Liverpool · England
Bath chip & crack repair in Seacombe, Liverpool
Bath repair for Seacombe, without a refit. Send us photos for a fixed price, then we come to you.
- Repairs from £95
- Scuffs and scratches in the surface
- An old repair that has yellowed or come loose
About our bath repair in Seacombe
Repairing baths is what we do most. Chips on the rim, rust around the waste and cracks in acrylic are all fixed without removing the bath, normally in one visit. Our technicians work on whirlpool & spa baths, cast iron enamel and roll-top & freestanding, and common reasons people get in touch are scratches you can feel with a fingernail and chips caused by builders.
A one-year guarantee comes as standard, so you’re not left on your own once we have gone.
- Where
- Seacombe (CH44, CH41, CH27)
- Region
- Liverpool
- Warranty
- One year on every repair
- Quotes
- From £95. Free and fixed, from your pictures
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Should I try a DIY kit first?
Kits are cheap and easy to find, but the repairs we redo most often are DIY ones that have discoloured or lifted. Doing it properly first is normally the cheaper route.
A DIY attempt isn’t a disaster. We take the old repair out and do it properly, so it doesn’t stop a professional repair. Just mention it when you send photos, as it can add time.
Looking after it afterwards
Simple care helps the repair last. We recommend:
- Get any new chip repaired before it rusts
- If an acrylic bath flexes, have its feet adjusted
- A dripping tap stains enamel, so fix it early
- Stick to mild cleaners and a soft cloth
Clean with mild, non-abrasive cleaners and try not to drop heavy bottles on the repair. Deal with new chips early, before rust sets in.
If water is getting through a crack, stop using the bath. Leaks under a bath can damage floors and ceilings.
Landlords, agents and businesses in Seacombe
For developers and builders, we fix damage before handover. Several plots can be done in one visit.
We carry out planned and one-off repairs for housing associations and facilities teams. Repairing in place avoids the disruption of a replacement, which matters when someone is living in the home.
How it works
We begin by going over the job with you. After that, protection goes down around the work area and the work begins. It normally takes a few hours, depending on the damage.
- We start by looking at the damage and confirming the plan with you.
- Loose enamel, rust and dirt are removed so the repair can bond.
- We build up the filler in layers, shaping it to the bath.
- We tint the finish by hand to match the bath.
- The repair is polished to the same gloss as the bath and left to cure.
Before we arrive
- Clear toiletries, mats and anything else from around the area
- Point us to the nearest place to park
- Mention any parking restrictions or tricky access
Ask for a price
No survey visit is needed: we price from photos. Send them through the quote form, or call 0345 017 0787 if you’d rather talk it through, and we’ll come back with a fixed figure.
Advice
Seacombe: your questions answered
Do you work for landlords and businesses?
Yes. We work for landlords, agents, builders and businesses as well as householders across Liverpool.
What information do you need?
A close-up, a wider photo and your postcode. After that, we just agree a date.
Can you repair a failed DIY repair?
Yes. We remove the old filler and start again. Tell us about it when you send photos.
It’s been repaired before. Can you still fix it?
In most cases. We remove the old repair before doing a new one, so let us know about it.
Is my repair covered?
All our work carries our one-year guarantee. We will explain what it covers when we quote.
Can I add another job to the visit?
Yes, and it’s often cheaper. Just add the extra items to your photos and we’ll quote them together.
Are you accredited?
Yes, including CHAS, Constructionline and SafeContractor. See our accreditations page for the full list.
What does bath repair cost?
Repairs from £95. Because every job differs, we price from photos. You know the full cost before anything is booked.
What a repair cannot fix
We’ll always be straight with you, so here’s what a repair won’t do:
- Leaks from the waste or overflow fittings (a plumber’s job)
- Cracks in parts of an acrylic bath we can’t get to from below
- A steel bath rusted through
Send us photos and we’ll tell you honestly.
What we work on
- Acrylic
- Roll-top & freestanding
- Pressed steel enamel
- Cast iron enamel
- Whirlpool & spa baths
Common problems we fix in Seacombe
Acrylic baths that crack nearly always have a support problem. Legs that are not adjusted, a missing cradle or a soft floor let the bath move until the acrylic gives way.
The most common problems we are called about are:
- Rust by the waste and overflow
- A kit repair that didn’t last
- Impact holes in acrylic
- Chips under the taps
Comparing quotes
- Whether the price covers travel
- What protection goes down before work starts
- How soon you can use it again
- How changes to the job are handled
Different materials, different repairs
Composite and resin
Stone resin and composite baths are heavy and solid, and often freestanding. Chips and scratches can be filled and colour matched, in much the same way.
Acrylic
Acrylic baths are moulded sheet reinforced underneath. They do not rust, but they can crack, scratch or be holed, and a crack only stays repaired if it’s supported underneath.
What affects the price in Seacombe
Repairs from £95. Quotes are free and the price is fixed. What we take into account:
- Access to the area
- How many areas need work
- The material and finish
- Previous DIY repairs that have to come out
A repair generally costs much less than people expect, particularly next to the cost of replacement. Photos let us give you the exact figure.
Send photos for a quote
Two or three clear pictures are generally enough. It helps if you send:
- One sharp close-up of the damage
- Whether it’s been repaired or coated before
- A coin or ruler next to the damage for scale
- A picture taken from further back
Ring 0345 017 0787, or send us photos through the quote form. With one close-up and one wider picture, we can give you a fixed price the same day in most cases.
Covering Seacombe
Seacombe is about 1 mile south-east of Wallasey, in Liverpool. Wherever you are in the CH44 postcode area, we come to you. We work in all 52 towns and villages in Liverpool.
Jobs in CH44, CH41 and CH27 are booked in the same way as anywhere else. From Dock Road, Bell Road and Park Road or anywhere nearby, a technician can come to you. With the A59 and A5027 close by, Seacombe is simple for us to get to. Close by, we cover Poulton (1 mile west), Wallasey (1 mile north-west), Egremont (1 mile north), Wallasey Village (2 miles north-west) and Bidston (2 miles west). We also work in nearby towns such as Liverpool (4 miles east), Crosby (5 miles north), Everton (3 miles east), Orrell (4 miles north), Brighton-le-Sands (5 miles north) and Wavertree (4 miles east). Seacombe is among the bigger towns we cover in Liverpool.
Around Seacombe
Our clients here include homes close to The Mona Castle pub, Church of Our Lady Star of the Sea and Central Park, among other places. You will also find Weatherhead High School (1.2 miles west), Kingsway Primary School (within half a mile north-west) and Liscard School of Science and Art (0.6 miles north-west). For rail, the closest station is Birkenhead Park station, about 0.9 miles south-west. Well-known places in the area include Museum of Printing (1.2 miles south-east) and St Paul's (1.4 miles east). The countryside around Seacombe includes New Ferry Butterfly Park and Bidston Hill.
More services for Seacombe
About our accreditations · Every repair comes with a one-year guarantee.
