Herefordshire · England
Bath Repair in Poolpardon
Chip and crack repairs to enamel, acrylic and cast iron baths for householders, landlords and businesses in Poolpardon. Send photos for a free, fixed quote.
- Repairs from £95
- A chip where the taps sit
- Rust by the waste and overflow
About our bath repair in Poolpardon
Repairing baths is what we do most. A chip by the taps, a crack in the base and a rust spot by the plughole are all repaired in place, normally in one visit. We work on whirlpool & spa baths, cast iron enamel and pressed steel enamel, and common reasons people get in touch are rust spots around the plughole and a chip where the taps sit.
All our work is covered by a one-year guarantee, wherever you are in Herefordshire.
- Where
- Poolpardon (HR3)
- Area hub
- Herefordshire
- Cover
- One year on every repair
- Price
- From £95. Fixed and free, based on photos
- Call
- 0345 017 0787
- Last updated
- 23 October 2026
Repair or replace: which is better?
For damage in one or two places, a repair is the obvious choice. It costs far less than a new bath plus fitting, it takes one visit, and nothing else in the room changes. Prices start from £95. Instead of hourly rates, we price the entire job up front. It depends on the damage, the material and access, and combining items on one visit brings it down.
Why us?
- A year’s guarantee on all work
- Repair technicians who travel to you, UK-wide
- Typically one visit, start to finish
- Colour-matched on site
See our full price list or resurfacing vs replacement cost guide.
Also near Poolpardon
What else we do in Poolpardon
Keeping it looking good
How the surface is treated afterwards matters:
- Protect the bath with a towel when doing jobs nearby
- Keep metal cans and razors off the surface
- Do not scrub with anything abrasive
- Clean with warm water and a mild detergent
Use gentle, non-abrasive cleaners and avoid dropping heavy items on the repaired area. Get any new chip seen to quickly, before rust sets in.
Stop using the bath if a crack lets water through. Water under the bath can damage the floor and the ceiling below.
Repairs by material
Cast iron
A cast iron bath is heavy enough that most people never want to move it. Only the enamel surface wears or chips, and that is the part we put right.
Pressed steel
Pressed steel is thinner and lighter, with an enamel finish like cast iron. Chips rust quickly on steel, especially around the waste, so early repairs matter.
What we can’t put right
A repair is not right for every job, for example:
- Flexing caused by a failed cradle or loose feet
- Leaks from the waste or overflow fittings (a plumber’s job)
- Wear across the whole surface, which needs re-enamelling
Send us photos and we’ll tell you honestly before booking.
Materials we repair
- Acrylic
- Cast iron enamel
- Roll-top & freestanding
- Pressed steel enamel
- Whirlpool & spa baths
Our work in Poolpardon
Poolpardon is about 16 miles west of Hereford, in Herefordshire. We visit clients in Poolpardon, so there is no workshop to go to. Poolpardon is one of 255 places in Herefordshire where we work. Our jobs stretch from Poolpardon to Birmingham (about 56 miles away).
Every address in HR3 is within our area, from the main roads to the quietest streets. Neighbouring places we cover include Priory Wood (1 mile south-west), Whitney-on-Wye (1 mile north-east), Millhalf (2 miles north-east), Brilley (2 miles north) and Winforton (3 miles north-east). We also work in nearby towns such as Newton Farm (15 miles east), Whitecross (15 miles east), Kington (7 miles north), Y Gelli Gandryll (3 miles south-west), Hay (3 miles south-west) and Bobblestock (14 miles east).
Local landmarks in Poolpardon
We visit homes around Clifford Primary School and Church of St Mary. Well-known places in the area include Clifford Castle and Barbican (1 mile west). The countryside around Poolpardon includes Monk's Well Hill.
How the visit works
Expect a friendly, tidy visit. We confirm the time with you beforehand, cover and mask the work area, then carry out the work, which generally takes a few hours. If we find something your pictures didn’t show, we’ll explain it before carrying on.
- We clean the area and remove any loose enamel or rust.
- Next we fill the damage and sand it smooth and level.
- We tint the finish on the day to suit your bath’s shade of white or colour.
- We build up the finish and polish it into the surrounding enamel.
- We leave it to cure; you can normally use the bath the following day.
Preparing for the visit
- Keep children and pets away from the room on the day
- Let us know if it has been repaired before
- Move bottles, mats and clutter away from the area
Ask for a price
No survey visit is needed: we price from photos. Use the quote form, or ring 0345 017 0787 to talk it through, and we’ll come back with a fixed figure.
Advice
Do you need bath repair in Poolpardon?
A cracked acrylic bath normally wasn’t supported properly. Legs that are not adjusted, a missing cradle or a soft floor let the base flex until it cracks.
If you can see any of these, send us a photo:
- A kit repair that didn’t last
- Impact holes in acrylic
- A chipped rim or side
- Damage done while the bathroom was being fitted
What to look for in a quote
- The length of the guarantee and what it covers
- Whether a trained technician does the job
- Whether the colour is mixed to match
- Whether cleaning and preparation are in the price
Landlord and trade work in Poolpardon
Builders use us to fix snagging damage before handover, saving last-minute replacements. We can visit several plots in one trip to keep costs down.
We regularly work with letting and managing agents. Send the address, photos and access details and we will arrange it.
Questions from Poolpardon
Which areas do you work in?
We work UK-wide, so Poolpardon is covered. Our prices are the same everywhere.
Is a bath repair durable?
A properly prepared repair should last a long time, and it’s guaranteed for a year. Gentle cleaning helps it last.
Do I need to be at home?
Yes. The technician needs access to the room for the visit, at a time we agree with you.
Can I add another job to the visit?
Yes. Combining jobs on one visit brings the cost down. Send photos of everything you’d like done.
What about rust by the waste?
Yes, it’s one of the most common repairs we do. The rust is cut back to clean metal and sealed before we fill and finish it.
Is a holed acrylic bath repairable?
Often, if there’s access underneath. We back the hole, fill it and refinish the surface.
Are you a vetted contractor?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
Is the work guaranteed?
Yes, for a year. If there’s a problem with the work in that time, we come back and put it right.
Should I try a DIY kit first?
The difference between a kit and a professional repair is mostly in the preparation and colour. We prepare the area properly, mix the colour on site and polish the finish to match, and the work is guaranteed.
If you do try a kit, read the instructions carefully and work on a clean, dry surface, and give it the full curing time. If it doesn’t work out, we can still repair it properly.
About our accreditations · Every repair comes with a one-year guarantee.
