Norfolk · England
Bath Resealing for Hamrow homes
Our repair technicians come to Hamrow for bath, shower and sink resealing with new mould-resistant silicone. Nothing is taken out, and the work is guaranteed.
- Silicone coming away from the tiles
- Stained silicone
- Leaks at the edges
About Hamrow
Hamrow is about 8 miles north-west of Dereham, in Norfolk. From the centre of Hamrow to the outlying streets, we offer exactly the same service: fixed prices, tidy work and a one-year guarantee. We cover 797 places across Norfolk.
All of NR20 is within our area, from the main roads to the quietest streets. Nearby, we also work in Whissonsett (1 mile south), Horningtoft (1 mile south-east), Stanfield (2 miles south), Brisley (2 miles south-east) and Tittleshall (2 miles south-west). We also work in nearby towns such as Dereham (8 miles south-east), Watton (14 miles south), Swaffham (11 miles south-west), Fakenham (4 miles north), Holt (14 miles north-east) and Wells-next-the-Sea (12 miles north).
Near you in Hamrow
In Hamrow, that means homes near Church of St Mary and the streets around them. Well-known places in the area include Mileham Castle (2.9 miles south) and Fakenham Museum of Gas and Local History (3.3 miles north). For a walk, there’s Beacon Hill and Pensthorpe Nature Reserve.
Bath resealing in Hamrow, done in place
Baths are resealed with water in them, so the joint opens fully, which stops the new seal tearing the first time the bath is used. Whether it’s sealant that’s split or lifting and stained silicone, we can help, on wet rooms, baths and shower trays & enclosures alike.
The work is covered for a year after we finish. If anything isn’t right, ring us and we’ll come back.
- Location
- Hamrow (NR20)
- County
- Norfolk
- Warranty
- A year, on every repair
- Price
- Fixed and free, based on photos
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Repairs by material
Sinks and worktops
Basins, vanity units and kitchen worktops are resealed too, once the joint is completely dry.
Shower trays
Trays are sealed with weight on them, for the same reason.
Also near Hamrow
Other services in Hamrow
What we can’t put right
It helps to know what we can’t do too:
- Tiles that move, until they’re refixed
- A flexing bath
- Very wide gaps that need a trim
Send us photos and we will tell you honestly before booking.
Materials we work on in Hamrow
- Baths
- Wet rooms
- Kitchen worktops & sinks
- Basins & vanity units
- Shower trays & enclosures
Resealing in Hamrow: why it matters
Compared with repairing water damage, resealing is cheap. It’s a quick job that protects your walls and floors. What it costs depends on the type and amount of damage, what it’s made of and how many items we do on one visit. You get a fixed quote from your photos, so you know the cost before you book.
Why choose Surface Doctor in Hamrow
- Fixed prices from your photos
- One-year guarantee on every repair
- Accredited with CHAS, Constructionline and SafeContractor
- No extra charge for your area
Read our full price list.
Should I try a DIY kit first?
If you’ve already tried a DIY fix, that’s fine. We remove the old filler and start again, so it does not stop a professional repair. Just mention it when you send pictures, as it can add time.
For a hairline mark somewhere you’ll never see, a kit may be enough. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, it’s worth having it done properly.
What affects the price in Hamrow
We do not charge extra for travel to Hamrow. The price depends on:
- Access to the area
- What the surface is made of
- Unusual colours or finishes
- Previous DIY repairs that have to come out
Most people are surprised how affordable a repair is, particularly next to the cost of replacement. Send photos and we’ll give you the exact figure.
Quotes from your photos
It only takes a minute to photograph the damage, and it saves a visit. Try to send:
- The material, if you know it
- A coin or ruler next to the damage for scale
- Good light, ideally daylight, without flash glare
- One sharp close-up of the damage
For a price in Hamrow, the easiest route is photos: a close-up, a wider shot and your postcode. We reply with a fixed quote and our next available dates.
Signs you need bath resealing in Hamrow
Most reseals are because of black mould. It grows into the sealant itself, so cleaning cannot get it all out.
You may need us if you’ve spotted any of these:
- Gaps by the taps
- Damp near the bath
- An untidy old seal
- Stained silicone
What to look for in a quote
- What preparation is included
- How your room will be protected
- Whether they match the colour on site
- How changes to the job are handled
Hamrow: your questions answered
Will you leave a mess?
Dust sheets and masking go down before we start, and we clean up when we have finished.
What areas do you cover?
Across the UK, so Hamrow is covered. Prices don’t change with location.
Are you accredited?
Yes, including CHAS, Constructionline and SafeContractor. See our accreditations page for the full list.
Do you seal over the old sealant?
No, we never seal over old silicone. It’s removed, cleaned off and the joint dried first.
Why does mould come back so fast?
Mostly moisture and poor ventilation. We use mould-resistant silicone, and ventilation helps it last.
How do I book?
A close-up, a wider photo and your postcode. After that, we just agree a date.
What happens after I send pictures?
You get a fixed price and available dates. If anything’s unclear, we’ll ask for another photo.
Do you come to Hamrow?
Yes. We work across the UK and travel to Hamrow and the rest of Norfolk. Send pictures and we will quote, or call 0345 017 0787.
Aftercare tips
So the finish stays in good condition for years:
- Clean the joints with a mild cleaner
- Let steam out after showers
- Ventilate the bathroom well
- Store bottles on a shelf
Use the extractor fan, wipe the joints dry after use, and clean them regularly with a mild cleaner to slow mould growth.
Black mould in sealant is not just unsightly. Resealing early keeps water out of the walls and floor.
The process
Here’s how a visit normally runs: we arrive at the agreed slot, protect everything around the work area, do the job and tidy away. Allow about two hours for a bath from start to finish. Before we go, we will explain when it can be used and what to avoid for the first few days.
- We cut out all of the old sealant.
- We remove the residue and clean the joint.
- We treat mould and dry the joint thoroughly.
- We fill the bath, or weight the tray, to open the joint.
- New mould-resistant silicone is applied and tooled neatly.
Before we arrive
- Make sure the area is dry
- Tell us about any previous repairs or coatings
- Tell us if there are stairs or a lift
Get a quote
You don’t need a survey visit. Photos are enough for us to price nearly every job: we need a close-up, a wider picture and your postcode, and we will come back to you with a fixed figure.
Related advice
About our accreditations · Every repair comes with a one-year guarantee.
