Slough · England
Bath Re-enamelling for Fulmer homes
Local bath re-enamelling for Fulmer: a fixed quote from pictures, a tidy visit and a one-year guarantee.
- Resurfacing from £350
- Worn patches where water runs and sits
- An old resurfacing that is failing
Bath re-enamelling in Fulmer, done in place
We clean, repair and prime the bath before spraying the new finish. Most of the work, and most of the durability, is in the preparation, and we take our time over it. Our technicians work on cast iron baths, pressed steel baths and Victorian roll-tops, and people most frequently call us about a roll-top that’s seen better days and a peeling or bubbling previous coating.
A one-year guarantee comes as standard, so you are covered after the visit.
- Location
- Fulmer (SL3)
- Area hub
- Slough
- Warranty
- One year on every repair
- Price
- From £350. Free, fixed quote from pictures
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
What affects the price in Fulmer
Prices start from £350. We charge the same across the UK, including Fulmer. The price reflects:
- Whether it’s a chip, crack, burn or wear
- Previous DIY repairs that have to come out
- The size and number of damaged areas
- How hard the colour is to match
Every job is a little different, so each one is priced on its own. The size and type of damage, the material and access all make a difference, and doing several things on one visit costs less than separate visits.
Send pictures for a quote
Photographing the damage takes a minute, and it saves a visit. Try to send:
- A coin or ruler next to the damage for scale
- The material, if you know it
- A clear, close picture of the problem area
- Any earlier repairs or coatings
There’s no need for us to visit first. Photos are enough for us to price nearly every job: we need a close-up, a wider picture and your postcode, and we’ll reply with a fixed quote.
Materials and what they mean for the repair
Cast iron
Cast iron baths are the classic candidate for re-enamelling. They’re built to last, and only the surface wears, so a new finish makes them look new again.
Roll-top and period baths
Freestanding roll-tops can be done inside and out, with the outside refinished as well.
Fulmer questions
Is there a call-out fee?
There is no separate call-out charge. Your fixed price includes everything.
Can you quote from pictures?
Nearly always. If pictures do not show enough, we will ask for another angle.
Will the new finish last?
A well-prepared finish lasts a long time if it’s looked after. Avoid abrasive cleaners and suction mats.
How do I book?
Just photos, your postcode and a contact number. On the day, access to the room.
Will you leave a mess?
We protect the room with dust sheets and masking first, and we clean up when we have finished.
Can pets and children be at home?
Keep pets and children away from the work area on the day, mainly so nothing gets touched before it has cured.
Which areas do you work in?
All of Slough, and the rest of the UK. There is no extra charge for travel.
Is there a smell?
A little, during the work. We set up ventilation and the smell fades as it cures.
For landlords and businesses
Rented homes see more wear and tear, and replacing items every time a tenant leaves is expensive. A repair between tenancies is a cheaper way to keep the property in good order.
Builders, developers and site managers book us for snagging repairs, fixing chips and scratches before handover so nothing needs replacing. We are CHAS, Constructionline and SafeContractor accredited.
Repairing versus replacing in Fulmer
A new bath means a plumber, removing a heavy bath, re-tiling or making good the walls and several days without a working bathroom. Re-enamelling renews the entire surface without moving it. Our bath re-enamelling starts from £350. The price depends on the type and amount of damage, what it’s made of and how many items we do on one visit. You get a fixed price from your pictures, so you know the cost before booking.
Why choose Surface Doctor in Fulmer
- No extra charge for your area
- We leave the room as we found it
- Accredited with CHAS, Constructionline and SafeContractor
- Nothing taken out or refitted
Read our pricing or resurfacing vs replacement cost guide.
What we can’t put right
We would rather lose a job than do one that won’t last, so here’s what a repair can’t put right:
- Acrylic that moves when you stand in it
- Anything hidden under an old coating, until we remove it
- Leaking taps or wastes (a plumber’s job)
If in doubt, send photos and we will say what we think before booking.
What we work on
- Cast iron baths
- Acrylic baths
- Basins & shower trays
- Pressed steel baths
- Victorian roll-tops
What else we do in Fulmer
What happens on the day
Visits start with a quick look at the job together. Next, we cover and mask everything nearby and we start. You can expect it to take the best part of a day, and we’ll tell you if anything changes.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures.
Getting ready for the visit
- Make sure the room can be ventilated
- Move bottles, mats and clutter away from the area
- Let us know if it has been repaired before
Ask for a price
Call 0345 017 0787 or use the quote form. With a clear picture of the damage and one of the whole bath, we can price the job.
Read more
DIY kit or professional repair?
You can buy a DIY kit for most repairs, and they can make a small mark look better. The trouble is colour and preparation: they come in a handful of shades, and if the surface is not prepared the repair will not last.
If you’ve already tried a DIY fix, that’s fine. We take the old repair out and do it properly, so it does not stop a professional repair. It does add a little time, so tell us about it when you send pictures.
Looking after it afterwards
Once the work has cured, treat it gently:
- Don’t use the bath until it has fully cured
- Get any chip repaired quickly
- Never use suction bath mats
- Use washing-up liquid and a soft cloth
Treat the new finish gently at first: let it cure fully, then use mild cleaners only. From then on, avoid abrasives and suction mats.
Rust spots on a worn bath get worse with time, and each one adds to the preparation. Resurfacing before they spread keeps it simpler.
Covering Fulmer
Fulmer is about 4 miles north-east of Slough, in Slough. We agree a date that works for you, and you will know when to expect us, so there’s no waiting around. Fulmer is one of 31 places in Slough where we work. You can also see our page for London, about 20 miles away.
We cover every part of the SL3 postcode area. Local streets include Fulmer Road, Alderbourne Lane and Hay Lane, and we cover them all. We also cover the places around Fulmer: Tatling End (1 mile north-east), Wexham Street (1 mile south-west), Gerrards Cross (1 mile north), Stoke Poges (2 miles south-west) and Rush Green (2 miles east). Larger places within reach include Slough (4 miles south-west), Cippenham (5 miles south-west), Chalvey (4 miles south-west), Britwell (3 miles south-west), Langley (4 miles south) and Upton (4 miles south).
Local landmarks in Fulmer
Typical jobs here are in homes near Church of St James, Bulstrode Park and Khalsa Secondary Academy and the streets around them. You’ll also find The Black Horse Public House (under half a mile south-west) and Fulmer Infant School (within half a mile south). The nearest railway station is Gerrards Cross station, about 1.9 miles north. Other landmarks nearby include British Airways Heritage Collection (3.5 miles south-east) and Wexham Park Hospital (2.2 miles south). For a walk, there is Horse Shoe Bay and Stoke Common.
About our accreditations · Every repair comes with a one-year guarantee.
