Staffordshire · England
Bath Re-enamelling for Oakamoor homes
Our technicians come to Oakamoor for full bath re-enamelling and resurfacing. Everything is done in place, and the work is guaranteed.
- Resurfacing from £350
- Staining under the taps and around the waste
- Enamel that is lost its shine and feels rough
Work for landlords and builders
Builders use us to fix snagging damage before handover, so there’s no need to replace a damaged item at the last minute. We can visit several plots in one trip.
Letting agents frequently send us pictures straight from the inventory. That means we can quote before you even visit the property, and we liaise with tenants about access if you’d like us to.
Bath re-enamelling in Oakamoor without replacing anything
We clean, repair and prime the bath before spraying the new finish. The preparation is what makes it last, so we don’t cut corners on it. Typical jobs include a bath that stays dull however much you clean it and lots of chips and rust spots, across cast iron baths, Victorian roll-tops and acrylic baths.
The work is covered for a year after we finish. If anything isn’t right, ring us and we will come back.
- Where
- Oakamoor (ST10)
- County
- Staffordshire
- Cover
- A year, on every repair
- Quote
- From £350. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Aftercare tips
A little care keeps the finish looking good. Our advice:
- Wash away dyes and oils after use
- Never use suction bath mats
- Dry the bath after use to stop limescale
- Stick to gentle, non-abrasive cleaners
Rinse away dyes, oils and bath bombs straight after use, because they can mark the finish. Fix dripping taps quickly.
The longer worn enamel is left, the rougher it gets, and rust spots spread under the surface. Resurfacing sooner means less repair work first.
What your bath is made of matters
Pressed steel
Pressed steel baths take a new finish well, once any rust has been treated. Steel often rusts by the plughole, so we pay close attention there.
Roll-top and period baths
We can resurface a roll-top inside and out, and the outside can be refinished too.
What a repair cannot fix
We will always be straight with you, so here’s what a repair will not do:
- Problems we can’t see until an old finish comes off
- Plumbing leaks, which need a plumber
- Steel that has corroded right through
If in doubt, send photos and we’ll say what we think before you book.
Materials we work on in Oakamoor
- Pressed steel baths
- Victorian roll-tops
- Cast iron baths
- Acrylic baths
- Basins & shower trays
Nearby places to Oakamoor
More services for Oakamoor
Should you replace it?
Replacing a bath can take several days across several trades. Resurfacing takes one technician and usually a day, with the bath back in use the following day. Our bath re-enamelling starts from £350. We charge the same wherever you are, with no extra for Oakamoor. The job itself decides the price: how much damage, what it’s made of and how many items.
What you get with us
- Accredited with CHAS, Constructionline and SafeContractor
- Free fixed quotes from pictures
- No extra charge for your area
- Colours mixed by hand to suit your surface
Read our full price list or resurfacing vs replacement cost guide.
How it works
Expect a friendly, tidy visit. We agree the arrival time in advance, protect the area, and get on with the job, which normally takes the best part of a day. If we find something your photos didn’t show, we’ll explain it before carrying on.
- We check the bath and agree the finish with you.
- Everything around the bath is masked and covered.
- We degrease the bath, fix any damage and key the surface.
- Primer and finish coats are applied.
- We remove the masking, tidy up and give you the curing time.
Getting ready for the visit
- Make sure the area is dry
- Clear the area around the damage
- Mention any earlier repairs or resurfacing
How to get a price
Call 0345 017 0787 or use the quote form. With one close-up and one wider picture, we can give you a fixed price.
Related advice
Oakamoor and the surrounding area
Oakamoor is about 3 miles east of Cheadle, in Staffordshire. Whether you are in the middle of Oakamoor or on the outskirts, we offer exactly the same service: a fixed price, a tidy visit and a guarantee. Our technicians cover 512 places in Staffordshire, from the larger towns to small villages. Our jobs stretch from Oakamoor to Manchester (about 35 miles away).
All of ST10 is covered, from the main roads to the quietest streets. From Church Bank, Churnet View Road and Mill Road or anywhere nearby, we can come to you. Oakamoor is on the B5417, which makes it straightforward to reach. Other places close to Oakamoor include Cotton (1 mile north-east), Whiston (2 miles north-west), Upper Cotton (2 miles north), Broomyshaw (2 miles north) and Kingsley Holt (2 miles north-west). We also work in nearby towns such as Newcastle-under-Lyme (13 miles west), Longton (9 miles west), Stone (12 miles south-west), Leek (8 miles north-west), Biddulph (13 miles north-west) and Kidsgrove (14 miles north-west).
Local landmarks in Oakamoor
Locally, our jobs take us to homes close to The Valley Primary School and Church of the Holy Trinity, among other places. Nearby you’ll also find Cheadle Hospital (3 miles west) and Alton Castle (1.9 miles south-east). Green spaces nearby include Cotton Dell.
DIY repairs versus a professional job
If you are set on a kit, follow its instructions closely, and don’t use it until it has fully cured. If it fails, we can still put it right.
If you’ve already tried a DIY fix, that’s fine. We take the old repair out and do it properly, so it doesn’t stop a professional repair. Just mention it when you send photos, as it can add time.
Your questions about bath re-enamelling in Oakamoor
Which areas do you work in?
Across the UK, and that includes Oakamoor. Prices do not change with location.
Can landlords book you?
Yes, often. We can quote for several properties together and work between tenancies.
How quickly can you book me in?
That depends on our diary for your area. We’ll offer you dates when we send your quote.
I rent my home. Can I book you?
Yes. Check with your landlord; we can send the quote to them too.
Can a failed resurfacing be redone?
Yes. Stripping the old coating adds time, so it’s reflected in the quote.
Do you come to Oakamoor?
We do. Repair technicians travel to Oakamoor from across the region, and the price is the same as everywhere else.
Will you leave a mess?
Dust sheets and masking go down before we start, and tidy up before we leave.
Can you re-enamel a roll-top bath?
Yes, roll-tops are a big part of our work. We resurface the inside, and the outside can be refinished too.
Signs you need bath re-enamelling in Oakamoor
Hard water speeds up the wear, and gritty cleaners are the worst culprits.
Signs it’s time to call us include:
- A coating lifting around the plughole
- Enamel that is lost its shine and feels rough
- Brown or grey marks that don’t clean off
- A period or roll-top bath worth keeping
What to look for in a quote
- How changes to the job are handled
- Whether the colour is mixed to match
- What preparation is included
- How to care for the finish
About our accreditations · Every repair comes with a one-year guarantee.
