Kent · England
Bath Re-enamelling in Barnes Cray
Bath re-enamelling in Barnes Cray without the cost of replacing. Send us photos for a fixed quote, then we come to you.
- Resurfacing from £350
- A peeling or bubbling previous coating
- A bath that stays dull however much you clean it
How we handle bath re-enamelling in Barnes Cray
Many of the baths we re-enamel are period roll-tops, which would be difficult and expensive to replace. Resurfacing them in place keeps the original bath. We’re often asked to fix brown or grey marks that don’t clean off and lots of chips and rust spots, across pressed steel baths, Victorian roll-tops and acrylic baths.
We stand behind the work with a one-year guarantee, so you’re covered after the visit.
- Location
- Barnes Cray (DA1, DA8)
- County
- Kent
- Guarantee
- 12 months on all our work
- Quotes
- From £350. Fixed and free, based on pictures
- Call
- 0345 017 0787
- Updated
- 23 October 2026
Should I try a DIY kit first?
If you’ve already tried a DIY fix, that is fine. We remove the old filler and start again, so it won’t stop us repairing it. It does add a little time, so tell us about it when you send pictures.
We understand the appeal of fixing it yourself. The trouble is that kit repairs often look fine at first and then fail, and then the old filler has to be removed first.
When to call us in Barnes Cray
Once enamel loses its gloss, it stains more easily, and cleaning harder only makes it worse. At that stage, resurfacing is the fix.
The most common problems we are called about are:
- Worn patches where water runs and sits
- A peeling or bubbling previous coating
- Several chips and rust patches
- A coloured bath you want in white
What your quote should include
- How long the guarantee is and what it covers
- How your room will be protected
- What preparation is included
- Whether the price is fixed and includes VAT
When we would advise against a repair
Not everything can be repaired, and we’ll tell you before we start. We can’t fix:
- Problems we can’t see until an old finish comes off
- Holes rusted through the metal
- A metal bath with a through crack
If in doubt, send pictures and we will say what we think before you book.
Surfaces we repair
- Victorian roll-tops
- Cast iron baths
- Pressed steel baths
- Basins & shower trays
- Acrylic baths
Landlords, agents and businesses in Barnes Cray
Letting agents often send us photos straight from the inventory. That means we can quote before you even visit the property, and we can arrange access with the tenant directly if that helps.
We regularly work with letting and managing agents. Just send photos, the address and how to get access and we will handle the rest.
Where we work around Barnes Cray
Barnes Cray is about 2 miles north-west of Dartford, in Kent. Clients in Barnes Cray get the same service as everywhere else we cover: a fixed quote from your pictures, and a technician at your door on the day. We cover 922 places across Kent. Our nearest city page is London, about 13 miles away.
Every address in DA1 and DA8 is within our area. That includes homes on Stour Road, Wilmot Road and Maiden Lane. We also cover the places around Barnes Cray: Slade Green (1 mile north), North End (1 mile north), Crayford (1 mile south-west), Barnehurst (1 mile west) and Bexley Riverside (1 mile north-west). We also work in nearby towns such as Sevenoaks (12 miles south), Gravesend (8 miles east), Northfleet (7 miles east), Swanley (4 miles south), Swanscombe (4 miles east) and Windmill Hill (8 miles east).
Local landmarks in Barnes Cray
Locally, our jobs take us to homes close to Christ Church, Braeburn Park and Bird in Hand pub, among other places. Also close by are Haberdashers' Aske's Crayford Academy (under half a mile west) and Holy Trinity Church of England Primary School (0.6 miles south-east). The nearest railway station is Slade Green station, roughly 0.7 miles north. Other landmarks nearby include Broadway Shopping Centre (2.2 miles west) and West Hill Hospital (1 mile south-east). Not far away are Wansunt Pit.
- Parks and local facilities nearby include Colyers (1.3 miles north-west)
Looking after it afterwards
Once the work has cured, treat it gently:
- Wash away dyes and oils after use
- Do not leave bottles, razors or sponges standing on the surface
- Have chips seen to early
- Avoid suction-cup mats
Rinse the bath and wipe it over after use, especially in hard water areas, so limescale can’t build up.
If a previous coating is starting to peel, don’t pick at it. Moisture gets underneath and makes it worse, so have it stripped and resurfaced.
Materials and what they mean for the repair
Acrylic
Acrylic is light and warm to the touch, but it needs firm support underneath. Cracks are strengthened from behind before the front is finished.
Pressed steel
Under the enamel of a steel bath is thin metal. Once a chip exposes it, rust follows quickly, so the metal is treated and sealed before the repair.
What we do, step by step
Visits start with a quick look at the job together. Next, we cover and mask everything nearby and we start. It normally takes most of the day, and we’ll tell you if anything changes.
- We check the bath and agree the finish with you.
- Taps, tiles and the floor are masked off.
- We degrease the bath, fix any damage and key the surface.
- Primer and finish coats are applied.
- The masking comes off, we tidy up and tell you when it can be used.
Preparing for the visit
- Avoid using the area for a few hours before we arrive
- Mention any earlier repairs or resurfacing
- Open a window if you can
How to get a price
The quickest way to a price is to send two or three pictures using our quote form or ring us. We will tell you honestly whether it can be repaired.
Read more
Common questions in Barnes Cray
Do I have to be there?
Yes. We need access to the room while we work, at a time we agree with you.
Is it worth repairing rather than replacing?
Typically, when the rest is in good condition. A repair avoids removal and making good. We’ll tell you honestly if replacement makes more sense.
What if the damage is worse than the pictures show?
If we find something the photos didn’t show, we explain it first. The price only changes if you agree.
How long does re-enamelling take?
Normally one day, with the bath ready the day after. A badly pitted bath can need a second day.
Do you do work for letting agents?
Yes. We carry out repairs for homeowners, landlords, letting agents, builders and businesses.
How soon can you come?
We will give you dates with your quote. If it’s urgent, say so and we will do what we can.
Are there extra charges for Barnes Cray?
No. Our quotes include travel, with the same prices everywhere we work.
Are you a vetted contractor?
Yes. Our accreditations include CHAS, Constructionline and SafeContractor. See our accreditations page for the full list.
Towns and villages near Barnes Cray
What else we do in Barnes Cray
What bath re-enamelling costs
Resurfacing from £350. You’ll know the full cost before you book. We take into account:
- Whether old repairs or coatings need taking off
- Whether we combine several jobs
- Where the damage is and how we get to it
- How many areas need work
What it costs depends on how much damage there is and what kind, the material and how many items we do on one visit. We give a fixed price from your photos, so there are no surprises on the day.
Getting a price from photos
Good pictures mean an accurate price. Here’s what helps:
- A clear, close picture of the problem area
- Where you are, by postcode
- Any details about the material
- Details of any past repairs
Call 0345 017 0787 or use the quote form. With one close-up and one wider picture, we can price the job the same day in most cases.
About our accreditations · Every repair comes with a one-year guarantee.
