Oxfordshire · England
Bath Re-enamelling for Milcombe homes
Local bath re-enamelling for Milcombe: a fixed quote from photos, a tidy visit and a one-year guarantee.
- Resurfacing from £350
- An original cast iron bath that needs restoring
- Stains that will not shift
Bath re-enamelling in Milcombe without replacing anything
Resurfacing renews the whole surface of the bath without a refit. It’s the answer when the entire bath is tired rather than one spot. Whether it’s a peeling or bubbling previous coating and chips and rust in more than one place, we can normally put it right, whatever the material.
We guarantee the work for a year. If there is a problem with the repair within the year, we return and sort it.
- Location
- Milcombe (OX15)
- Area hub
- Oxfordshire
- Cover
- 12 months on all our work
- Price
- From £350. Free and fixed, from your pictures
- Call
- 0345 017 0787
- Last updated
- 23 October 2026
What happens on the day
There is not much you need to do on the day. Let us in and show us the room, and we will take it from there. Most visits take a full day.
- We sheet, mask and ventilate the room.
- We remove the old silicone and deep clean the bath.
- We repair chips, rust spots and pitting.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures until the following day.
Before we arrive
- Mention any earlier repairs or resurfacing
- Clear toiletries, mats and anything else from around the area
- Point us to the nearest place to park
Ask for a price
Getting a quote takes a couple of minutes: take one close-up and one wider shot of the bath, add your postcode and send them to us. What comes back is a fixed quote, not a guess.
Advice
Towns and villages near Milcombe
More services for Milcombe
Work for landlords and builders
For developers and builders, we fix damage before handover, saving last-minute replacements. Several plots can be done in one visit to keep costs down.
Housing associations and facilities teams use us for planned and reactive repairs in Oxfordshire and across the UK. A repair avoids taking out and refitting, which matters when someone is living in the home.
Where we work around Milcombe
Milcombe is about 4 miles south-west of Banbury, in Oxfordshire. Customers in Milcombe get the same service as everywhere else we cover: a fixed quote from pictures, and a technician at your door on the day. We work in 443 places across Oxfordshire. You can also see our page for Birmingham, about 38 miles away.
Every address in OX15 is within our area, from the main roads to the quietest streets. Streets in the area include Station Road, Barlow Close and Main Road. We also travel to Tadmarton (2 miles north-west), Swalcliffe (3 miles north-west), Sibford Ferris (4 miles north-west), Burdrop (4 miles north-west) and Shutford (4 miles north-west). We also work in nearby towns such as Banbury (4 miles north-east), Bicester (13 miles south-east), Kidlington (14 miles south), Bure Park (13 miles south-east), Chipping Norton (8 miles south-west) and Neithrop (4 miles north-east).
Local landmarks in Milcombe
In Milcombe, that means homes near Bloxham Church of England Primary School, The Warriner School and Church of St Lawrence. Milcombe’s nearest station is Banbury station, about 4.8 miles north-east. Nearby you will also find Broughton Castle (2.2 miles north) and Horton General Hospital (4.2 miles north-east). Not far away are Woodford Bottom and Lamb's Pool and Crouch Hill.
DIY kit or professional repair?
It’s tempting to reach for a kit, but many of the jobs we do start with putting right a DIY repair. Doing it properly first is normally the cheaper route.
DIY kits are sold for most surfaces, and they can tidy up a tiny mark. The trouble is colour and preparation: kits come in a few standard shades, and without proper cleaning and keying the filler often lifts.
Milcombe questions
Are you accredited?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
Is there any odour?
Expect a mild smell while we’re working, which fades afterwards.
Are there extra charges for Milcombe?
Travel is included in the price, and we charge the same wherever you are.
Will you leave a mess?
No. The work area is masked and covered, and we leave the room clean.
How long does re-enamelling take?
Most baths are done in a day and can be used the day after. We will confirm timings when we quote.
How do I get a price for bath re-enamelling in Milcombe?
Resurfacing from £350. Because every job differs, we price from photos. You will get a fixed figure before you book.
What if the damage is worse than the photos show?
The price is fixed for what the photos show. If there’s more, we’ll tell you before starting.
How do I book?
Send pictures through the quote form or call 0345 017 0787.
When we would advise against a repair
A repair is not always the answer, and we’ll tell you before we start. We cannot fix:
- Damage hidden under a previous coating, until it’s stripped back
- An acrylic bath that flexes badly underfoot
- A bath that’s rusted through
If in doubt, send photos and we will say what we think.
Materials we work on in Milcombe
- Acrylic baths
- Basins & shower trays
- Pressed steel baths
- Cast iron baths
- Victorian roll-tops
Prices and what affects them
Prices start from £350. We charge the same across the UK, including Milcombe. What changes the price is:
- Where the damage is and how we get to it
- The size and number of damaged areas
- The material and finish
- Any earlier repairs that need removing first
What it costs depends on how much damage there is and what kind, what it’s made of and how many items we do on one visit. You get a fixed quote from your pictures, so you know the cost before booking.
Getting a price from photos
You can take the pictures on your phone, there’s no need for anything special. Just ensure we can see:
- A coin or ruler next to the damage for scale
- A wider photo showing the whole bath
- Details of any past repairs
- Where you are, by postcode
If you’re in Milcombe and want a price, pictures are the quickest way: one close up, one from further back, plus your postcode. We reply with a fixed quote and our next available dates.
Repairing versus replacing in Milcombe
For a sound bath, resurfacing costs far less than replacement, when you count removal, plumbing, tiling and decorating. It’s also far quicker. Prices start from £350. The price reflects the work involved, not your postcode. You’ll see the full price before you book, with nothing added on the day.
Why us?
- CHAS and Constructionline accredited
- One-year guarantee on every repair
- No extra charge for your area
- Dust sheets down, tidy finish
See our pricing and bath cost comparison.
Keeping it looking good
Good habits make a big difference to how long a repair lasts. Here’s what we suggest:
- Stick to gentle, non-abrasive cleaners
- Dry the bath after use to stop limescale
- Keep suction mats out of the bath
- Don’t leave a chip unrepaired
Wipe the bath dry after use where you can, especially in hard water areas, and rinse off any bath products.
Worn enamel only gets rougher with time, and rust spots spread under the surface. Resurfacing sooner means less repair work first.
Do you need bath re-enamelling in Milcombe?
Older baths often have several problems at once: worn patches, chips, rust spots and stains. Resurfacing sorts them out together.
If you can see any of these, send us a photo:
- Stains that will not shift
- Lots of chips and rust spots
- A period or roll-top bath worth keeping
- Wear marks under the taps
Questions to ask before booking
- If travel is included in the price
- How soon you can use it again
- A fixed price, and whether VAT is included
- How to care for the finish
About our accreditations · Every repair comes with a one-year guarantee.
