Derbyshire · England
Bath chip & crack repair in Moorend, Derbyshire
We travel to Moorend for chip and crack repairs to enamel, acrylic and cast iron baths. Nothing is taken out, and the work is guaranteed.
- Repairs from £95
- Chips on the rim or sides
- A chip where the taps sit
Bath repair in Moorend without replacing anything
Repairing baths is what we do most. Chips on the rim, rust around the waste and cracks in acrylic are all repaired in place, normally in one visit. We’re often asked to fix rust by the waste and overflow and a failed DIY repair that’s discoloured or lifting, across roll-top & freestanding, whirlpool & spa baths and pressed steel enamel.
The work is covered for a year after we finish. If anything isn’t right, ring us and we’ll come back.
- Area
- Moorend (DE6)
- County
- Derbyshire
- Warranty
- 12 months on all our work
- Price
- From £95. Free and fixed, from your pictures
- Call
- 0345 017 0787
- Updated
- 23 October 2026
Can I fix it myself?
A DIY attempt is not a disaster. We remove the old filler and start again, so it will not stop us repairing it. It does add a little time, so tell us about it when you send pictures.
Kits are cheap and easy to find, but many of the jobs we do start with putting right a DIY repair. Getting it right first time is generally cheaper.
What a repair can’t fix
Some jobs aren’t right for a repair, for example:
- Leaks from the waste or overflow fittings (a plumber’s job)
- A whole bath that’s dull or worn, where a full re-enamel is the better fix
- Rust that has eaten right through a steel bath
If in doubt, send photos and we’ll say what we think before booking.
Surfaces we repair
- Whirlpool & spa baths
- Roll-top & freestanding
- Pressed steel enamel
- Acrylic
- Cast iron enamel
Keeping it looking good
Nothing complicated is needed, just a few sensible habits:
- Keep abrasive pads and gritty cleaners away from the bath
- Give the bath a quick rinse after use
- Cover the bath during DIY or decorating
- Get any new chip repaired before it rusts
Keep metal objects like razors and cans off the surface, because they can mark the enamel. And fix dripping taps promptly.
If an acrylic bath has a crack, stop showering in it until it’s repaired. Every use opens the crack a little more, and water can get through to the floor below.
When to call us in Moorend
The usual cause is something heavy dropped into the bath, and building work is a common culprit. Cracks in acrylic have a different cause: the bath isn’t properly supported, so it flexes under weight.
Send us a picture if you notice any of these:
- Damage done while the bathroom was being fitted
- Holes from dropped items
- A kit repair that didn’t last
- Chips along the edge of the bath
Comparing quotes
- Whether the price is fixed and includes VAT
- Whether a trained technician does the job
- How soon you can use it again
- Aftercare advice
Repair or replace: which is better?
Replacing a fitted bath normally involves a plumber, removing the old bath, re-tiling and a new panel and disposing of the old one. A repair fixes just the damaged area in one visit. Repairs from £95, with every job priced individually. What it costs depends on how much damage there is and what kind, the material and how many items we do on one visit. You get a fixed price from your pictures, so you know the cost before you book.
Why choose Surface Doctor in Moorend
- We leave the room as we found it
- Everything repaired in place
- We come to you, anywhere in the UK
- No extra charge for your area
See our prices page and bath cost comparison.
How the visit works
It’s a tidy, low-fuss visit. We agree the arrival time in advance, cover and mask the work area, and get on with the job, which normally takes two to three hours for most chips. If anything looks different from your photos, we’ll talk to you before going ahead.
- We start by looking at the damage and confirming the plan with you.
- Any rust and loose material comes out, and the area is degreased.
- We build up the filler in layers, shaping it to the bath.
- We tint the finish by hand to match the bath.
- Finally, it’s polished to match the shine and left to cure.
Preparing for the visit
- Let the surface dry out before the visit
- Let us know about parking or access
- Keep pets and children out of the room while we work
Getting a price
No survey visit is needed: we price from photos. Send them through the quote form, or call 0345 017 0787 if you’d rather talk it through, and we’ll come back with a fixed figure.
Advice
Questions from Moorend
Can I get a quote without a visit?
Normally, yes. Clear photos let us give you a fixed price without visiting.
How long does the repair take to cure?
Usually within a day, though it depends on what we’ve done.
What does bath repair cost?
Prices start from £95. Because every job differs, we price from photos. You’ll get a fixed figure before booking.
What happens once I’ve sent pictures?
We check the damage, the material and your postcode, then reply with a quote.
Can you repair a crack in an acrylic bath?
In most cases. We reinforce the crack from behind, then fill and refinish the front, so we need access under the bath.
It’s been repaired before. Can you still fix it?
Yes, we frequently do. It can add a little time, which we include in the quote.
Something went through my bath. Can it be fixed?
Normally. Send us a photo of the hole and one from under the bath if you can.
Will the repair show?
On a glossy bath, you will struggle to find it. On older, dull enamel the repair can look glossier than the area around it.
What bath repair costs
Repairs from £95. Each job gets its own fixed quote. This is what makes a difference:
- The material
- Doing more than one item at once
- The colour and finish to match
- How many areas need work
Rather than charging by the hour, we price the entire job up front. It depends on the damage, the material and access, and combining items on one visit brings it down.
Send pictures for a quote
Two or three clear photos are normally enough. It helps if you send:
- One picture of the entire bath
- The postcode, so we can plan the visit
- Something in shot to show the size
- Any earlier repairs or coatings
The quickest way to a price is to send two or three photos through our quote form or call us. We’ll tell you honestly if a repair is the right fix.
Where we work around Moorend
Moorend is about 9 miles west of Belper, in Derbyshire. Our work suits any type of property, from flats and terraces to detached houses and new builds, plus businesses and rented homes. Our technicians cover 532 places in Derbyshire. We work right across the region, from Moorend to Birmingham (about 38 miles away).
We cover every part of the DE6 postcode area and the streets around it. Neighbouring places we cover include Bradley (1 mile north-east), Hulland (2 miles north-east), Atlow (2 miles north-east), Hulland Ward (3 miles east) and Upper Biggin (3 miles north-east). Within a short drive, we also cover Ilkeston (15 miles east), Belper (9 miles east), Heanor (14 miles east), Ripley (12 miles east), Langley Mill (14 miles east) and Matlock (11 miles north-east).
Landmarks near Moorend
Our customers here include homes close to Queen Elizabeth's Grammar School, Church of All Saints and Bradley CofE Primary School and the streets around them. A little further out are Hamilton House Toy Museum (2.5 miles west) and St Oswalds Hospital (2.7 miles west).
- Parks and local facilities nearby include Ashbourne Rural District (2.4 miles west)
Nearby places to Moorend
More services for Moorend
For landlords and businesses
We also carry out snagging repairs for builders and developers, putting right damage done during fitting so nothing needs replacing. We’re CHAS, Constructionline and SafeContractor accredited.
Rented homes see more wear and tear, and replacing things at every changeover adds up. Repairing between tenants keeps the property presentable for less.
About our accreditations · Every repair comes with a one-year guarantee.
