Cambridgeshire · England
Bath Re-enamelling for Turves homes
Fixed-price bath re-enamelling in Turves and the surrounding area, done in a single visit in most cases.
- Resurfacing from £350
- A coating lifting around the plughole
- Worn patches where water runs and sits
Bath re-enamelling at your home in Turves
Cast iron, steel, acrylic, roll-top and period baths can all be resurfaced. Several coats of finish go on over a bonding primer, once the bath has been cleaned, repaired and prepared. Typical jobs include brown or grey marks that don’t clean off and an original cast iron bath that needs restoring, across Victorian roll-tops, cast iron baths and acrylic baths.
All of our repairs are guaranteed for twelve months. If something goes wrong with the work, we come back.
- Where
- Turves (PE7)
- Region
- Cambridgeshire
- Cover
- A year, on every repair
- Quotes
- From £350. Fixed and free, based on photos
- Call
- 0345 017 0787
- Page updated
- 23 October 2026
Covering Turves
Turves is about 4 miles east of Whittlesey, in Cambridgeshire. We visit clients in Turves, so nothing has to leave your home. Turves is one of 371 towns and villages in Cambridgeshire where we work. We work right across the region, from Turves to London (about 73 miles away).
Postcode districts we cover here: PE7. Whether you live on March Road and Red Barn or a nearby road, a technician can come to you. Close by, we cover Eldernell (2 miles north-west), Oldeamere (2 miles west), Coates (2 miles west), Eastrea (3 miles west) and Westry (4 miles east). Further out, we also cover Wisbech (11 miles north-east), St Ives (15 miles south), Whittlesey (4 miles west), Chatteris (7 miles south-east), Yaxley (10 miles west) and Littleport (15 miles south-east).
Around Turves
The closest station to Turves is Whittlesea station, about 3.9 miles west of the centre. Open spaces near Turves include Lattersey.
Why repair rather than replace?
Replacing a bath usually involves a plumber, a fitter and a tiler. Resurfacing is one technician, normally in a day, with the bath ready the following day. Our bath re-enamelling starts from £350. The price reflects the work involved, not where you live. You will see the full price before booking, with nothing added on the day.
What you get with us
- Usually one visit, start to finish
- One price list for the entire UK
- Fixed prices from your photos
- One-year guarantee on every repair
See our pricing and resurfacing vs replacement cost guide.
Keeping it looking good
Once the work has cured, treat it gently:
- Do not leave a chip unrepaired
- Respect the curing time we give you
- Wipe the bath dry after use in hard water areas
- Rinse off hair dye, oils and bath bombs right away
Wait for the curing time we give you before the first bath. Then, gentle cleaning with a soft cloth is enough.
On a worn bath, rust spots keep spreading and make the job bigger. It’s simpler to resurface before they spread.
When we would advise against a repair
We’ll always be straight with you, so here’s what a repair will not do:
- An acrylic bath that flexes badly underfoot
- Steel that has corroded right through
- A cast iron or steel bath that is cracked right through
If in doubt, send pictures and we’ll say what we think.
What we work on
- Cast iron baths
- Victorian roll-tops
- Basins & shower trays
- Pressed steel baths
- Acrylic baths
Your questions about bath re-enamelling in Turves
Will the new finish last?
Care for it and it lasts. Avoid abrasive cleaners and suction mats.
Do you cover the entire of Cambridgeshire?
Across the UK, so Turves is covered. Our prices are the same everywhere.
What happens once I’ve sent photos?
You get a fixed price and available dates. If we need another angle, we will ask.
Will the bath be moved?
Not at all. We work on the bath in place, with the room masked and ventilated.
Can you re-enamel a roll-top bath?
Yes, roll-tops are a big part of our work. The inside is resurfaced, and we can refinish the outside as well.
Do you come to Turves?
We do. We send a technician to Turves for every job, and the price is the same as everywhere else.
What information do you need?
Send photos through the quote form or call 0345 017 0787.
Can you quote from photos?
Yes, almost always. A close-up and a wider photo are enough to give a fixed price.
What else we do in Turves
When to call us in Turves
Frequently the bath has just had decades of use, and only the surface is worn. Underneath, a cast iron or steel bath is typically as strong as ever.
Signs it’s time to call us include:
- Enamel that’s lost its shine and feels rough
- A coating lifting around the plughole
- A bath in a colour that no longer suits
- Wear marks under the taps
What to look for in a quote
- Aftercare advice
- If travel is included in the price
- Whether a trained technician does the job
- How your room will be protected
What bath re-enamelling costs
Resurfacing from £350. We don’t charge extra for travel to Turves. The price depends on:
- How many areas need work
- Unusual colours or finishes
- Whether we combine several jobs
- Whether it’s a chip, crack, burn or wear
What it costs depends on the type and amount of damage, the material and how many items we do on one visit. We give a fixed price from your photos, so you know the cost before you book.
How to get a fixed quote
Before you send photos, these tips help us give you a firm price:
- Any earlier repairs or coatings
- What it’s made of, if you know
- Daylight if possible, and no flash reflection
- A wider photo showing the whole bath
The quickest way to a price is to send two or three pictures through our quote form or call us. We will say immediately whether it can be repaired.
How the visit works
Arrival times are agreed in advance. Once we are there, the work takes most of the day for most jobs. We leave the room clean and ready to use once it has cured.
- We mask and protect the room and ventilate it.
- The bath is cleaned, degreased and any chips or rust repaired.
- The surface is prepared and a bonding primer applied.
- We spray several coats of new enamel finish.
- Once cured, normally by the next day, the bath is ready.
Before we arrive
- Tell us about any previous repairs or coatings
- Let us know which floor the room is on
- Keep a parking space free if you can
Ask for a price
Send us photos of the damage and a wider shot of the whole item, with your PE7 postcode, and we will come back with a fixed quote.
Advice
Can I fix it myself?
DIY kits are sold for most surfaces, and they can tidy up a tiny mark. The trouble is colour and preparation: they come in a handful of shades, and if the surface isn’t prepared the repair won’t last.
A DIY attempt isn’t a disaster. We remove the old filler and start again, so it doesn’t stop a professional repair. Just mention it when you send photos, as it can add time.
For landlords and businesses
We carry out planned and one-off repairs for housing associations and facilities teams. Repairing in place avoids the disruption of a replacement, which matters when someone is living in the home.
Builders, developers and site managers book us for snagging repairs, putting right damage done during fitting so nothing needs replacing. We’re CHAS, Constructionline and SafeContractor accredited.
About our accreditations · Every repair comes with a one-year guarantee.
