Shropshire · England
Bath Repair for Fauls homes
Damaged bath in Fauls? We put it right where it is, match it on site and guarantee the work for a year.
- Repairs from £95
- Snagging damage from a refit
- Deep scratches in acrylic
Questions from Fauls
Is a repair better than a new one?
Generally, when the rest is in good condition. Repairing avoids the cost and disruption of replacing. If replacing would be better, we will say so.
When can I have a bath again?
Typically within a day, though it depends on what we have done.
Do the materials smell?
It depends on the job, but frequently a little. Open windows and an extractor fan help.
Is a cracked acrylic bath repairable?
Normally, yes, as long as we can get to the back of the crack to support it. Check under the bath panel, or send us a picture.
Is the work guaranteed?
Yes: twelve months. If anything goes wrong with the repair within the year, we return to fix it.
Can you quote from photos?
In nearly every case. If photos do not show enough, we’ll ask for another angle.
Can you fix rust around the plughole?
Yes. We take out the rust and any loose enamel, seal and fill the area, then colour-match the finish.
Can you redo someone else’s repair?
Yes, we frequently do. Removing the old work can add time, and that’s in the quote.
How we handle bath repair in Fauls
Whether your bath is steel, cast iron or acrylic, we can repair it. Each material is repaired a little differently: metal baths need any rust dealt with first, and acrylic cracks need support from behind. We are frequently asked to fix deep scratches in acrylic and rusty patches near the plughole, on roll-top & freestanding, acrylic and pressed steel enamel.
Every repair is covered by our one-year guarantee, wherever you are in Shropshire.
- Where
- Fauls (SY13)
- Region
- Shropshire
- Warranty
- A year, on every repair
- Price
- From £95. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
DIY kit or professional repair?
What a professional repair adds is preparation, colour matching and finishing. We prepare the area properly, mix the colour on site and polish the finish to match, then guarantee it for a year.
A DIY attempt isn’t a disaster. We remove the old filler and start again, so it does not stop a professional repair. Just mention it when you send photos, as it can add time.
Should you replace it?
If the rest of the bath is in good condition, a repair is almost always the better choice. It costs less, takes less time and causes far less upheaval, and you keep the bath you chose. If the whole surface is worn, re-enamelling may make more sense, and we will tell you. Our bath repair starts from £95. The price reflects the work involved, not your postcode. You’ll see the full price before booking.
Why us?
- Most jobs done in one visit
- Rooms protected and left tidy
- No extra charge for your area
- Straight answers about what a repair can do
Read our prices page or resurfacing vs replacement cost guide.
Common problems we fix in Fauls
Nearly all the chips we see start with something being dropped: a shampoo bottle, a shower head, a tile or a tool during a refit. On enamelled baths, a chip that reaches the metal lets water in, and rust follows.
These are the problems we are asked about most:
- Chips along the edge of the bath
- Holes from dropped items
- A chip where the taps sit
- Rusty patches near the plughole
Questions to ask before booking
- What happens if the damage is worse than the pictures show
- If travel is included in the price
- What preparation is included
- Is the price fixed, and does it include VAT?
Repairs by material
Acrylic
Acrylic feels warm and is light, but it relies on good support. Cracks are strengthened from behind before the front is finished.
Pressed steel
Under the enamel of a steel bath is thin metal. Once a chip exposes it, rust follows quickly, so we treat and seal the metal before filling.
Honest limits
A few problems are outside what a surface repair can do:
- Wear across the whole surface, which needs re-enamelling
- Cracks in acrylic we cannot reach from underneath
- Flexing caused by a failed cradle or loose feet
Not sure? Send photos and we’ll give you a straight answer before you book.
What we work on
- Pressed steel enamel
- Cast iron enamel
- Whirlpool & spa baths
- Acrylic
- Roll-top & freestanding
Where we work around Fauls
Fauls is about 5 miles west of Market Drayton, in Shropshire. Whether you are in the middle of Fauls or on the outskirts, we offer exactly the same service: a fixed price, a tidy visit and a guarantee. Fauls is one of 433 places in Shropshire where we work. We work right across the region, from Fauls to Liverpool (about 38 miles away).
Jobs in SY13 are booked in the same way as anywhere else. We also cover the places around Fauls: Darliston (1 mile north-west), Prees Wood (2 miles west), Prees Green (2 miles south-west), Prees (2 miles west) and Weston-under-Redcastle (3 miles south-west). Further out, we also cover Shrewsbury (14 miles south-west), Market Drayton (5 miles east), Coleham (14 miles south-west), Kingsland (14 miles south-west), Whitchurch (6 miles north-west) and Belle Vue (14 miles south-west).
Near you in Fauls
We visit homes around Lower Heath CofE Primary School and Church of Immanuel and the streets around them. The nearest railway station is Prees station, about 3.3 miles west of the centre. Further afield, we also cover the area around Red Castle (2.4 miles south-west). The countryside around Fauls includes Prees Heath Common and Hawk Lake.
What affects the price in Fauls
Repairs from £95. There is no charge for travel to Fauls. The price depends on:
- The colour and finish to match
- Doing more than one item at once
- How easy the damage is to reach
- The material and finish
Most people are surprised how affordable a repair is, especially compared with replacing and refitting. Send pictures and we’ll give you the exact figure.
How to get a fixed price
Good photos mean an accurate price. Here’s what helps:
- What it’s made of, if you know
- Something in shot to show the size
- Where you are, by postcode
- Any earlier repairs or coatings
The quickest way to a price is to send a couple of photos through our quote form or call us. We will tell you honestly whether it can be repaired.
The process
It’s a tidy, low-fuss visit. We agree the arrival time in advance, protect the area, and get on with the job, which usually takes a few hours, depending on the damage. If anything looks different from your pictures, we’ll talk to you before going ahead.
- We protect the bath and the floor around it.
- We clean, key and degrease the damage, and any rust is treated.
- We fill it, let it set, then sand it flush.
- We match both the colour and the shine.
- We clear up and give you the curing time, normally until the day after.
Preparing for the visit
- Mention if the room is upstairs or in a flat
- Let us know if it has been repaired before
- Make sure the room can be ventilated
Get a quote
Most clients in Fauls get their price from photos. Tell us what happened and where you are, and we will send back a fixed quote and some dates.
Advice
Landlord and trade work in Fauls
If you manage property in Fauls, we can repair and quote for several addresses together. Just send photos for each address and we will come back with a combined price.
Hospitality businesses cannot afford rooms out of action for long, so we keep visits short and tidy. We can work around your bookings.
Towns and villages near Fauls
What else we do in Fauls
About our accreditations · Every repair comes with a one-year guarantee.
