Highland · Scotland
Bath Re-enamelling for Clachamish homes
Fixed-price bath re-enamelling in Clachamish and the surrounding area, done in a single visit in most cases.
- Resurfacing from £350
- Several chips and rust patches
- An original cast iron bath that needs restoring
Bath re-enamelling at your home in Clachamish
Re-enamelling gives a worn bath a new glossy surface without a refit. It suits baths that are dull, stained, rough or chipped all over. We work on pressed steel baths, basins & shower trays and cast iron baths, and the jobs we see most are a period or roll-top bath worth keeping and brown or grey marks that don’t clean off.
You’re covered for a year from the day of the repair. Just call us if there’s a problem and we will come back.
- Area
- Clachamish (IV51)
- Area hub
- Highland
- Cover
- One year on every repair
- Quote
- From £350. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Page updated
- 23 October 2026
FAQs for Clachamish
When can you do it?
We’ll give you dates with your quote. Tell us if you need it done quickly.
Is there a call-out fee?
No. Our quotes include travel, with the same prices everywhere we work.
Do you cover the whole of Highland?
All of Highland, and the rest of the UK. There’s no extra charge for travel.
How do I book?
Some photos, your postcode and how to reach you. On the day, we only need access to the room.
How do I get a price for bath re-enamelling in Clachamish?
Prices start from £350. We give a fixed price based on photos of the damage. Send a close-up and a photo of the entire item and your postcode.
Can you change the colour of my bath?
Yes, white is the usual choice. Tell us what you’d like when you ask for a quote.
Do you need to take the bath out?
No, it stays where it is. We work on the bath in place, with the room masked and ventilated.
Will the price change on the day?
Your quote covers the damage in the pictures. Anything extra is discussed before we begin.
What happens on the day
We work cleanly and quietly. Protection goes down first, then the work takes the best part of a day. Before we leave, we explain how soon it can be used and how to look after it.
- First we protect the bathroom and set up ventilation.
- We clean and degrease the bath and repair any chips or rust.
- The surface is prepared and a bonding primer applied.
- We spray on the new enamel finish in several coats.
- The bath is left to cure and can normally be used the day after.
How to prepare
- Tell us if there are stairs or a lift
- Keep pets and children out of the room while we work
- Move bottles, mats and clutter away from the area
Get a quote
The quickest way to a price is to send a couple of photos using our quote form or call us. We will say straight away whether it can be repaired.
Related advice
What a repair can’t fix
A repair is not right for every job, including:
- Anything hidden under an old coating, until we remove it
- A cast iron or steel bath that’s cracked right through
- Steel that has corroded right through
Send us photos and we will tell you honestly before you book.
Materials we repair
- Acrylic baths
- Pressed steel baths
- Victorian roll-tops
- Basins & shower trays
- Cast iron baths
For landlords and businesses
Builders use us to fix snagging damage before handover, so there is no need to replace a damaged item at the last minute. We can visit several plots in one trip.
Rented homes see more wear and tear, and replacing things at every changeover adds up. Repairing between tenants keeps the property presentable for less.
About Clachamish
Clachamish is in Highland. Whether you are in the middle of Clachamish or on the outskirts, we offer exactly the same service: a fixed quote, a tidy visit and a guarantee. Our technicians cover all 253 towns and villages in Highland.
Jobs in IV51 are booked in the same way as anywhere else. Nearby, we also work in An t-Aodann Ban (3 miles south-west), Uig (7 miles north), Lonmore (8 miles south-west), Kilmuir (9 miles south-west) and Dunvegan (9 miles south-west). Remote and island addresses take a little more planning, so call us to arrange it.
Around Clachamish
For a walk, there’s Loch Beag.
Common problems we fix in Clachamish
By the time a bath is a few decades old, it may have a mix of issues: worn patches, chips, rust spots and stains. Resurfacing sorts them out together.
Most people get in touch when they notice one of these:
- Several chips and rust patches
- Worn patches where water runs and sits
- An old resurfacing that’s failing
- A roll-top that is seen better days
Comparing quotes
- How your room will be protected
- Whether the price covers travel
- When it can be used again
- How long the guarantee is and what it covers
What bath re-enamelling costs
Prices start from £350. A fixed quote means you know the cost before you book. We take into account:
- Previous DIY repairs that have to come out
- Access to the area
- Whether it’s a chip, crack, burn or wear
- What the surface is made of
Compared with replacing, repairing normally costs far less, because nothing has to be taken out, refitted or made good. The quote lists exactly what you are paying for.
Quotes from your photos
When you take your pictures, a few simple things make all the difference:
- Your postcode, so we can check dates
- A close-up of the damage, in focus
- What it’s made of, if you know
- Whether it’s been repaired or coated before
Getting a quote takes a couple of minutes: photograph the damage, then the whole bath, include your postcode and send them over. What comes back is a fixed price, not a guess.
What else we do in Clachamish
Why repair rather than replace?
For a sound bath, resurfacing costs far less than replacement, once you add removal, plumbing, tiling and decorating to the price of a new bath. It’s also far quicker. Prices start from £350. No two jobs are quite the same, so we price each one individually. What’s damaged, how badly and how easy it is to reach all play a part, and combining jobs on one visit brings the cost down.
Why book with us
- We come to you, anywhere in the UK
- Rooms protected and left tidy
- Same prices wherever you are
- A year’s guarantee on all work
See our full price list or resurfacing vs replacement cost guide.
Materials and what they mean for the repair
Pressed steel
Pressed steel baths take a new finish well, once any rust has been treated. Steel often rusts by the plughole, so we check it carefully.
Cast iron
Re-enamelling suits cast iron baths perfectly. The body lasts for generations; only the enamel wears, so resurfacing gives them a new life.
Aftercare tips
After the repair has cured, a few habits help it last:
- Fix dripping taps quickly
- Wash away dyes and oils after use
- Respect the curing time we give you
- Clean with a soft cloth and mild detergent
Use mild, non-abrasive cleaners, avoid suction bath mats, and do not leave bottles or razors standing on the surface.
Avoid scrubbing a dull bath with abrasive cleaners. It just wears the enamel further.
About our accreditations · Every repair comes with a one-year guarantee.
