Aberdeenshire · Scotland
Bath Re-enamelling for Johnshaven homes
Damaged bath in Johnshaven? We repair it in place, mix the colour on the day and back it with a one-year guarantee.
- Resurfacing from £350
- A coating lifting around the plughole
- Wear marks under the taps
How the visit works
We agree an arrival time beforehand. On site, it takes the best part of a day for most jobs. The room is left tidy.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures until the following day.
Getting ready for the visit
- Mention any parking restrictions or tricky access
- Avoid using the area for a few hours before we arrive
- Move bottles, mats and clutter away from the area
How to get a price
Pricing is simple: snap the damage close up and then the entire item, send them to us with your postcode, and you will get a fixed price back. Quotes are free and you are under no obligation.
Related advice
About our bath re-enamelling in Johnshaven
Resurfacing renews the entire surface of the bath without taking anything out. It suits baths that are dull, stained, rough or chipped all over. We work on acrylic baths, pressed steel baths and cast iron baths, and people most frequently call us about a coloured bath you want in white and a dull, rough surface that won’t come clean.
Big or small, you get the same one-year guarantee in Johnshaven and across Aberdeenshire.
- Location
- Johnshaven (DD10)
- County
- Aberdeenshire
- Cover
- A year, on every repair
- Price
- From £350. Fixed and free, based on pictures
- Telephone
- 0345 017 0787
- Page updated
- 23 October 2026
Covering Johnshaven
Johnshaven is about 8 miles north-east of Montrose, in Aberdeenshire. Across the DD10 area, we come to you. Johnshaven is one of 161 places in Aberdeenshire where we work. Our jobs stretch from Johnshaven to Edinburgh (68 miles away).
All of DD10 is covered. Jobs here include addresses on Square, Main Street and Mid Street. We also travel to Gourdon (3 miles north-east), St Cyrus (3 miles south-west), Inverbervie (4 miles north-east), Arbuthnott (5 miles north) and Laurencekirk (6 miles north-west). Further out, we also cover Montrose (8 miles south-west), Stonehaven (13 miles north), Hillside (6 miles south-west) and Ferryden (8 miles south-west).
Around Johnshaven
Locally, our jobs take us to homes close to Johnshaven. Nearby you’ll also find Benholm Castle (2.1 miles north). Open spaces near Johnshaven include St Cyrus National Nature Reserve.
Repairing versus replacing in Johnshaven
Replacing a bath typically involves a plumber, a fitter and a tiler. Resurfacing is one technician, normally in a day, with the bath ready the day after. Resurfacing from £350, with every job priced individually. Set against the cost of replacement, a repair is generally a fraction of the price, because nothing has to be taken out, refitted or made good. The quote lists exactly what you’re paying for.
Why choose Surface Doctor in Johnshaven
- Every repair guaranteed for a year
- Honest advice, even when it means no job
- Dust sheets down, tidy finish
- A fixed quote before you book
See our pricing or resurfacing vs replacement cost guide.
Landlord and trade work in Johnshaven
We are used to working with agents and managing companies. Send the address, pictures and access details.
If you manage property in Johnshaven, we can repair and quote for several addresses together. Send photos for each one and we’ll come back with a combined price.
Signs you need bath re-enamelling in Johnshaven
Sometimes it’s an earlier resurfacing that has failed, lifting by the plughole or blistering. We strip what’s failing and start again.
The most common problems we are called about are:
- A roll-top that’s seen better days
- Lots of chips and rust spots
- A bath that stays dull however much you clean it
- Worn patches where water runs and sits
Before you book anyone
- If travel is included in the price
- What protection goes down before work starts
- How to look after the finish
- What prep work is covered
What affects the price in Johnshaven
Prices start from £350. A fixed quote means you know the cost before you book. We take into account:
- How hard the colour is to match
- How many items we do on one visit
- What kind of damage it is
- Where the damage is and how we get to it
A repair usually costs much less than people expect, particularly next to the cost of replacement. Send pictures and we will give you the exact figure.
Quotes from your pictures
Phone pictures are fine. Just make sure we can see:
- Good light, ideally daylight, without flash glare
- One picture of the whole bath
- What it’s made of, if you know
- A coin or ruler next to the damage for scale
Email us a picture of the damage and one of the whole item, and tell us you’re in Johnshaven, and we’ll come back with a fixed quote.
Your questions about bath re-enamelling in Johnshaven
How long is the bath unusable?
Generally a day, then it’s ready to use the following day. Deeply pitted baths may need a second day.
What does bath re-enamelling cost?
Resurfacing from £350. We give a fixed quote from your pictures. Send a close-up and a photo of the whole item and your postcode.
Do you resurface freestanding baths?
Yes, roll-tops are a big part of our work. We resurface the inside, and the outside can be refinished too.
How durable is a resurfaced bath?
Care for it and it lasts. Gentle cleaning, no suction mats.
Does re-enamelling smell?
There is some smell while the coating is applied, so we ventilate the room. It fades as the coating cures.
Can you resurface a pink bath in white?
Yes, most people go for white. Tell us what you’d like when you ask for a quote.
Do you work for landlords and businesses?
We do, regularly. We quote for multiple addresses and fit around tenancy changeovers.
Can tenants book a repair?
Yes. Ask your landlord first, and we can send them the quote if that helps.
Also near Johnshaven
Also in Johnshaven
Repairs by material
Acrylic
Acrylic baths can be resurfaced too, using a system that bonds to acrylic. It must be solid and not flex underfoot.
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. The enamel is the part that wears or chips, and that’s what we repair.
Can I fix it myself?
For a hairline mark somewhere you’ll never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, a professional repair is worth it.
We understand the appeal of fixing it yourself. The risk is that a kit repair hides the damage for a while, then fails, and the old filler has to come out before a proper repair.
Aftercare tips
After the repair has cured, a few habits help it last:
- Avoid suction-cup mats
- Stick to gentle, non-abrasive cleaners
- Do not let dyes or oils sit on the finish
- Have chips seen to early
Rinse the bath and wipe it over after use, particularly where water is hard, so limescale can’t build up.
Leave a peeling coating alone. Water gets under it and the damage spreads, so it’s better to have it stripped and redone.
About our accreditations · Every repair comes with a one-year guarantee.
