Staffordshire · England
Bath re-enamelling & resurfacing in Oaken, Staffordshire
Bath re-enamelling across Oaken and nearby, typically in one visit and guaranteed for a year.
- Resurfacing from £350
- Lots of chips and rust spots
- A period or roll-top bath worth keeping
FAQs for Oaken
Will it make a mess?
No. The work area is masked and covered, and we take our waste away with us.
Do I have to be there?
Someone needs to let us in and show us the job. You don’t need to watch us work.
Can you do more than one item on the same visit?
Of course, and it generally saves money. Just add the extra items to your photos and we’ll quote them together.
Does re-enamelling smell?
Some odour is normal while we spray, which is why we ventilate the bathroom. It clears as the finish cures.
How do I book?
Some pictures, your postcode and how to reach you. On the day, we only need access to the room.
Can I get a quote without a visit?
In nearly every case. We only ask to see it in person if the pictures can’t show what we need.
Is it safe with children and pets around?
We ask you to keep children and pets out of the room while we work and until it has cured. The rest of the house is unaffected.
How long is the bath unusable?
Most baths are done in a day, ready the following day. We will confirm timings when we quote.
Bath re-enamelling at your home in Oaken
After re-enamelling, the bath has a smooth, glossy, new-looking surface, but without the cost and upheaval of a refit. It’s ideal if you like your bathroom but not the state of the bath. We’re often asked to fix a bath that stays dull however much you clean it and a period or roll-top bath worth keeping, in basins & shower trays, cast iron baths and pressed steel baths.
You’re covered for a year from the day of the repair. Just call us if there is a problem and we will sort it.
- Area
- Oaken (WV8)
- Region
- Staffordshire
- Guarantee
- 12 months on all our work
- Price
- From £350. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
How the visit works
Expect a friendly, tidy visit. We confirm the time with you beforehand, cover and mask the work area, and get on with the job, which usually takes a full day. If we find something your pictures didn’t show, we will explain it before carrying on.
- The room is masked, protected and ventilated.
- The bath is cleaned, degreased and any chips or rust repaired.
- The surface is prepared and a bonding primer applied.
- We spray on the new enamel finish in several coats.
- The bath is left to cure and can normally be used the next day.
Preparing for the visit
- Avoid using the area for a few hours before we arrive
- Have a window or extractor fan available
- Clear toiletries, mats and anything else from around the area
Getting a price
Upload a picture of the damage and a wider shot of the entire item, with your WV8 postcode, and we will come back with a fixed quote.
Related advice
Repairs by material
Acrylic
Acrylic baths can be resurfaced too, with a coating system suited to acrylic. It must be solid and not flex underfoot for the finish to last.
Cast iron
A cast iron bath is heavy enough that most people never want to move it. The enamel is the part that wears or chips, and that’s what we repair.
DIY repairs versus a professional job
If you’ve already tried a DIY fix, that is fine. We remove the old filler and start again, so it does not stop a professional repair. Just mention it when you send photos, as it can add time.
It’s tempting to reach for a kit, but many of the jobs we do start with putting right a DIY repair. Doing it properly first is typically the cheaper route.
Other services in Oaken
How to care for the repair
Good habits make a big difference to how long a repair lasts. Here’s what we suggest:
- Avoid suction-cup mats
- Don’t leave bottles, razors or sponges standing on the surface
- A quick wipe after use keeps limescale away
- Stick to gentle, non-abrasive cleaners
A quick rinse and wipe after use helps, especially in hard water areas, to stop limescale building up.
Do not try to scrub a worn bath back to shine. It removes more of the surface.
Do you need bath re-enamelling in Oaken?
Enamel wears gradually. Years of cleaning, hard water and hot baths wear the gloss away, starting where water runs and sits.
You may need us if you’ve spotted:
- Worn patches where water runs and sits
- An original cast iron bath that needs restoring
- A bath that stays dull however much you clean it
- Brown or grey marks that don’t clean off
What to look for in a quote
- What aftercare is recommended
- How soon you can use it again
- What happens if the damage is worse than the photos show
- Whether the price covers travel
Repairing versus replacing in Oaken
Replacement only makes sense in a few cases: if the bath is cracked through, if you want a different size or shape, or if you’re refitting the entire room anyway. In most other cases, resurfacing is the better choice. Resurfacing from £350, with every job priced individually. Every job is a little different, so each one is priced on its own. The size and type of damage, the material and access all play a part, and combining jobs on one visit brings the cost down.
Why us?
- A fixed quote before you book
- Work done at your home or business
- Normally one visit, start to finish
- Straight answers about what a repair can do
See our prices page or guide to resurfacing and replacement costs.
What we cannot put right
Honesty matters more than a booking, so here’s what a repair can’t fix:
- A bath that’s rusted through
- Plumbing leaks, which need a plumber
- An acrylic bath that flexes badly underfoot
Not sure? Send pictures and we will give you a straight answer.
What we work on
- Pressed steel baths
- Acrylic baths
- Cast iron baths
- Victorian roll-tops
- Basins & shower trays
Work for landlords and builders
Builders use us to fix snagging damage before handover. Several plots can be done in one visit.
Letting agents frequently send us pictures straight from the inventory. That means we can quote before you even visit the property, and we liaise with tenants about access if you’d like us to.
Our work in Oaken
Oaken is about 4 miles north-west of Wolverhampton, in Staffordshire. We visit clients in Oaken and nearby villages, so there is no workshop to go to. Oaken is one of 512 places in Staffordshire where we work. Our nearest city page is Birmingham, about 17 miles away.
We work across the WV8 postcode area. Whether you live on Platinum Grange, Shop Lane and Oaken Lane or a nearby road, a technician can come to you. We also cover the places around Oaken: Kingswood (1 mile west), Codsall Wood (2 miles north), Boningale (2 miles west), Albrighton (3 miles west) and Donington (3 miles north-west). Larger places within reach include Stafford (13 miles north), Cannock (10 miles north-east), Rugeley (15 miles north-east), Burntwood (13 miles east), Hednesford (11 miles north-east) and Wombourne (6 miles south).
What’s near Oaken
We visit homes around St Nicholas' Church, St Nicholas Church of England First School and Codsall Community High School, among other places. The closest station to Oaken is Codsall station, about 0.6 miles north-east. Other landmarks nearby include Tong Castle (4.8 miles north-west) and RAF Hospital Cosford (3.8 miles north-west).
About our accreditations · Every repair comes with a one-year guarantee.
