Cornwall · England
Bath Re-enamelling for St Cleer homes
Full bath re-enamelling and resurfacing in St Cleer, carried out at your home and guaranteed for a year.
- Resurfacing from £350
- A roll-top that’s seen better days
- Wear marks under the taps
Do you need bath re-enamelling in St Cleer?
By the time a bath is a few decades old, it may have a mix of issues: worn patches, chips, rust spots and stains. Re-enamelling deals with all of them in one go.
Most people contact us after spotting one of these:
- Enamel that’s lost its shine and feels rough
- Staining under the taps and around the waste
- A coating lifting around the plughole
- Thin, worn enamel in places
Comparing quotes
- Who turns up on the day
- What happens if the damage is worse than the pictures show
- Whether the colour is mixed to match
- How long it needs to cure
Bath re-enamelling in St Cleer, done in place
We re-enamel a lot of period and roll-top baths, which would be difficult and expensive to replace. Doing them in place keeps an original feature. Typical jobs include an original cast iron bath that needs restoring and a coating lifting around the plughole, across basins & shower trays, cast iron baths and acrylic baths.
We stand behind the work with a one-year guarantee, so you’re not left on your own once we’ve gone.
- Location
- St Cleer (PL14)
- Region
- Cornwall
- Cover
- 12 months on all our work
- Quotes
- From £350. Free, fixed quote from pictures
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
St Cleer and nearby
St Cleer is about 2 miles north of Liskeard, in Cornwall. Jobs in St Cleer are booked in like any other job: a fixed quote from photos, then a visit to do the work. St Cleer is one of 644 places in Cornwall where we work.
Our technicians cover all of PL14. Whether you live on Trethevy Close, Kilmar Way and Well Lane or a nearby road, a technician can come to you. Other places close to St Cleer include Tremar Coombe (1 mile north-east), Tremar (1 mile east), Common Moor (1 mile north-west), Darite (1 mile north-east) and Trembraze (2 miles south). We also work in nearby towns such as Bodmin (11 miles west), Saltash (12 miles south-east), Launceston (11 miles north-east), Looe (9 miles south), Torpoint (14 miles south-east) and Burraton Coombe (12 miles south-east).
Landmarks near St Cleer
We visit homes around Church of St Clarus, Liskeard School and Community College and St Cleer Primary Academy and the streets around them. The nearest railway station is Liskeard station, about 2.8 miles south. Other landmarks nearby include Caradon (2.4 miles south) and Liskeard and District Museum (2.3 miles south). Green spaces nearby include Caradon Hill.
Repair or replace in St Cleer?
A refit takes several trades and several days. Re-enamelling takes one technician and normally one day, with the bath ready the following day. Resurfacing from £350, with every job priced individually. The price depends on the type and amount of damage, what it’s made of and how many items we do on one visit. We give a fixed price from your photos, so there are no surprises on the day.
Why St Cleer clients choose us
- Straight answers about what a repair can do
- Dust sheets down, tidy finish
- Colours mixed by hand to suit your surface
- No need to remove anything
Take a look at our full price list and resurfacing vs replacement cost guide.
Nearby places to St Cleer
Other services in St Cleer
Different materials, different repairs
Acrylic
Acrylic baths can be resurfaced too, using a system that bonds to acrylic. The bath needs to be firm and well supported.
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. Only the enamel surface wears or chips, and that is what we repair.
When we would advise against a repair
In fairness, some problems need a different fix:
- Holes rusted through the metal
- A bath split right through the body
- Problems we can’t see until an old finish comes off
Not sure? Send pictures and we’ll give you a straight answer before booking.
What we work on
- Acrylic baths
- Basins & shower trays
- Cast iron baths
- Victorian roll-tops
- Pressed steel baths
DIY repairs versus a professional job
The difference between a kit and a professional repair is mostly in the preparation and colour. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, then guarantee it for a year.
A kit can be fine for a tiny mark out of sight. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, a professional repair is worth it.
How it works
You don’t need to empty the room. We bring everything we need with us, lay protective sheets and start once you’re happy with the plan. Most jobs take most of the day, and you’re welcome to carry on with your day while we work.
- The room is masked, protected and ventilated.
- The bath is cleaned, degreased and any chips or rust repaired.
- We key the surface and put on a bonding primer.
- We spray several coats of new enamel finish.
- We leave it to cure, and it’s usually ready the next day.
How to prepare
- Keep a parking space free if you can
- Keep pets and children out of the room while we work
- Clear toiletries, mats and anything else from around the area
Get a quote
You don’t need a survey visit. Nearly every job can be priced from photos: we need a close-up, a wider picture and your postcode, and we will come back to you with a fixed figure.
Related advice
Questions from St Cleer
Will there be a smell?
A little, depending on the job. Ventilation keeps it to a minimum.
Does someone need to be in?
We need someone to let us in. You do not need to watch us work.
How soon can you come?
We will give you dates with your quote. Tell us if you need it done quickly.
What happens next?
You will get a fixed quote back, plus dates. There’s no obligation to book.
Can you change the colour of my bath?
Yes. We can resurface a coloured bath in white, and the basin and toilet can be done too.
Can a failed resurfacing be redone?
Typically, yes. We strip the failing coating and resurface it properly. Tell us about it when you ask for a quote.
Can I get a quote without a visit?
Normally, yes. A close-up and a wider photo are enough to give a fixed quote.
Will there be fumes?
Some odour is normal while we spray, so we ventilate the room. It fades as the coating cures.
Looking after it afterwards
It’s all simple stuff:
- Respect the curing time we give you
- Store bottles off the bath
- Wipe the bath dry after use in hard water areas
- Use washing-up liquid and a soft cloth
Dry the bath after use if possible, particularly with hard water, and rinse away any product left on the surface.
Don’t try to scrub a worn bath back to shine. It removes more of the surface.
How we price bath re-enamelling
Prices start from £350. We do not charge extra for travel to St Cleer. The price comes down to:
- How easy the damage is to reach
- Previous DIY repairs that have to come out
- Doing more than one item at once
- The size and number of damaged areas
Most people are surprised how affordable a repair is, particularly next to the cost of replacement. Photos let us give you the exact figure.
Getting a price from pictures
Before you send photos, these tips help us give you a firm price:
- A coin or ruler next to the damage for scale
- Whether it’s been repaired or coated before
- Daylight if possible, and no flash reflection
- The material, if you know it
The quickest way to a price is to send a couple of pictures using our quote form or call us. We will say right away if a repair is the right fix.
About our accreditations · Every repair comes with a one-year guarantee.
