Cambridgeshire · England
Bath Re-enamelling in Foul Anchor
Bath re-enamelling for Foul Anchor, without a refit. Get a fixed price from your photos, then book a visit.
- Resurfacing from £350
- A period or roll-top bath worth keeping
- A dull, rough surface that won’t come clean
When to call us in Foul Anchor
By the time a bath is a few decades old, it may have a mix of issues: dull areas, chips, rust and staining. Re-enamelling deals with all of them in one go.
Send us a picture if you notice any of these:
- An original cast iron bath that needs restoring
- Several chips and rust patches
- Worn patches where water runs and sits
- A dull, rough surface that won’t come clean
What your quote should include
- How your room will be protected
- What the guarantee covers, and for how long
- When it can be used again
- Aftercare advice
How we handle bath re-enamelling in Foul Anchor
We resurface cast iron, steel and acrylic baths, including roll-tops and period baths. The finish is sprayed on in several coats over a bonding primer, after the bath has been cleaned, repaired and keyed. Common call-outs are for a roll-top that’s seen better days and chips and rust in more than one place, in basins & shower trays, acrylic baths and pressed steel baths.
A one-year guarantee comes as standard.
- Where
- Foul Anchor (PE13)
- Region
- Cambridgeshire
- Warranty
- A year, on every repair
- Price
- From £350. Free, fixed quote from pictures
- Call
- 0345 017 0787
- Updated
- 23 October 2026
Your questions about bath re-enamelling in Foul Anchor
Can you price it without visiting?
Nearly always. If pictures do not show enough, we will ask for another angle.
Is there a call-out fee?
No. Our quotes include travel, and we charge the same wherever you are.
What does bath re-enamelling cost?
Prices start from £350. Every job gets a fixed price based on pictures of the damage. Send a close-up and a photo of the whole item and your postcode.
Do I need to be at home?
Yes. We need access to the room while we work, at a time we agree with you.
Do you hold any accreditations?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
I rent my home. Can I book you?
Yes. Check with your landlord; we can send the quote to them too.
What areas do you cover?
All of Cambridgeshire, and the rest of the UK. There is no extra charge for travel.
When can you do it?
Your quote comes with available dates. If it’s urgent, say so and we’ll do what we can.
When we’d advise against a repair
Some jobs aren’t right for a repair, for example:
- Steel that has corroded right through
- Damage hidden under a previous coating, until it’s stripped back
- A cast iron or steel bath that is cracked right through
Send us pictures and we’ll tell you honestly before booking.
Materials we repair
- Cast iron baths
- Basins & shower trays
- Victorian roll-tops
- Acrylic baths
- Pressed steel baths
Where we work around Foul Anchor
Foul Anchor is about 5 miles north of Wisbech, in Cambridgeshire. We work in every kind of home, from flats and terraces to detached houses and new builds, as well as offices, shops and holiday lets. Our technicians cover 371 places across Cambridgeshire.
We work across the PE13 postcode area. We also cover the places around Foul Anchor: Tydd Gote (1 mile west), Four Gotes (1 mile south-west), Walpole Marsh (1 mile east), Tydd St Mary (2 miles west) and Ingleborough (2 miles south). Within a short drive, we also cover Wisbech (5 miles south), March (13 miles south), Leverington (4 miles south), Wisbech St Mary (7 miles south-west) and Walsoken (5 miles south).
What’s near Foul Anchor
We visit homes around Church of St Mary, among other places. Other landmarks nearby include North Cambridgeshire Hospital (5 miles south) and Fenland And West Norfolk Aviation Museum (3.8 miles south).
What your bath is made of matters
Roll-top and period baths
We can resurface a roll-top inside and out, with the outside refinished as well.
Pressed steel
Steel baths and trays have a thin metal body under the enamel. Once a chip exposes it, rust follows quickly, so the metal is treated and sealed before the repair.
DIY kit or professional repair?
A DIY attempt isn’t a disaster. We take the old repair out and do it properly, so it doesn’t stop a professional repair. It does add a little time, so tell us about it when you send pictures.
Kits are cheap and easy to find, but the repairs we redo most often are DIY ones that have discoloured or lifted. Doing it properly first is generally the cheaper route.
What happens on the day
Visits start with a quick look at the job together. Then the area is sheeted and masked and the work begins. You can expect it to take the best part of a day, and we’ll tell you if anything changes.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- We repair chips, rust spots and pitting.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures.
Getting ready for the visit
- Ensure the area is dry
- Tell us about any previous repairs or coatings
- Keep pets and children out of the room while we work
How to get a price
No survey visit is needed: we price from photos. Use the quote form, or ring 0345 017 0787 to talk it through, and you’ll get a fixed figure back.
Related advice
Work for landlords and builders
For anyone letting property in or around Foul Anchor, we’ll quote for several properties at once. Send pictures for each one and we will come back with a combined price.
Hotels, guest houses and holiday lets can’t afford rooms out of action for long, so most of our work is done in a single visit. We can work around your bookings.
Should you replace it?
A replacement frequently means several trades over several days. Re-enamelling is one technician, normally one day. Our bath re-enamelling starts from £350. The price reflects the work involved, not where you live. The full price is agreed before you book, with no extras added later.
Why us?
- We’ll tell you if it’s not worth repairing
- We leave the room as we found it
- Typically one visit, start to finish
- Fixed prices from your pictures
Read our prices page or resurfacing vs replacement cost guide.
Nearby places to Foul Anchor
Other services in Foul Anchor
Aftercare tips
How the surface is treated afterwards matters. Here’s what we suggest:
- Fix dripping taps quickly
- Rinse off hair dye, oils and bath bombs immediately
- A quick wipe after use keeps limescale away
- Do not leave a chip unrepaired
A quick rinse and wipe after use helps, especially in hard water areas, so limescale can’t build up.
If a previous coating is starting to peel, do not pick at it. Moisture gets underneath and makes it worse, so have it stripped and resurfaced.
About our accreditations · Every repair comes with a one-year guarantee.
