Derbyshire · England
Bath chip & crack repair in Shirland, Derbyshire
Bath repair for Shirland, without a refit. Get a fixed price from your photos, then book a visit.
- Repairs from £95
- Hairline or through cracks in acrylic
- Chips on the rim or sides
What affects the price in Shirland
Prices start from £95. We give every job a fixed price from pictures. These are the things that affect it:
- Unusual colours or finishes
- The type of damage
- Whether old repairs or coatings need taking off
- The material
Instead of hourly rates, we fix the price before we start. Damage, material and access decide it.
Quotes from your pictures
You can take the pictures on your phone, there is no need for anything special. Just make sure we can see:
- One picture of the whole bath
- Whether it’s been repaired or coated before
- The postcode, so we can plan the visit
- Good light, ideally daylight, without flash glare
You don’t need a survey visit. Photos are enough for us to price nearly every job: we need a close-up, a wider picture and your postcode, and we will come back to you with a fixed figure.
Bath repair in Shirland without replacing anything
Bath repair is our most common job. A chip by the taps, a crack in the base and a rust spot by the plughole are all repaired in place, normally in one visit. If you are dealing with deep scratches in acrylic and rusty patches near the plughole, we can typically put it right.
Every repair comes with a one-year guarantee.
- Area
- Shirland (DE55)
- Area hub
- Derbyshire
- Guarantee
- A year, on every repair
- Quote
- From £95. Free and fixed, from your photos
- Telephone
- 0345 017 0787
- Page updated
- 23 October 2026
How to look after the repair
Aftercare is simple, and it makes a real difference:
- Rinse it down after each bath
- Keep metal cans and razors off the surface
- Check that an acrylic bath doesn’t move when you stand in it
- Stick to mild cleaners and a soft cloth
Give the repair the full curing time we recommend before running a bath. From then on, mild cleaning is all it needs.
Small chips are quick to repair. Left alone, they stain and can rust, so it’s worth getting them done early.
Common questions in Shirland
Can you repair a hole in a bath?
Usually. Send us a picture of the hole and one from under the bath if you can.
How long does the repair take to cure?
Normally the next day. We confirm the time before we leave.
Is a bath repair durable?
It should, as long as the bath is firm and the area was prepared well. It’s covered by our one-year guarantee.
Do you hold any accreditations?
Yes. Our accreditations include CHAS, Constructionline and SafeContractor. See our accreditations page for the full list.
Can you repair a failed DIY repair?
Yes. We take out the old repair and do it properly. Mention it when you send photos.
Is the work guaranteed?
Every repair comes with our one-year guarantee. Ask us what it covers when you get your quote.
Do you work for landlords and businesses?
Yes. We carry out repairs for householders, landlords, letting agents, builders and businesses in Shirland.
Can you fix rust around the plughole?
Yes. We take out the rust and any loose enamel, fill the area, then colour-match the finish.
What your bath is made of matters
Acrylic
Acrylic feels warm and is light, but it relies on good support. Repairs to cracks are reinforced from the back.
Cast iron
Cast iron baths are thick and very strong, finished with fired enamel. Chips can rust if left, but the body of the bath lasts a very long time, which makes it well worth repairing.
DIY kit or professional repair?
DIY kits are sold for most surfaces, and they can tidy up a tiny mark. The trouble is colour and preparation: they come in a handful of shades, and if the surface isn’t prepared the repair will not last.
A kit can be fine for a tiny mark out of sight. For damage in plain view, cracks, holes or rust, or coloured finishes, a professional repair is worth it.
How it works
You don’t need to empty the room beforehand. We bring everything we need with us, put protection down and start once you’re happy with the plan. It usually takes a few hours, and you are welcome to carry on with your day while we work.
- We clean the area and remove any loose enamel or rust.
- We fill the damage and sand it flush with the surrounding surface.
- We tint the finish on the day to suit your bath’s shade of white or colour.
- We apply the finish coats and polish the repair so it blends in.
- Once it has cured, normally by the following day, the bath is ready to use.
Getting ready for the visit
- Point us to the nearest place to park
- Move bottles, mats and clutter away from the area
- Make sure the room can be ventilated
Ask for a price
For a price in Shirland, the easiest route is pictures: one close up, one from further back, plus your postcode. We reply with a fixed quote and our next available dates.
Related advice
What we can’t put right
Not everything can be repaired, and we will tell you before we start. We cannot fix:
- A whole bath that’s dull or worn, where a full re-enamel is the better fix
- Water coming from the waste or taps rather than the bath
- Flexing caused by a failed cradle or loose feet
Not sure? Send pictures and we will give you a straight answer.
Materials we repair
- Roll-top & freestanding
- Whirlpool & spa baths
- Cast iron enamel
- Acrylic
- Pressed steel enamel
Towns and villages near Shirland
Other services in Shirland
When to call us in Shirland
Nearly all the chips we see start with something being dropped: bottles, shower heads, tiles and tools. On steel and cast iron baths, any chip down to the metal lets water in, and rust follows.
The things customers typically mention when they call include:
- Cracks in an acrylic bath
- Snagging damage from a refit
- A hole punched through by something heavy
- Scratches you can feel with a fingernail
What your quote should include
- How to look after the finish
- The length of the guarantee and what it covers
- Whether the colour is mixed to match
- What happens if they find more damage
Covering Shirland
Shirland is about 5 miles north of Ripley, in Derbyshire. Our work suits any type of property, from flats and terraces to detached houses and new builds, as well as offices, shops and holiday lets. Shirland is one of 532 towns and villages in Derbyshire where we work. Our nearest city page is Manchester, about 42 miles away.
Jobs in DE55 are booked in the same way as anywhere else. That includes homes on The Fox Hollies, Pinewood Drive and Wellington Park and the roads around them. Other places close to Shirland include Higham (1 mile north-west), Mickley (1 mile north), Ogston (1 mile north-west), Wessington (2 miles west) and Brackenfield (2 miles west). Further out, we also cover Chesterfield (8 miles north), Ilkeston (11 miles south), Belper (7 miles south-west), Heanor (8 miles south), Dronfield (13 miles north) and Ripley (5 miles south).
Landmarks near Shirland
Locally, our jobs take us to homes close to Red Lion pub, St Leonard's Church and David Nieper Academy. The closest station to Shirland is Alfreton station, roughly 2.1 miles south-east of the centre. Other landmarks nearby include Clay Cross Hospital (3.2 miles north) and Clay Cross Urban District (2.9 miles north).
For landlords and businesses
We carry out planned and one-off repairs for housing associations and facilities teams. A repair avoids taking out and refitting, which is easier on the people living there.
Letting agents frequently send us pictures straight from the inventory. You can have a price before you arrange access, and we can arrange access with the tenant directly if that helps.
About our accreditations · Every repair comes with a one-year guarantee.
