Kent · England
Bath Re-enamelling for Selling homes
Full bath re-enamelling and resurfacing for householders, landlords and businesses in Selling. Send photos for a free, fixed quote.
- Resurfacing from £350
- Enamel that is lost its shine and feels rough
- Thin, worn enamel in places
About our bath re-enamelling in Selling
The bath stays where it is, so your taps, tiles and plumbing are left alone. Most baths are done in one visit, with the bath ready to use the following day. We work on Victorian roll-tops, basins & shower trays and pressed steel baths, and the jobs we see most are a bath in a colour that no longer suits and an old resurfacing that’s failing.
Peace of mind is built in: each job carries a one-year guarantee, and we will explain exactly what it covers when we quote.
- Where
- Selling (ME13)
- Area hub
- Kent
- Warranty
- One year on every repair
- Quotes
- From £350. Free and fixed, from your photos
- Telephone
- 0345 017 0787
- Last updated
- 23 October 2026
Different materials, different repairs
Acrylic
Acrylic baths can be resurfaced too, using a system that bonds to acrylic. The bath needs to be firm and well supported.
Cast iron
Cast iron baths are the classic candidate for re-enamelling. The body lasts for generations; only the enamel wears, so a new finish makes them look new again.
Honest limits
Some jobs aren’t right for a repair, including:
- Plumbing leaks, which need a plumber
- Problems we cannot see until an old finish comes off
- Steel that has corroded right through
Not sure? Send pictures and we’ll give you a straight answer.
What we work on
- Acrylic baths
- Victorian roll-tops
- Basins & shower trays
- Pressed steel baths
- Cast iron baths
Looking after it afterwards
It’s all simple stuff, just a few sensible habits:
- Do not leave a chip unrepaired
- Clean with a soft cloth and mild detergent
- Repair dripping taps early
- Wash away dyes and oils after use
Rinse the bath and wipe it over after use, especially in hard water areas, so limescale cannot build up.
Rust spots on a worn bath get worse with time and make the job bigger. It’s simpler to resurface before they spread.
Places near Selling
What else we do in Selling
Where we work around Selling
Selling is about 3 miles south-east of Faversham, in Kent. Anywhere in ME13, we come to you. We work in all 922 towns and villages in Kent, from the larger towns to small villages. We work right across the region, from Selling to London (about 47 miles away).
All of ME13 is covered, from the main roads to the quietest streets. From Selling Road, Selling Court and Vicarage Lane or a nearby road, we can come to you. Other places close to Selling include Perrywood (1 mile south), Hogben's Hill (1 mile west), Gushmere (1 mile north), Neames Forstal (1 mile east) and Crouch (1 mile north-east). Within a short drive, we also cover Ashford (9 miles south), Canterbury (7 miles east), Sittingbourne (10 miles north-west), Whitstable (7 miles north-east), Faversham (3 miles north-west) and Herne Bay (11 miles north-east).
What’s near Selling
We visit homes around Selling Church of England Primary School, The White Lion Public House and Church of St Mary, among other places. The closest station to Selling is Selling station, roughly 0.8 miles north-east of the centre. Further afield, we also cover the area around Tower keep castle at Chilham (2.5 miles south-east).
How the visit works
We work cleanly and quietly. We protect the area first, then the work takes a full day. Before we leave, we explain the curing time and the aftercare.
- The room is masked, protected and ventilated.
- Next we degrease the bath and fix chips and rust spots.
- We prepare the surface and apply a bonding primer.
- We spray on the new enamel finish in several coats.
- Once cured, normally by the next day, the bath is ready.
Getting ready for the visit
- Mention any earlier repairs or resurfacing
- Have somewhere for us to park nearby if possible
- Mention any parking restrictions or tricky access
Get a quote
Send us a picture of the damage and a wider shot of the entire item, and tell us you’re in Selling, and we’ll reply with a fixed price.
Advice
Repairing versus replacing in Selling
Replacing a cast iron bath is a big job: it’s very heavy, may need breaking up, and the replacement can be costly. Re-enamelling avoids all of it. Resurfacing from £350, with every job priced individually. Set against the cost of replacement, repairing typically costs far less, because nothing has to be taken out, refitted or made good. Your fixed quote shows exactly what’s included.
Why us?
- A fixed quote before you book
- Honest advice, even when it means no job
- A year’s guarantee on all work
- Generally one visit, start to finish
Read our prices page or guide to resurfacing and replacement costs.
Your questions about bath re-enamelling in Selling
Can you change the colour of my bath?
Yes, most people go for white. Tell us what you’d like when you ask for a quote.
What does bath re-enamelling cost?
Prices start from £350. Every job gets a fixed quote based on photos of the damage. Send a close-up of the damage and a wider photo with your ME13 postcode.
Will it make a mess?
No. The work area is masked and covered, and we leave the room clean.
Is there a smell?
Yes, while we are applying the finish. Ventilation keeps it down, and it fades as the finish cures.
Do I have to be there?
We need someone to let us in. You do not need to watch us work.
Can you do more than one item on the same visit?
Yes. Combining jobs on one visit brings the cost down. Include photos of each item.
What happens if you find more damage?
The price is fixed for what the photos show. If there is more, we will tell you before starting.
I rent my home. Can I book you?
Yes. Check with your landlord; we can send the quote to them too.
For landlords and businesses
Builders, developers and site managers book us for snagging repairs, fixing chips and scratches before handover. We are CHAS, Constructionline and SafeContractor accredited.
We are used to working with agents and managing companies. Send the address, photos and access details.
When to call us in Selling
Older baths frequently have several problems at once: worn patches, chips, rust spots and stains. Resurfacing sorts them out together.
Common reasons people in Selling contact us include:
- Staining under the taps and around the waste
- An outdated colour you’d like to change
- A roll-top that is seen better days
- Worn patches where water runs and sits
Questions to ask before you book
- How changes to the job are handled
- How to look after the finish
- How long the guarantee is and what it covers
- Whether cleaning and preparation are in the price
DIY repairs versus a professional job
What a professional repair adds is preparation, colour matching and finishing. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, then guarantee it for a year.
For a hairline mark somewhere you’ll never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, a professional repair is worth it.
About our accreditations · Every repair comes with a one-year guarantee.
