
- Victorian roll-tops
- Pressed steel baths
- Basins & shower trays
- Acrylic baths
How we price bath re-enamelling
Prices start from £350. Every quote is fixed and free. What we look at:
- How many items we do on one visit
- The colour and finish to match
- Access to the area
- The size and number of damaged areas
Set against the cost of replacement, a repair is normally a fraction of the price, because nothing has to be taken out, refitted or made good. The quote lists exactly what you’re paying for.
Getting a price from pictures
Two or three clear photos are typically enough. Try to include:
- The material, if you know it
- Any earlier repairs or coatings
- Good light, ideally daylight, without flash glare
- A picture taken from further back
There is no need for us to visit first. Photos are enough for us to price nearly every job: send a close-up, a wider shot and your postcode, and we’ll come back to you with a fixed figure.
Can I fix it myself?
If you do try a kit, read the instructions carefully, and don’t use it until it has fully cured. If it doesn’t work out, we can still repair it properly.
We understand the appeal of fixing it yourself. The trouble is that kit repairs frequently look fine at first and then fail, and the old filler has to come out before a proper repair.
When to call us in Bole Hill
Enamel does not fail overnight. Abrasive cleaners, limescale and years of use wear the gloss away, typically first under the taps and around the waste.
People usually call us after spotting one of these:
- A coloured bath you want in white
- An original cast iron bath that needs restoring
- Thin, worn enamel in places
- Lots of chips and rust spots
What to look for in a quote
- Who turns up on the day
- What protection goes down before work starts
- What preparation is included
- How soon you can use it again
About Bole Hill
Bole Hill is about 4 miles south of Chesterfield, in Derbyshire. We visit homes and businesses in Bole Hill and the surrounding area, so nothing has to leave your home. Our technicians cover all 532 towns and villages across Derbyshire, from the larger towns to small villages. Our nearest city page is Manchester, about 37 miles away.
We cover every part of S42 and the streets around it. Whether you live on Press Lane and Bolehill Lane or anywhere nearby, we can come to you. Close by, we cover Press (1 mile south-east), Northedge (1 mile south-west), Hardwick Wood (1 mile north-east), Alton (1 mile south) and Farhill (1 mile south). Within a short drive, we also cover Chesterfield (4 miles north), Belper (11 miles south), Heanor (13 miles south), Dronfield (8 miles north), Ripley (10 miles south) and Bolsover (8 miles north-east).
Landmarks near Bole Hill
Locally, our jobs take us to homes close to Tupton Hall School and Deer Park Primary School. The closest station to Bole Hill is Chesterfield station, about 4 miles north of the centre. Nearby you’ll also find Clay Cross Hospital (2.4 miles south-east) and Clay Cross Urban District (2.3 miles south-east). Open spaces near Bole Hill include Beeley Moor.
About our accreditations · Every repair comes with a one-year guarantee.
