Surrey · England
Bath re-enamelling & resurfacing in Claygate, Surrey
Problem with your bath in Claygate? We put it right where it is, match it on site and back it with a one-year guarantee.
- Resurfacing from £350
- Wear marks under the taps
- Several chips and rust patches
When to call us in Claygate
Enamel wears gradually. Abrasive cleaners, limescale and years of use dull the surface, starting where water runs and sits.
These are the problems we are asked about most:
- Wear marks under the taps
- Several chips and rust patches
- A bath in a colour that no longer suits
- Staining under the taps and around the waste
Comparing quotes
- How long the guarantee is and what it covers
- If travel is included in the price
- How the colour is matched
- How your room will be protected
How we handle bath re-enamelling in Claygate
After re-enamelling, the bath has a smooth, glossy, new-looking surface, without any of the disruption of replacing it. It suits anyone happy with the bathroom apart from the bath. We regularly repair basins & shower trays, cast iron baths and pressed steel baths, and common reasons people contact us are a coating lifting around the plughole and an outdated colour you’d like to change.
We guarantee the work for a year. If something isn’t right in that time, we come back and put it right.
- Where
- Claygate (KT10)
- Region
- Surrey
- Guarantee
- 12 months on all our work
- Quote
- From £350. Fixed and free, based on pictures
- Call
- 0345 017 0787
- Last updated
- 23 October 2026
Different materials, different repairs
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. The enamel is the part that wears or chips, and that’s the part we put right.
Roll-top and period baths
Freestanding roll-tops can be done inside and out, and the outside can be refinished too.
DIY repairs versus a professional job
If you do try a kit, read the instructions carefully, ensure the area is clean and completely dry, and do not use it until it has fully cured. If it fails, we can still put it right.
DIY kits are sold for most surfaces, and they can make a small mark look better. Where they fall down is colour and preparation: they come in a handful of shades, and if the surface isn’t prepared the repair will not last.
Claygate and the surrounding area
Claygate is about 3 miles south-west of Surbiton, in Surrey. Anywhere in KT10, we come to you. Claygate is one of 395 places in Surrey where we work. Our jobs stretch from Claygate to London (about 14 miles away).
Our technicians cover all of the KT10 postcode area and the streets around it. Whether you live on Church Road, High Street and Station Road or a nearby road, a technician can come to you. Nearby, we also work in Barwell (1 mile south-east), Hinchley Wood (1 mile north), Esher (1 mile north-west), Hook (1 mile east) and Malden Rushett (2 miles south-east). Further out, we also cover Guildford (13 miles south-west), Woking (11 miles west), Epsom (3 miles south-east), Horley (15 miles south-east), Redhill (11 miles south-east) and Ewell (4 miles east).
What’s near Claygate
Typical jobs here are in homes near Chessington Community College, Church of Holy Trinity and Claygate Common and the streets around them. Other local landmarks include Claygate Primary School (under half a mile south-west) and Milbourne Lodge School (1.3 miles west). There’s a railway station in Claygate itself: Claygate station. Further afield, we also cover the area around Municipal Borough of Surbiton (2.1 miles north-east) and The Ashley Centre (3.6 miles south-east). Open spaces near Claygate include The Lake and Jubilee Wood.
Work for landlords and builders
Housing associations and facilities teams use us for planned and reactive repairs in Surrey and across the UK. Repairing in place avoids the disruption of a replacement, which matters when someone is living in the home.
If you manage property in Claygate, we can repair and quote for several addresses together. Just send photos for each address and we will come back with a combined price.
The process
We turn up when we said we would and looks over the damage before anything else. The floor and nearby surfaces are covered before we open a single tin. Most visits take a full day, and we leave the room as we found it.
- First we protect the bathroom and set up ventilation.
- The bath is cleaned, degreased and any chips or rust repaired.
- The surface is prepared and a bonding primer applied.
- Several coats of new finish are sprayed on.
- We leave it to cure, and it’s normally ready the following day.
Before we arrive
- Ensure the room can be ventilated
- Make sure the area is dry
- Tell us about any previous repairs or coatings
How to get a price
Getting a price is easy: take a close-up of the damage and a picture from further back, send them over with your postcode, and you’ll get a fixed price back. There is no charge for the quote and no obligation.
Advice
When a repair is not the answer
A repair is not always the answer, and we’d rather say so up front. We can’t fix:
- Plumbing leaks, which need a plumber
- A cast iron or steel bath that is cracked right through
- An acrylic bath that flexes badly underfoot
If in doubt, send pictures and we’ll say what we think.
What we work on
- Cast iron baths
- Pressed steel baths
- Basins & shower trays
- Victorian roll-tops
- Acrylic baths
Claygate questions
Do you work in Claygate?
We do. Technicians travel to Claygate from across the region, with no extra charge for travel.
Do you resurface freestanding baths?
Yes, frequently. We resurface the inside, and the outside can be refinished too.
Do you work for landlords and businesses?
We do, regularly. We can quote for several properties together and work between tenancies.
Can you do more than one item on the same visit?
Of course, and it typically saves money. Just add the extra items to your photos and you’ll get one combined price.
What happens next?
You get a fixed quote and available dates. If anything’s unclear, we’ll ask for another photo.
Do you need to take the bath out?
No. It’s re-enamelled where it stands, so the tiles and taps stay put.
Is it OK to have pets in the house?
We ask you to keep children and pets out of the room while we work. The rest of the house is unaffected.
Can a failed resurfacing be redone?
Yes. Stripping the old coating adds time, so it’s reflected in the quote.
Nearby places to Claygate
More services for Claygate
How we price bath re-enamelling
Resurfacing from £350. There are no hourly rates or hidden extras. The price is based on:
- The material and finish
- Whether it’s a chip, crack, burn or wear
- How many areas need work
- Previous DIY repairs that have to come out
The price depends on how much damage there is and what kind, what it’s made of and how many items we do on one visit. We give a fixed quote from your pictures, so you know the cost before you book.
Send photos for a quote
We price nearly every job from pictures. This is what we need:
- A wider photo showing the whole bath
- What it’s made of, if you know
- Your postcode, so we can check dates
- Something in shot to show the size
To get a price, send a couple of photos through our quote form or call us. We will tell you honestly if a repair is the right fix.
Why repair rather than replace?
Replacing a bath normally involves a plumber, a fitter and a tiler. Re-enamelling takes one technician and generally one day, with the bath ready the following day. Resurfacing from £350, with every job priced individually. Our prices are the same across the UK, so there is no premium for Claygate. The job itself decides the price: the material, the amount of damage and how many items.
Why Claygate customers choose us
- CHAS, Constructionline and SafeContractor accredited
- One price list for the whole UK
- Every repair guaranteed for a year
- Free fixed quotes from pictures
See our full price list and bath cost comparison.
About our accreditations · Every repair comes with a one-year guarantee.
