Shropshire · England
Bath Re-enamelling for Lyneal homes
Bath re-enamelling in and around Lyneal: photo quotes, tidy work and a year’s guarantee.
- Resurfacing from £350
- Chips and rust in more than one place
- Stains that won’t shift
Bath re-enamelling at your home in Lyneal
We clean, repair and prime the bath before spraying the new finish. The preparation is what makes it last, so we don’t cut corners on it. Whether it’s several chips and rust patches and an old resurfacing that’s failing, we can help, on acrylic baths, basins & shower trays and Victorian roll-tops alike.
The work is guaranteed for twelve months. If something isn’t right in that time, we come back and put it right.
- Location
- Lyneal (SY12)
- Area hub
- Shropshire
- Guarantee
- One year on every repair
- Price
- From £350. Free, fixed price from pictures
- Telephone
- 0345 017 0787
- Updated
- 23 October 2026
Where we work around Lyneal
Lyneal is about 10 miles east of Oswestry, in Shropshire. Customers in Lyneal get the same service as everywhere else we cover: a fixed price from your photos, and a technician at your door on the day. Lyneal is one of 433 towns and villages in Shropshire we cover. Our jobs stretch from Lyneal to Liverpool (36 miles away).
Here we cover the SY12 postcode area. Neighbouring places we cover include Balmer Heath (1 mile north-west), Breaden Heath (1 mile north), Welshampton (1 mile north-west), Rowe (1 mile north) and Northwood (1 mile east). We also work in nearby towns such as Shrewsbury (13 miles south), Oswestry (10 miles west), Market Drayton (14 miles east), Coleham (14 miles south), Kingsland (13 miles south) and Whitchurch (8 miles north-east).
Local landmarks in Lyneal
Typical jobs here are in homes near Church of St John the Evangelist, among other places. Nearby you will also find Ellesmere Castle (2.7 miles west) and Penley Community Hospital (4.5 miles north-west). Not far away are Newton Mere.
Do you need bath re-enamelling in Lyneal?
Previous coatings can fail too, lifting by the plughole or blistering. Failing coatings are stripped back before we resurface.
If you can see any of these, send us a picture:
- Lots of chips and rust spots
- A coating lifting around the plughole
- Enamel that’s lost its shine and feels rough
- An original cast iron bath that needs restoring
Comparing quotes
- What protection goes down before work starts
- What happens if they find more damage
- What the guarantee covers, and for how long
- Whether there are any call-out or travel charges
Repair or replace: which is better?
Replacing a bath can take several days across several trades. Resurfacing takes one technician and generally a day. Prices start from £350. A repair generally costs much less than people expect, particularly next to the cost of replacement. Photos let us give you the exact figure.
Why choose Surface Doctor in Lyneal
- Accredited with CHAS, Constructionline and SafeContractor
- A year’s guarantee on all work
- No need to remove anything
- One price list for the whole UK
See our prices page or resurfacing vs replacement cost guide.
What bath re-enamelling costs
Resurfacing from £350. We charge the same across the UK, including Lyneal. What changes the price is:
- The material
- How many areas need work
- How hard the colour is to match
- What kind of damage it is
No two jobs are quite the same, so we price each one individually. The size and type of damage, the material and access all play a part, and combining jobs on one visit brings the cost down.
Send pictures for a quote
Photographing the damage takes a minute. Please include:
- A coin or ruler next to the damage for scale
- Any earlier repairs or coatings
- A clear, close picture of the problem area
- Your postcode, so we can check dates
You don’t need a survey visit. Photos are enough for us to price nearly every job: send a close-up, a wider shot and your postcode, and we will reply with a fixed price.
Towns and villages near Lyneal
Also in Lyneal
Work for landlords and builders
We work for landlords, letting agents and housing providers in Lyneal as well as homeowners. A repair between tenants keeps the property empty for less time, and it costs much less than replacing.
We regularly work with letting and managing agents. Just send pictures, the address and how to get access.
How to look after the repair
After the repair has cured, a few habits help it last:
- Don’t use the bath until it has fully cured
- Never use suction bath mats
- Don’t leave a chip unrepaired
- A dripping tap should be fixed promptly
Stick to mild, non-abrasive cleaners, do not use suction bath mats, and keep bottles and razors off the surface.
Avoid scrubbing a dull bath with abrasive cleaners. It just wears the enamel further.
What happens on the day
When we visit, we arrive at the time we have agreed, cover the area with dust sheets and masking, and set to work. The job usually takes most of the day. We clean up when we are done and tell you when it’s ready to use.
- We mask and protect the room and ventilate it.
- We clean and degrease the bath and repair any chips or rust.
- We prepare the surface and apply a bonding primer.
- We spray on the new enamel finish in several coats.
- Once cured, normally by the next day, the bath is ready.
Preparing for the visit
- Let us know which floor the room is on
- Make sure the area is dry
- Open a window if you can
Getting a price
For a price in Lyneal, pictures are the quickest way: a close-up, a wider shot and your postcode. We reply with a fixed quote and our next available dates.
Related advice
Your questions about bath re-enamelling in Lyneal
What happens next?
You’ll get a fixed quote back, normally with dates to choose from. You’re under no obligation.
Do you work in Lyneal?
We do. We send a technician to Lyneal for every job, and the price is the same as everywhere else.
Do I have to be there?
We need someone to let us in. After that, you can carry on with your day.
How quickly can you book me in?
We will give you dates with your quote. Tell us if you need it done quickly.
Can you re-enamel a roll-top bath?
Yes, frequently. The inside is resurfaced, and we can refinish the outside as well.
Can you repair several things at once?
Of course, and it normally saves money. Just add the extra items to your pictures and we’ll quote them together.
Can you change the colour of my bath?
Yes, white is the usual choice. Tell us what you’d like when you ask for a quote.
What does bath re-enamelling cost?
Resurfacing from £350. The exact price depends on the damage, so we quote from photos. You know the full cost before anything is booked.
What we cannot put right
In fairness, some problems need a different fix:
- A cast iron or steel bath that’s cracked right through
- Acrylic that moves when you stand in it
- A bath that’s rusted through
Send us pictures and we will tell you honestly.
Materials we work on in Lyneal
- Cast iron baths
- Basins & shower trays
- Pressed steel baths
- Victorian roll-tops
- Acrylic baths
What your bath is made of matters
Cast iron
Cast iron baths are so heavy that repairing in place makes obvious sense. The enamel is the part that wears or chips, and that’s what we repair.
Roll-top and period baths
Freestanding roll-tops can be done inside and out, with the outside refinished as well.
About our accreditations · Every repair comes with a one-year guarantee.
