Bath and North East Somerset · England

Bath Repair in Locksbrook

We travel to Locksbrook for chip and crack repairs to enamel, acrylic and cast iron baths. Nothing is taken out, and the work is guaranteed.

  • Repairs from £95
  • Rust by the waste and overflow
  • Hairline or through cracks in acrylic
Surface Doctor technician refinishing the outside of a roll-top bath

Book bath repair in Locksbrook

Where we work around Locksbrook

Locksbrook is about 1 mile west of Bath, in Bath and North East Somerset. Whether you’re in the middle of Locksbrook or on the outskirts, the service is the same: a fixed quote, a tidy visit and a guarantee. Locksbrook is one of 136 places in Bath and North East Somerset we cover. Our jobs stretch from Locksbrook to Birmingham (78 miles away).

Every address in BA2 and BA1 is within our area, from the main roads to the quietest streets. From May Lane, Park Road and Lyme Road or anywhere nearby, a technician can come to you. Locksbrook is on the A3604, which makes it straightforward to reach. Close by, we cover Newbridge (1 mile north-west), Lower Weston (1 mile east), Twerton (1 mile south-west), Westmoreland (1 mile south-east) and Kingsmead (1 mile east). Further out, we also cover Keynsham (5 miles west), Paulton (7 miles south-west), Peasedown St John (5 miles south), Saltford (3 miles north-west), Batheaston (4 miles north-east) and Timsbury (5 miles south-west).

Near you in Locksbrook

In Locksbrook, that means homes near Parade Gardens, Newbridge Primary School and The Locksbrook Inn and the streets around them. Also close by are City of Bath Technical School (1.3 miles east), Emmanuel Church (within half a mile north-west), Oldfield School (0.9 miles north-west) and Bath Royal Literary and Scientific Institution (1.1 miles east). The nearest railway station is Oldfield Park station, roughly 0.5 miles south-east. Other landmarks nearby include No. 1 Royal Crescent (1 mile east) and Midford Castle (2.9 miles south-east).

Map of Locksbrook © OpenStreetMap contributors

Bath repair in Locksbrook without replacing anything

Bath repair is our most common job. Chips on the rim, rust around the waste and cracks in acrylic are all repaired in place, normally in a single visit. We regularly repair cast iron enamel, roll-top & freestanding and pressed steel enamel, and people most frequently call us about scuffs and scratches in the surface and a kit repair that didn’t last.

The work is covered for a year after we finish. If anything isn’t right, ring us and we will sort it.

Location
Locksbrook (BA2, BA1)
County
Bath and North East Somerset
Cover
A year, on every repair
Price
From £95. Free and fixed, from your photos
Call
0345 017 0787
Updated
23 October 2026
Bath enamel chip by the waste, filled and colour matched (before and after)

FAQs for Locksbrook

What happens after I send pictures?

You get a fixed quote and available dates. If we need another angle, we will ask.

Can you price it without visiting?

Nearly always. If photos do not show enough, we’ll ask for another angle.

How do I get a price for bath repair in Locksbrook?

Repairs from £95. Because every job differs, we price from pictures. You will get a fixed figure before you book.

What areas do you cover?

Everywhere in the UK, Locksbrook included. There’s no extra charge for travel.

Can you redo an old repair?

Regularly. The old material comes out, any rust is treated, then we repair it properly.

Is my repair covered?

Yes: twelve months. If there’s a problem with the work in that time, we come back and put it right.

When can you do it?

Your quote comes with available dates. If it’s urgent, say so and we’ll do what we can.

Can you repair a chip on a coloured bath?

Yes, coloured baths are no problem. We tint the finish to your bath on site.

What we do, step by step

We begin by going over the job with you. Next, we cover and mask everything nearby and we start. It normally takes two to three hours for most chips, and we will keep you posted as we go.

  1. First, the area is cleaned and any loose enamel or rust is removed.
  2. We fill the damage and sand it flush with the surrounding surface.
  3. We tint the finish on the day to suit your bath’s shade of white or colour.
  4. We apply the finish coats and polish the repair so it blends in.
  5. Once it has cured, generally by the next day, the bath is ready to use.

How to prepare

  • Tell us about parking, stairs or access
  • Make sure the room can be ventilated
  • Mention if the room is upstairs or in a flat

How to get a price

We price from photos so you don’t have to wait in for a survey. Send them through the quote form, or call 0345 017 0787 if you’d rather talk it through, and you will get a fixed figure back.

Send photos for a quote

Advice

Do you need bath repair in Locksbrook?

Rust tends to begin where water collects, around the waste, under the taps or in an old chip. Water on bare metal causes rust that creeps under the surrounding enamel.

The most common problems we are called about are:

  • Hairline or through cracks in acrylic
  • Damage beneath the taps
  • Rust spots around the plughole
  • An old repair that has yellowed or come loose

Before booking anyone

  • What happens if the damage is worse than the photos show
  • Whether there are any call-out or travel charges
  • Who will actually do the work
  • The length of the guarantee and what it covers

10 questions to ask before you book

Aftercare tips

A little care keeps the finish looking good. Our advice:

  • Ensure an acrylic bath is firm underfoot
  • Rinse the bath after use, especially in hard water areas
  • Have new chips seen to early
  • Don’t leave razors or cans standing in the bath

Clean with mild, non-abrasive cleaners and try not to drop heavy bottles on the repair. Get any new chip seen to quickly, before rust can start.

Do not leave a chip on a steel or cast iron bath. Once water reaches the metal, rust begins, turning a quick repair into a bigger one.

How we price bath repair

Prices start from £95. You’ll know the full cost before you book. We take into account:

  • The material and finish
  • How much damage there is
  • The type of damage
  • Access to the area

A few things move the price: the amount of damage, the material, access to the area, and how many jobs we do in one trip. Send pictures and you will get a fixed figure.

Send photos for a quote

Most quotes are done from pictures alone. To help us price it:

  • What it’s made of, if you know
  • Details of any past repairs
  • Natural light rather than flash
  • Your postcode, so we can check dates

To get a price, send a couple of pictures through our quote form or call us. We’ll say immediately if a repair is the right fix.

Should you replace it?

For damage in one or two places, a repair is the obvious choice. It costs far less than a new bath plus fitting, it takes one visit, and the bathroom stays exactly as it is. Prices start from £95. Every job is a little different, so each one is priced on its own. What’s damaged, how badly and how easy it is to reach all play a part, and doing several things on one visit costs less than separate visits.

Why Locksbrook customers choose us

  • Most jobs done in one visit
  • No extra charge for your area
  • We leave the room as we found it
  • Colour-matched on site

Take a look at our prices page or resurfacing vs replacement cost guide.

Should I try a DIY kit first?

We understand the appeal of fixing it yourself. The trouble is that kit repairs often look fine at first and then fail, and then the old filler has to be removed first.

DIY kits are sold for most surfaces, and they can tidy up a tiny mark. The trouble is colour and preparation: they come in a handful of shades, and if the surface isn’t prepared the repair will not last.

For landlords and businesses

We also carry out snagging repairs for builders and developers, putting right damage done during fitting. We hold CHAS, Constructionline and SafeContractor accreditations.

Rented homes see more wear and tear, and replacing things at every changeover adds up. Repairing between tenants keeps the property presentable for less.

Repairs by material

Composite and resin

Stone resin and composite baths are heavy and solid, and frequently freestanding. Chips and scratches are filled and matched, in much the same way.

Cast iron

Cast iron baths are so heavy that repairing in place makes obvious sense. Only the enamel surface wears or chips, and that is what we repair.

CHAS accredited contractor and Constructionline logos SafeContractor, SMAS Worksafe and Builder’s Profile logos

About our accreditations · Every repair comes with a one-year guarantee.

Read what customers say about us on Trustpilot.