Shropshire · England
Bath Repair in Garmston
Chip and crack repairs to enamel, acrylic and cast iron baths for homeowners, landlords and businesses in Garmston. Send pictures for a free, fixed quote.
- Repairs from £95
- An old repair that has yellowed or come loose
- A hole punched through by something heavy
Questions from Garmston
How much does bath repair cost in Garmston?
Repairs from £95. The exact price depends on the damage, so we quote from pictures. You know the full cost before anything is booked.
Will you leave a mess?
Very little mess: we sheet and mask everything nearby, and we take our waste away with us.
Can a cracked acrylic bath be fixed?
Usually, yes, as long as we can get to the back of the crack to support it. Take off the bath panel and check, or send us a picture.
Is a bath repair permanent?
Yes, if it’s prepared properly and the bath is sound. It’s covered by our one-year guarantee.
Will the price change on the day?
It’s rare, but if it happens we talk to you first. The price only changes if you agree.
Can you quote from photos?
Normally, yes. Clear photos let us give you a fixed quote without visiting.
Can landlords book you?
We do, regularly. We quote for multiple addresses and fit around tenancy changeovers.
Can you repair a hole in a bath?
Often, if there’s access underneath. The hole is backed, filled and refinished to match.
How we handle bath repair in Garmston
Whatever has happened to the bath, we aim for the same result: a repair that is smooth, sound and hard to spot. Proper preparation, careful filling and shaping, then colour and gloss matching so it sits flush with the rest of the bath. Our repair technicians work on acrylic, cast iron enamel and whirlpool & spa baths, and people most frequently call us about chips on the rim or sides and holes from dropped items.
Big or small, it’s backed by a one-year guarantee.
- Area
- Garmston (SY5)
- Area hub
- Shropshire
- Warranty
- One year on every repair
- Price
- From £95. Free, fixed price from pictures
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
What affects the price in Garmston
Prices start from £95. Prices are worked out job by job, from your photos. What matters most is:
- Whether old repairs or coatings need taking off
- Whether it’s a chip, crack, burn or wear
- How many items we do on one visit
- How much damage there is
Rather than charging by the hour, we price the whole job up front. Damage, material and access decide it, and combining items on one visit brings it down.
Send pictures for a quote
You can typically get a fixed price without us visiting. To make it quick:
- A clear, close picture of the problem area
- A photo taken from further back
- Any earlier repairs or coatings
- Daylight if possible, and no flash reflection
Getting a price is easy: snap the damage close up and then the whole item, send them over with your postcode, and you will get a fixed price back. There is no charge for the quote and you’re under no obligation.
What we’re called out for in Garmston
Rust usually starts where water sits, around the waste, under the taps or in an old chip. Once water reaches the steel or iron, rust spreads under the enamel.
Look out for any of the following:
- An old repair that has yellowed or come loose
- Damage done while the bathroom was being fitted
- Damage beneath the taps
- Chips on the rim or sides
Questions to ask before you book
- Whether the price is fixed and includes VAT
- Whether the price covers travel
- How long the guarantee is and what it covers
- What prep work is covered
Honest limits
A few problems are outside what a surface repair can do:
- A bath that moves underfoot, until its support is fixed
- Cracks in acrylic we can’t reach from underneath
- A bath worn all over, where resurfacing makes more sense
Not sure? Send photos and we will give you a straight answer before booking.
Materials we repair
- Cast iron enamel
- Pressed steel enamel
- Roll-top & freestanding
- Acrylic
- Whirlpool & spa baths
Looking after it afterwards
Aftercare is simple, and it makes a real difference:
- Stick to mild cleaners and a soft cloth
- Don’t leave a fresh chip for long
- Give the bath a quick rinse after use
- Do not scrub with anything abrasive
Clean with mild, non-abrasive cleaners and avoid dropping heavy items on the repaired area. Get any new chip seen to quickly, before rust sets in.
A chip on a metal bath shouldn’t be left. Water gets to the metal and rust starts, turning a quick repair into a bigger one.
What your bath is made of matters
Cast iron
Cast iron is heavy and rigid, finished with fired enamel. Chips can rust if left, but the bath itself lasts for generations, so it’s always worth repairing.
Pressed steel
Pressed steel is thinner and lighter, with an enamel finish like cast iron. Chips rust quickly on steel, especially around the waste, so repair chips early.
Also near Garmston
More services for Garmston
What happens on the day
On the day, we arrive at the time we have agreed, cover the area with dust sheets and masking, and set to work. The job generally takes a few hours, depending on the damage. We tidy up before we leave and tell you when it’s ready to use.
- Dust sheets and masking go down around the bath.
- We clean, key and degrease the damage.
- Filler goes in and is sanded flush once it has set.
- We match both the colour and the shine.
- We tidy up and tell you when the bath can be used, usually the day after.
Getting ready for the visit
- Avoid using the area for a few hours before we arrive
- Make sure the room can be ventilated
- Clear toiletries, mats and anything else from around the area
Ask for a price
Getting a quote takes a couple of minutes: photograph the damage, then the whole bath, include your postcode and send them over. You will get a fixed price, not an estimate.
Advice
Can I fix it myself?
The difference between a kit and a professional repair is mostly in the preparation and colour. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, then guarantee it for a year.
If you’re set on a kit, follow its instructions closely, make sure the area is clean and completely dry, and don’t use it until it has fully cured. If it does not work out, we can still repair it properly.
Work for landlords and builders
Builders, developers and site managers book us for snagging repairs, fixing chips and scratches before handover so nothing needs replacing. We hold CHAS, Constructionline and SafeContractor accreditations.
For anyone letting property in or around Garmston, we’ll quote for several properties at once. Send photos for each one and we will price them together.
Our work in Garmston
Garmston is about 6 miles south-west of Telford, in Shropshire. Book a date that suits you, and you’ll know when to expect us, so there is no waiting around. Our technicians cover 433 places in Shropshire, from the larger towns to small villages. Our nearest city page is Birmingham, about 32 miles away.
Every address in SY5 is covered. We also travel to Eaton Constantine (1 mile west), Leighton (1 mile south-east), Buildwas (2 miles south-east), Little Wenlock (3 miles east) and Homer (3 miles south). We also work in nearby towns such as Shrewsbury (8 miles north-west), Madeley (6 miles east), Bridgnorth (11 miles south-east), Coleham (8 miles north-west), Kingsland (8 miles north-west) and Belle Vue (8 miles north-west).
Landmarks near Garmston
Typical jobs here are in homes near Church of St Mary, among other places. Garmston’s nearest station is Wellington (Shropshire) station, roughly 4.4 miles north-east of the centre. Nearby you will also find Wroxeter Roman Site And Museum (3.1 miles north-west) and Charlton Castle (3.2 miles north). The countryside around Garmston includes The Ercall.
About our accreditations · Every repair comes with a one-year guarantee.
