Greater London · England
Bath Re-enamelling in Malden Rushett
Bath re-enamelling for Malden Rushett, without a refit. Get a fixed quote from your pictures, then we come to you.
- Resurfacing from £350
- A bath that stays dull however much you clean it
- Lots of chips and rust spots
How it works
Here’s how a visit generally runs: we arrive at the agreed slot, protect everything around the work area, carry out the work and clear up. Allow the best part of a day. Before we go, we’ll explain when it can be used and how to care for it.
- The bathroom is protected and ventilation set up.
- We remove the old silicone and deep clean the bath.
- Chips, rust and pitting are repaired.
- The surface is keyed and primed for the new finish.
- The new finish is sprayed on in several coats and left to cure until the next day.
How to prepare
- Make sure the area is dry
- Keep a parking space free if you can
- Let us know which floor the room is on
Ask for a price
To get a price, send two or three pictures through our quote form or call us. We will tell you honestly if a repair is the right fix.
Read more
Bath re-enamelling at your home in Malden Rushett
When a bath is structurally fine but worn out on the surface, re-enamelling is normally the most cost-effective option. There is no removal, plumbing or tiling involved. Whether it’s an outdated colour you’d like to change and chips and rust in more than one place, we can usually put it right, whatever the material.
Peace of mind is built in: our one-year guarantee applies to every job, and we explain what it covers before you book.
- Where
- Malden Rushett (KT9)
- Region
- Greater London
- Guarantee
- One year on every repair
- Quote
- From £350. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
How we price bath re-enamelling
Prices start from £350. A fixed quote means you know the cost before you book. We look at:
- The colour and finish to match
- The material and finish
- Where the damage is and how we get to it
- The size and number of damaged areas
Instead of hourly rates, we price the entire job up front. Damage, material and access decide it, and doing several items at once reduces it.
Getting a price from photos
It only takes a minute to photograph the damage. Try to send:
- One picture of the whole bath
- Any earlier repairs or coatings
- Good light, ideally daylight, without flash glare
- Your postcode, so we can check dates
For a price in Malden Rushett, photos are the quickest way: one close up, one from further back, plus your postcode. We reply with a fixed quote and our next available dates.
Malden Rushett and nearby
Malden Rushett is about 2 miles north of Ashtead, in Greater London. Whether you’re in the middle of Malden Rushett or on the outskirts, the service is the same: fixed prices, tidy work and a one-year guarantee. We cover all 764 towns and villages in Greater London, from the larger towns to small villages. Our jobs stretch from Malden Rushett to London (about 15 miles away).
Every address in KT9 is within our area, from the main roads to the quietest streets. We regularly work on streets such as Silverglade, Leatherhead Road and West Road. We also cover the places around Malden Rushett: Barwell (1 mile north), Pachesham Park (1 mile south-west), Claygate (2 miles north-west), Oxshott (2 miles west) and Ashtead (2 miles south). We also work in nearby towns such as London (15 miles north-east), City of Westminster (14 miles north-east), Marylebone (14 miles north-east), Kensington (12 miles north-east), Brompton (13 miles north-east) and Stockwell (12 miles north-east).
Near you in Malden Rushett
We visit homes around Chessington Community College and Claygate Common. For rail, the closest station is Chessington South station, roughly 1.3 miles north of the centre. Well-known places in the area include Chessington Castle Hill (1.8 miles north-east) and The Ashley Centre (2.2 miles east). Open spaces near Malden Rushett include The Lake and Jubilee Wood.
- Parks and local facilities nearby include Municipal Borough of Surbiton (2.7 miles north)
When we would advise against a repair
Not everything can be repaired, and we would rather say so up front. We cannot fix:
- Anything hidden under an old coating, until we remove it
- Leaks from fittings rather than the bath
- A bath split right through the body
Not sure? Send photos and we’ll give you a straight answer.
Surfaces we repair
- Basins & shower trays
- Acrylic baths
- Cast iron baths
- Victorian roll-tops
- Pressed steel baths
Looking after it afterwards
So the finish stays in good condition for years:
- A dripping tap should be fixed promptly
- Do not leave bottles, razors or sponges standing on the surface
- Clean with a soft cloth and mild detergent
- Do not leave a chip unrepaired
Wait for the curing time we give you before the first bath. Then, gentle cleaning with a soft cloth is enough.
Leave a peeling coating alone. Water gets under it and the damage spreads, so it’s better to have it stripped and redone.
Questions from Malden Rushett
Does the bath have to be removed?
Not at all. We work on the bath in place, with the room masked and ventilated.
Are you a vetted contractor?
We’re accredited with CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile.
Is it safe with children and pets around?
Please keep children and pets out of the room during the visit and until it has cured. Everywhere else in the home is fine.
Can you price it without visiting?
Usually, yes. Clear photos let us give you a fixed price without visiting.
Will there be fumes?
A little, during the work. Ventilation keeps it down, and it fades as the finish cures.
Will you leave a mess?
Very little mess: we sheet and mask everything nearby, and we take our waste away with us.
Can you resurface a pink bath in white?
Yes, most people go for white. Tell us what you’d like when you ask for a quote.
Can you re-enamel a roll-top bath?
Yes. Inside and out if you’d like.
More services for Malden Rushett
Repair or replace in Malden Rushett?
Getting a cast iron bath out is hard work: they’re heavy, frequently need breaking up, and a new one is not cheap. Resurfacing in place avoids that entirely. Our bath re-enamelling starts from £350. No two jobs are quite the same, so each one is priced on its own. The size and type of damage, the material and access all play a part, and combining jobs on one visit brings the cost down.
Why Malden Rushett customers choose us
- We come to you, anywhere in the UK
- A year’s guarantee on all work
- Most jobs done in one visit
- CHAS and Constructionline accredited
See our pricing and bath cost comparison.
DIY kit or professional repair?
If you are set on a kit, follow its instructions closely, and give it the full curing time. If it fails, we can still put it right.
You can buy a DIY kit for most repairs, and they can tidy up a tiny mark. Where they fall down is colour and preparation: kits come in a few standard shades, and without proper cleaning and keying the filler frequently lifts.
What we’re called out for in Malden Rushett
Enamel wears gradually. Abrasive cleaners, limescale and years of use dull the surface, starting where water runs and sits.
Get in touch if you’ve noticed any of these:
- Wear marks under the taps
- Stains that won’t shift
- A dull, rough surface that won’t come clean
- Chips and rust in more than one place
Before you book anyone
- What happens if they find more damage
- Whether the colour is mixed to match
- The length of the guarantee and what it covers
- How soon you can use it again
Materials and what they mean for the repair
Pressed steel
Under the enamel of a steel bath is thin metal. Exposed steel rusts quickly, so we treat and seal the metal before filling.
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. The enamel is the part that wears or chips, and that is the part we put right.
About our accreditations · Every repair comes with a one-year guarantee.
