Hampshire · England
Bath Repair in Arford
Bath repair in and around Arford: photo quotes, tidy work and a year’s guarantee.
- Repairs from £95
- A chip where the taps sit
- A kit repair that didn’t last
Repairing versus replacing in Arford
Cast iron baths in particular are worth repairing: they’re very heavy to remove, especially upstairs, and a like-for-like replacement can be expensive. Repairing it leaves it where it is. Repairs from £95, with every job priced individually. It helps to know what pushes a price up or down: access, material, the extent of the damage and whether we can do several items together. Send photos and you will get a fixed figure.
What you get with us
- Dust sheets down, tidy finish
- Honest advice, even when it means no job
- No extra charge for your area
- Nothing taken out or refitted
Read our prices page and bath cost comparison.
Bath repair at your home in Arford
A damaged bath doesn’t have to mean a new bathroom. Our technicians fill, shape and refinish the damage, with the colour mixed on site. We work on cast iron enamel, roll-top & freestanding and whirlpool & spa baths, and people most often call us about damage beneath the taps and chips caused by builders.
The work is covered for a year after we finish. If anything is not right, ring us and we will sort it.
- Where
- Arford (GU35)
- Area hub
- Hampshire
- Cover
- A year, on every repair
- Quote
- From £95. Free and fixed, from your pictures
- Telephone
- 0345 017 0787
- Updated
- 23 October 2026
Questions from Arford
What areas do you cover?
Everywhere in the UK, Arford included. Travel is included in the price.
Can you redo an old repair?
Yes. We take out the old repair and do it properly. Mention it when you send photos.
Can tenants book a repair?
Yes, though it’s best to check with your landlord first. Many landlords are happy for a repair to be arranged before the end of a tenancy.
Can you quote from photos?
Nearly always. If pictures do not show enough, we will ask for another angle.
How long does the repair take to cure?
Normally by the following day, depending on the repair.
Can a cracked acrylic bath be fixed?
Typically, yes, if we can reach the underside to reinforce it. Check under the bath panel, or send us a photo.
Can pets and children be at home?
Yes, as long as they stay out of the room we’re working in. We will let you know when it’s safe to use again.
Are you accredited?
Yes. Our accreditations include CHAS, Constructionline and SafeContractor. The full list is on our accreditations page.
Aftercare tips
Good habits make a big difference to how long a repair lasts:
- Give the bath a quick rinse after use
- Cover the bath during DIY or decorating
- Keep abrasive pads and gritty cleaners away from the bath
- Have new chips seen to early
Leave the repair to cure for as long as we say before running a bath. From then on, mild cleaning is all it needs.
Small chips are quick to repair. Left alone, they stain and can rust, so it’s worth getting them done early.
Landlords, agents and businesses in Arford
Builders, developers and site managers book us for snagging repairs, putting right damage done during fitting so nothing needs replacing. We are CHAS, Constructionline and SafeContractor accredited.
For anyone letting property in or around Arford, we can repair and quote for several addresses together. Send photos for each one and we’ll come back with a combined price.
Repairs by material
Composite and resin
Composite baths are dense and solid, and often freestanding. Chips and scratches are filled and matched, just like other baths.
Pressed steel
Under the enamel of a steel bath is thin metal. Once a chip exposes it, rust follows quickly, so the metal is treated and sealed before the repair.
What a repair cannot fix
It helps to know what we can’t do:
- A steel bath rusted through
- Cracks in acrylic we cannot reach from underneath
- Flexing caused by a failed cradle or loose feet
Send us photos and we will tell you honestly before you book.
What we work on
- Pressed steel enamel
- Whirlpool & spa baths
- Cast iron enamel
- Roll-top & freestanding
- Acrylic
Should I try a DIY kit first?
The difference between a kit and a professional repair is mostly in the preparation and colour. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, then guarantee it for a year.
You can buy a DIY kit for most repairs, and they can make a small mark look better. The trouble is colour and preparation: kits come in a few standard shades, and without proper cleaning and keying the filler often lifts.
The process
A typical visit goes like this: we arrive on time, sheet and mask the area around the job, carry out the work and tidy away. Plan for two to three hours for most chips. Before leaving, we tell you how long to leave it and how to care for it.
- First, we check the damage against your pictures and agree the plan.
- Any rust and loose material comes out, and the area is degreased.
- The damage is filled in layers and shaped to the curve of the bath.
- We tint the finish by hand to match the bath.
- The repair is polished to the same gloss as the bath and left to cure.
Before we arrive
- Let us know about parking or access
- Mention if the room is upstairs or in a flat
- Let the surface dry out before the visit
How to get a price
For a price in Arford, the easiest route is photos: a close-up, a wider shot and your postcode. You’ll get a fixed quote with dates to choose from.
Related advice
Prices and what affects them
Prices start from £95. You will know the full cost before you book. We take into account:
- The colour and finish to match
- The material and finish
- The type of damage
- Doing more than one item at once
A repair is priced on what needs doing, not your postcode. The full price is agreed before booking.
Send pictures for a quote
Photographing the damage takes a minute. Please include:
- Something in shot to show the size
- The postcode, so we can plan the visit
- A picture taken from further back
- Any details about the material
Pricing is simple: snap the damage close up and then the whole item, send them to us with your postcode, and you’ll get a fixed quote back. Quotes are free and no obligation.
Also in Arford
About Arford
Arford is about 6 miles south of Farnham, in Hampshire. Across the GU35 area, we come to you. Arford is one of 683 places in Hampshire we cover. Our jobs stretch from Arford to London (about 41 miles away).
All of GU35 is within our area, from the main roads to the quietest streets. From Beech Hill Road, Arford Common and Headley Hill Road or a nearby road, a technician can come to you. Nearby, we also work in Headley (1 mile south-west), Headley Down (1 mile east), Lindford (1 mile west), Standford (1 mile south-west) and Wishanger Common (2 miles north). We also work in nearby towns such as Farnborough (12 miles north), Fleet (11 miles north), Aldershot (9 miles north), Alton (7 miles west), Petersfield (10 miles south-west) and Yateley (15 miles north).
Near you in Arford
Locally, our jobs take us to homes close to The Holly Bush Inn, Mill Chase Academy and The Holme Church of England Primary School and the streets around them. The closest station to Arford is Liphook station, roughly 3.6 miles south of the centre. A little further out are Chase Community Hospital (2.3 miles south-west). For a walk, there is Deadwater Valley and Gibbet Hill.
About our accreditations · Every repair comes with a one-year guarantee.
