Northumberland · England
Bath Re-enamelling in Waren Mill
Bath re-enamelling in Waren Mill without the cost of replacing. Send us photos for a fixed price, then we come to you.
- Resurfacing from £350
- A coloured bath you want in white
- Lots of chips and rust spots
Landlord and trade work in Waren Mill
Builders, developers and site managers book us for snagging repairs, putting right damage done during fitting so nothing needs replacing. We’re CHAS, Constructionline and SafeContractor accredited.
Hotels, guest houses and holiday lets need rooms back in use quickly, so most of our work is done in a single visit. We can work around your bookings.
Bath re-enamelling at your home in Waren Mill
We re-enamel a lot of period and roll-top baths, which would be difficult and expensive to replace. Doing them in place keeps an original feature. Common call-outs are for enamel that’s lost its shine and feels rough and a peeling or bubbling previous coating, on cast iron baths, basins & shower trays and pressed steel baths.
Every repair is covered by our one-year guarantee, wherever you are in Northumberland.
- Area
- Waren Mill (NE70)
- Area hub
- Northumberland
- Warranty
- One year on every repair
- Quotes
- From £350. Free and fixed, from your pictures
- Telephone
- 0345 017 0787
- Last updated
- 23 October 2026
The process
You don’t need to empty the room. Everything we use comes in the van with us, lay protective sheets and get going once we’ve agreed what we are doing. It generally takes most of the day, and you can get on with other things while we’re there.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures until the day after.
Getting ready for the visit
- Let the surface dry out before the visit
- Keep a parking space free if you can
- Tell us about parking, stairs or access
Getting a price
There’s no need for us to visit first. Nearly every job can be priced from pictures: send a close-up, a wider shot and your postcode, and we’ll reply with a fixed price.
Read more
Materials and what they mean for the repair
Pressed steel
Pressed steel baths take a new finish well, once any rust has been treated. Rust around the waste is common on steel, so we pay close attention there.
Acrylic
We resurface acrylic baths as well, using a system that bonds to acrylic. It must be solid and not flex underfoot for the finish to last.
About Waren Mill
Waren Mill is about 15 miles south-east of Berwick-upon-Tweed, in Northumberland. We travel to clients in Waren Mill and nearby villages, so there is no workshop to go to. Waren Mill is one of 189 places in Northumberland we cover. Our jobs stretch from Waren Mill to Newcastle upon Tyne (about 43 miles away).
Our visits in NE70 are booked in the same way as anywhere else. With the B1342 close by, Waren Mill is easy for our technicians to reach. Other places close to Waren Mill include Burton (2 miles east), Bamburgh (2 miles east), Belford (2 miles west), Middleton (3 miles west) and Warenford (4 miles south). Further out, we also cover Berwick-upon-Tweed (15 miles north-west), Alnwick (14 miles south), Wooler (10 miles west), Seahouses (5 miles east), East Ord (15 miles north-west) and Spittal (14 miles north-west).
Near you in Waren Mill
A little further out are Bamburgh Castle (2.2 miles east) and RNLI Grace Darling Museum (1.9 miles east). Open spaces near Waren Mill include Brada Hill.
When we’d advise against a repair
It helps to know what we can’t do:
- Leaks from fittings rather than the bath
- Anything hidden under an old coating, until we remove it
- A metal bath with a through crack
Not sure? Send pictures and we’ll give you a straight answer before you book.
Surfaces we repair
- Basins & shower trays
- Acrylic baths
- Pressed steel baths
- Victorian roll-tops
- Cast iron baths
Also in Waren Mill
What affects the price in Waren Mill
Prices start from £350. We give every job a fixed quote from pictures. These are the things that affect it:
- Access to the area
- Previous DIY repairs that have to come out
- The material and finish
- Unusual colours or finishes
No two jobs are quite the same, so we price each one individually. What’s damaged, how badly and how easy it is to reach all make a difference, and combining jobs on one visit brings the cost down.
Quotes from your pictures
Good photos mean an accurate price. Here’s what helps:
- A clear, close picture of the problem area
- Any earlier repairs or coatings
- Good light, ideally daylight, without flash glare
- Something in shot to show the size
For most jobs, pictures are all we need to give you a price. Tell us what happened and where you are, and we’ll reply with a fixed quote and the earliest dates we have.
Looking after it afterwards
A little care keeps the finish looking good. Our advice:
- Have chips seen to early
- Fix dripping taps quickly
- Never use suction bath mats
- Rinse off hair dye, oils and bath bombs immediately
Rinse the bath and wipe it over after use, especially in hard water areas, to stop limescale building up.
The longer worn enamel is left, the rougher it gets, and rust spots spread under the surface. Acting earlier keeps the preparation simpler.
Common problems we fix in Waren Mill
By the time a bath is a few decades old, it may have a mix of issues: dull areas, chips, rust and staining. Resurfacing sorts them out together.
Get in touch if you’ve noticed:
- Staining under the taps and around the waste
- A dull, rough surface that won’t come clean
- Wear marks under the taps
- A coating lifting around the plughole
What to look for in a quote
- What protection goes down before work starts
- Who will actually do the work
- When it can be used again
- Is the price fixed, and does it include VAT?
Waren Mill: your questions answered
What areas do you cover?
We cover the entire UK, including Waren Mill and the rest of Northumberland. Just include your postcode and we’ll confirm dates.
What if the damage is worse than the pictures show?
It’s rare, but if it happens we talk to you first. You decide whether to go ahead.
When can you do it?
That depends on our diary for your area. Send pictures with your postcode and we’ll reply with the earliest dates.
Can a failed resurfacing be redone?
Usually, yes. We strip the failing coating and resurface it properly. Tell us about it when you ask for a quote.
Do you charge for travel?
There’s no separate call-out charge. Your fixed price includes everything.
What do you need from me?
Use the quote form or ring 0345 017 0787, and we’ll do the rest.
How long will the bath be out of use?
One day for most baths, ready the next day. We give you timings with the quote.
Is a repair better than a new one?
Generally, if the item is otherwise sound. A repair avoids removal and making good. If replacing would be better, we’ll say so.
DIY kit or professional repair?
It’s tempting to reach for a kit, but the repairs we redo most often are DIY ones that have discoloured or lifted. Doing it properly first is normally the cheaper route.
A DIY attempt isn’t a disaster. We remove the old filler and start again, so it will not stop us repairing it. It does add a little time, so tell us about it when you send pictures.
About our accreditations · Every repair comes with a one-year guarantee.
