Fife · Scotland

Bath Repair in Dairsie

Problem with your bath in Dairsie? We repair it in place, mix the colour on the day and guarantee the work for a year.

  • Repairs from £95
  • Rust by the waste and overflow
  • Snagging damage from a refit
Surface Doctor technician refinishing the outside of a roll-top bath

Bath repair in Dairsie

Bath repair in Dairsie, done in place

Bath repair is our most common job. A chip by the taps, a crack in the base and a rust spot by the plughole are all repaired in place, normally in one visit. Common call-outs are for rusty patches near the plughole and a failed DIY repair that’s discoloured or lifting, in acrylic, pressed steel enamel and cast iron enamel.

You’re covered for a year from the day of the repair. Just call us if there is a problem and we’ll come back.

Broken acrylic bath corner, rebuilt and refinished (before and after)
Area
Dairsie (KY15)
County
Fife
Warranty
12 months on all our work
Quote
From £95. Fixed and free, based on pictures
Phone
0345 017 0787
Last updated
23 October 2026

Do you need bath repair in Dairsie?

The usual cause is something heavy dropped into the bath, and building work is a common culprit. Cracks in acrylic have a different cause: the bath isn’t properly supported, so it flexes under weight.

Most people get in touch after spotting one of these:

  • Rust spots around the plughole
  • An old repair that has yellowed or come loose
  • Impact holes in acrylic
  • Hairline or through cracks in acrylic

Comparing quotes

  • A fixed quote, and whether VAT is included
  • What prep work is covered
  • Whether a trained technician does the job
  • What protection goes down before work starts

10 questions to ask before you book

Prices and what affects them

Prices start from £95. Prices are worked out job by job. What matters most is:

  • What kind of damage it is
  • How easy the damage is to reach
  • How many items we do on one visit
  • What the surface is made of

Instead of hourly rates, we price the entire job up front. Damage, material and access decide it, and combining items on one visit brings it down.

Send pictures for a quote

When you take your pictures, a few simple things make all the difference:

  • Any earlier repairs or coatings
  • Your postcode, so we can check dates
  • A close-up of the damage, in focus
  • Daylight if possible, and no flash reflection

The quickest way to a price is to send a couple of pictures using our quote form or ring us. We’ll say right away whether it can be repaired.

Covering Dairsie

Dairsie (Gaelic: Osnaburgh) is about 9 miles south of Dundee, in Fife. Our repair technicians come to clients in Dairsie, so nothing has to leave your home. Our repair technicians cover all 133 towns and villages across Fife. We work right across the region, from Dairsie to Edinburgh (about 29 miles away).

Here we cover the KY15 postcode area. From Main Street, Station Road and Osnaburgh Court or anywhere nearby, we can come to you. We also cover the places around Dairsie: Balmullo (2 miles north), Guardbridge (2 miles north-east), Pitscottie (3 miles south), Strathkinness (3 miles east) and Lucklawhill (3 miles north). Larger places within reach include Glenrothes (13 miles south-west), Leven (10 miles south), St Andrews (6 miles east), Methil (11 miles south), Newport-on-Tay (6 miles north) and Anstruther (13 miles south-east).

Near you in Dairsie

In Dairsie, that means homes near Dairsie Free Church. The nearest railway station is Leuchars station, about 3 miles north-east of the centre. Further afield, we also cover the area around St Andrews Community Hospital (5.7 miles east) and Fife and Forfar Yeomanry Museum (2.7 miles south-west).

Map of Dairsie © OpenStreetMap contributors

The process

We work cleanly and quietly. We protect the area first, then the work takes a morning or an afternoon. Before we leave, we explain the curing time and the aftercare.

  1. We clean the area and remove any loose enamel or rust.
  2. We fill the damage and sand it flush with the surrounding surface.
  3. We mix the colour on the day to match your bath’s exact shade.
  4. We apply the finish coats and polish the repair so it blends in.
  5. The repair is left to cure, and most baths can be used the next day.

Before we arrive

  • Ensure the room can be ventilated
  • Tell us about parking, stairs or access
  • Mention any earlier repairs or resurfacing

How to get a price

Call 0345 017 0787 or use the quote form. With a clear picture of the damage and one of the entire bath, we can price the job without visiting.

Send photos for a quote

Advice

Dairsie questions

Is a bath repair permanent?

A properly prepared repair should last a long time, and it’s guaranteed for a year. Gentle cleaning helps.

What about rust by the waste?

Yes, very often. The rust is cut back to clean metal and sealed before we fill and finish it.

Can a cracked acrylic bath be fixed?

In most cases. We reinforce the crack from behind, then fill and refinish the front, so access behind the panel is important.

Do I have to be there?

Yes. We need access to the room while we work, at a time we agree with you.

Is it messy?

Dust sheets and masking go down before we start, and tidy up before we leave.

What happens next?

We review the pictures and send a fixed quote.

Do you repair coloured baths?

Yes, we match coloured baths too. The colour is tinted by hand on the day.

Can landlords book you?

We do, regularly. We quote for multiple addresses and fit around tenancy changeovers.

When a repair isn’t the answer

We will not take on work that will not last, so these are the limits:

  • Cracks in acrylic we cannot reach from underneath
  • A whole bath that’s dull or worn, where a full re-enamel is the better fix
  • A steel bath rusted through

Send us photos and we will tell you honestly before booking.

Materials we repair

  • Pressed steel enamel
  • Cast iron enamel
  • Roll-top & freestanding
  • Acrylic
  • Whirlpool & spa baths

Materials and what they mean for the repair

Composite and resin

Stone resin and composite baths are heavy and solid, and frequently freestanding. Chips and scratches are filled and matched, in much the same way.

Cast iron

Cast iron baths are so heavy that repairing in place makes obvious sense. Only the enamel surface wears or chips, and that’s what we repair.

Can I fix it myself?

It’s tempting to reach for a kit, but the repairs we redo most frequently are DIY ones that have discoloured or lifted. Doing it properly first is generally the cheaper route.

For a hairline mark somewhere you’ll never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, it’s worth having it done properly.

Work for landlords and builders

Hospitality businesses need rooms back in use quickly, so most of our work is done in a single visit. We can work around your bookings.

For anyone letting property in or around Dairsie, we will quote for several properties at once. Send photos for each one and we’ll price them together.

Aftercare tips

Most damage we see is avoidable. These habits help:

  • Put a towel in the bath if you’re working above it
  • Rinse it down after each bath
  • Clean with warm water and a mild detergent
  • Get a dripping tap fixed promptly

Look after the repair the same way as the bath: a soft cloth and washing-up liquid is all it needs. Keep scouring pads and gritty cleaners away from it.

Small chips are quick to repair. Leave them and they collect dirt, stain and, on metal baths, rust, so early repair saves time and money.

CHAS accredited contractor and Constructionline logos SafeContractor, SMAS Worksafe and Builder’s Profile logos

About our accreditations · Every repair comes with a one-year guarantee.

Read what customers say about us on Trustpilot.