Newport · Wales
Bath re-enamelling & resurfacing in Gaer, Newport
Full bath re-enamelling and resurfacing for homes and businesses in Gaer and across Newport. Free, fixed quotes from your photos.
- Resurfacing from £350
- Enamel that’s lost its shine and feels rough
- A peeling or bubbling previous coating
Do you need bath re-enamelling in Gaer?
Older baths often have several problems at once: worn patches, chips, rust spots and stains. Resurfacing sorts them out together.
Customers usually contact us about:
- Chips and rust in more than one place
- An original cast iron bath that needs restoring
- Worn patches where water runs and sits
- A dull, rough surface that will not come clean
Before booking anyone
- Who turns up on the day
- Whether the price covers travel
- How to look after the finish
- What preparation is included
About our bath re-enamelling in Gaer
Resurfacing renews the whole surface of the bath without taking anything out. It’s the answer when the entire bath is tired rather than one spot. If you’re dealing with a bath that stays dull however much you clean it and a roll-top that’s seen better days, we can help, on basins & shower trays, acrylic baths and pressed steel baths alike.
We stand behind the work with a one-year guarantee, so you’re covered after the visit.
- Area
- Gaer (NP20, NP10)
- Area hub
- Newport
- Warranty
- 12 months on all our work
- Quote
- From £350. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Work for landlords and builders
We also carry out snagging repairs for builders and developers, putting right damage done during fitting so nothing needs replacing. We are CHAS, Constructionline and SafeContractor accredited.
Rental properties take more wear, and replacing items every time a tenant leaves is expensive. A repair between tenancies is a cheaper way to keep the property in good order.
The process
Visits start with a quick look at the job together. Next, we cover and mask everything nearby and we start. You can expect it to take a full day, and we will keep you posted as we go.
- First we protect the bathroom and set up ventilation.
- We clean and degrease the bath and repair any chips or rust.
- We prepare the surface and apply a bonding primer.
- We spray several coats of new enamel finish.
- We leave it to cure, and it’s generally ready the following day.
Preparing for the visit
- Let us know if it has been repaired before
- Let us know which floor the room is on
- Make sure the area is dry
How to get a price
A quote takes minutes to ask for: photograph the damage, then the whole bath, add your postcode and send them over. You’ll get a fixed price, not an estimate.
Advice
Nearby places to Gaer
More services for Gaer
What your bath is made of matters
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. Only the enamel surface wears or chips, and that’s what we repair.
Pressed steel
Steel baths re-enamel well, as long as any rust is dealt with first. Steel often rusts by the plughole, so we pay close attention there.
Gaer and nearby
Gaer is about 1 mile south-west of Stow Hill, in Newport. Our repair technicians come to clients in Gaer and the surrounding area, so there’s no workshop to go to. Gaer is one of 69 places in Newport we cover. Our jobs stretch from Gaer to Birmingham (about 78 miles away).
Postcode districts we cover here: NP20 and NP10. Local streets include Gaer Road, Byron Road and Park Avenue. Neighbouring places we cover include Pont Ebbw (1 mile south), Maesglas (1 mile south-east), Stelvio (1 mile north), Caerau Park (1 mile north) and Stow Park (1 mile north-east). Larger places within reach include Beechwood (3 miles north-east), Caerleon (4 miles north-east), Bishpool (4 miles north-east), Ringland (4 miles north-east), Alway (3 miles east) and Treberth (4 miles north-east).
Near you in Gaer
Typical jobs here are in homes near Belle Vue Park, St David's R.C. Junior & Infants School and Gaer Inn, among other places. Also close by are Emmanuel Evangelical Church (1.1 miles north-east), Ysgol Bryn Derw (less than half a mile north), Ysgol Tŷ Monmouth (0.7 miles north-east) and Church of Saint Basil (1.2 miles west). Gaer’s nearest station is Pye Corner station, roughly 1.1 miles north-west. A little further out are St Woolos Hospital (0.9 miles north-east) and Friars Walk (1.4 miles north-east). The countryside around Gaer includes Somerton and Graig Ddifaith.
FAQs for Gaer
Will the price change on the day?
It’s rare, but if it happens we talk to you first. You decide whether to go ahead.
Is the work guaranteed?
Yes, for a year. If anything goes wrong with the repair within the year, we return to fix it.
Does re-enamelling smell?
Some odour is normal while we spray, so we ventilate the room. It fades as the coating cures.
How quickly can you book me in?
It depends on the time of year and where you are. Send pictures with your postcode and we’ll reply with the earliest dates.
It’s been repaired before. Can you still fix it?
Generally, yes. Tell us what was done before and we’ll plan for it.
Can you re-enamel a roll-top bath?
Yes. We can do the inside and outside.
Do you need to take the bath out?
No, it stays where it is. Everything is done in your bathroom, with the room protected and ventilated.
Do I need to be at home?
Someone needs to let us in and show us the job. After that, you can carry on with your day.
Honest limits
A few problems are outside what a surface repair can do:
- Problems we cannot see until an old finish comes off
- A poorly supported acrylic bath, until it’s firmed up
- Holes rusted through the metal
Send us pictures and we’ll tell you honestly.
Materials we work on in Gaer
- Cast iron baths
- Basins & shower trays
- Victorian roll-tops
- Pressed steel baths
- Acrylic baths
Prices and what affects them
Resurfacing from £350. Prices are worked out job by job, from your photos. What matters most is:
- Whether we combine several jobs
- What the surface is made of
- Previous DIY repairs that have to come out
- The colour and finish to match
No two jobs are quite the same, so we price each one individually. The size and type of damage, the material and access all play a part, and doing several things on one visit costs less than separate visits.
How to get a fixed price
Two or three clear pictures are generally enough. It helps if you send:
- One sharp close-up of the damage
- Whether it’s been repaired or coated before
- Something in shot to show the size
- One picture of the whole bath
We price from pictures so you don’t have to wait in for a survey. Use the quote form, or ring 0345 017 0787 to talk it through, and we’ll come back with a fixed figure.
Looking after it afterwards
How the surface is treated afterwards matters. Here’s what we suggest:
- A dripping tap should be fixed promptly
- Leave the bath for the full curing time before using it
- Do not leave a chip unrepaired
- Wipe the bath dry after use in hard water areas
Give the finish its full curing time before using the bath. Then, gentle cleaning with a soft cloth is enough.
Avoid scrubbing a dull bath with abrasive cleaners. It removes more of the surface.
DIY repairs versus a professional job
The difference between a kit and a professional repair is mostly in the preparation and colour. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, and the work is guaranteed.
You can buy a DIY kit for most repairs, and they can tidy up a tiny mark. The trouble is colour and preparation: they come in a handful of shades, and if the surface is not prepared the repair will not last.
About our accreditations · Every repair comes with a one-year guarantee.
