Nottinghamshire · England
Bath re-enamelling & resurfacing in Calverton, Nottinghamshire
Fixed-price bath re-enamelling in Calverton and the surrounding area, normally in one visit.
- Resurfacing from £350
- A roll-top that’s seen better days
- Worn patches where water runs and sits
Bath re-enamelling at your home in Calverton
Cast iron, steel, acrylic, roll-top and period baths can all be resurfaced. The finish is sprayed on in several coats over a bonding primer, once the bath has been cleaned, repaired and prepared. Whether it’s a coating lifting around the plughole and wear marks under the taps, we can help.
You’re covered after we leave: each job carries a one-year guarantee, and we’ll explain exactly what it covers when we quote.
- Area
- Calverton (NG14)
- Region
- Nottinghamshire
- Warranty
- One year on every repair
- Quote
- From £350. Free, fixed quote from pictures
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
When a repair isn’t the answer
We will not take on work that will not last, so here’s what a repair cannot put right:
- Damage hidden under a previous coating, until it’s stripped back
- An acrylic bath that flexes badly underfoot
- Leaks from fittings rather than the bath
Send us photos and we’ll tell you honestly before booking.
Materials we repair
- Cast iron baths
- Acrylic baths
- Pressed steel baths
- Victorian roll-tops
- Basins & shower trays
Keeping it looking good
To keep it looking its best for years:
- A dripping tap should be fixed promptly
- Don’t leave a chip unrepaired
- Leave the bath for the full curing time before using it
- Avoid suction-cup mats
The first few days matter most: let it cure fully, then use mild cleaners only. From then on, avoid abrasives and suction mats.
Leave a peeling coating alone. Water gets under it and the damage spreads, so it’s better to have it stripped and redone.
What your bath is made of matters
Acrylic
Acrylic feels warm and is light, but it relies on good support. Repairs to cracks are reinforced from the back.
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. Only the enamel surface wears or chips, and that is the part we put right.
The process
A typical visit goes like this: we arrive at the agreed slot, sheet and mask the area around the job, do the job and clear up. Allow the best part of a day from start to finish. Before we go, we will explain how long to leave it and what to avoid for the first few days.
- We mask and protect the room and ventilate it.
- Next we degrease the bath and fix chips and rust spots.
- We key the surface and put on a bonding primer.
- We spray on the new enamel finish in several coats.
- The bath is left to cure and can typically be used the day after.
Preparing for the visit
- Clear toiletries, mats and anything else from around the area
- Avoid using the area for a few hours before we arrive
- Tell us if there are stairs or a lift
Getting a price
You do not need a survey visit. Photos are enough for us to price nearly every job: send a close-up, a wider shot and your postcode, and we’ll come back to you with a fixed figure.
Related advice
Landlords, agents and businesses in Calverton
Landlords, letting agents and housing providers in Calverton use us as well as homeowners. A repair between tenants keeps the property empty for less time, and it generally costs far less than a refit.
Hospitality businesses cannot afford rooms out of action for long, so most of our work is done in a single visit. We can work around your bookings.
What affects the price in Calverton
Resurfacing from £350. Every quote is fixed and free. What we look at:
- The material
- Doing more than one item at once
- Where the damage is and how we get to it
- Whether it’s a chip, crack, burn or wear
Every job is a little different, so each one is priced on its own. The size and type of damage, the material and access all make a difference, and combining jobs on one visit brings the cost down.
How to get a fixed quote
Good photos mean an accurate price. Here’s what we find most useful:
- Where you are, by postcode
- A coin beside the damage so we can judge size
- Any details about the material
- Daylight if possible, and no flash reflection
For most jobs, pictures are all we need to give you a price. Tell us what happened and where you are, and we will reply with a fixed quote and the earliest dates we have.
Repairing versus replacing in Calverton
Getting a cast iron bath out is hard work: they’re heavy, often need breaking up, and a new one is not cheap. Re-enamelling avoids all of it. Our bath re-enamelling starts from £350. There are no surprise extras on the day. The price we quote from your photos is the price you pay, unless the damage turns out to be different, in which case we talk to you first.
Why us?
- We will tell you if it’s not worth repairing
- Accredited with CHAS, Constructionline and SafeContractor
- Generally one visit, start to finish
- Everything repaired in place
See our pricing and bath cost comparison.
Calverton: your questions answered
Do you resurface freestanding baths?
Yes. We can do the inside and outside if you’d like.
Do I need to be at home?
Someone needs to let us in and show us the job. You don’t need to watch us work.
What information do you need?
Some pictures, your postcode and how to reach you. On the day, access to the room.
How quickly can you book me in?
It depends on the time of year and where you are. Send photos with your postcode and we will reply with the earliest dates.
Will it make a mess?
Dust sheets and masking go down before we start, and tidy up before we leave.
What does bath re-enamelling cost?
Resurfacing from £350. Because every job differs, we price from pictures. You’ll get a fixed figure before booking.
Will the new finish last?
That depends on preparation and how the bath is treated. Properly prepared and looked after, it lasts well, and our work is guaranteed for a year.
What if the damage is worse than the pictures show?
We’ll show you and explain before doing anything extra. Nothing extra is done without your say-so.
Can I fix it myself?
We understand the appeal of fixing it yourself. The risk is that a kit repair hides the damage for a while, then fails, and the old filler has to come out before a proper repair.
A DIY attempt isn’t a disaster. We remove the old filler and start again, so it doesn’t stop a professional repair. It does add a little time, so tell us about it when you send pictures.
Towns and villages near Calverton
What else we do in Calverton
Covering Calverton
Calverton is about 3 miles north-east of Arnold, in Nottinghamshire. From the centre of Calverton to the outlying streets, we offer exactly the same service: a fixed quote, a tidy visit and a guarantee. We work in 329 places across Nottinghamshire, from the larger towns to small villages. Our nearest city page is Birmingham, about 52 miles away.
We work across NG14 and the streets around it. Whether you live on Main Street, Sherbrooke Close and Bucklee Drive or anywhere nearby, a technician can come to you. Close by, we cover Oxton (2 miles north-east), Woodborough (2 miles south-east), Epperstone (2 miles east), Oxton Hill (3 miles north-east) and Lambley (3 miles south). Further out, we also cover Mansfield (8 miles north-west), Beeston (10 miles south-west), Carlton (5 miles south), Sutton in Ashfield (9 miles north-west), Hucknall (5 miles west) and Newark-on-Trent (12 miles east).
Local landmarks in Calverton
Locally, our jobs take us to homes close to Manor Park Infant and Nursery School, St Wilfrid's Church and Colonel Frank Seely Academy and the streets around them. The nearest railway station is Burton Joyce station, about 4.3 miles south-east of the centre. Other landmarks nearby include Lowdham Motte (3.6 miles south-east) and Calverton Folk Museum (within half a mile south-east).
About our accreditations · Every repair comes with a one-year guarantee.
