Worcestershire · England
Bath re-enamelling & resurfacing in Stockton on Teme, Worcestershire
We travel to Stockton on Teme for full bath re-enamelling and resurfacing. Everything is done in place, and the work is guaranteed.
- Resurfacing from £350
- An outdated colour you’d like to change
- Lots of chips and rust spots
What we do, step by step
We work cleanly and quietly, so you can stay at home while we are there. Protection goes down first, then the job itself takes the best part of a day. Before we leave, we explain how soon it can be used and how to care for it.
- The bathroom is protected and ventilation set up.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures until the next day.
How to prepare
- Let us know if it has been repaired before
- Avoid using the area for a few hours before we arrive
- Mention if the room is upstairs or in a flat
Ask for a price
If you are in Stockton on Teme and want a price, photos are the quickest way: a close-up, a wider shot and your postcode. We reply with a fixed quote and our next available dates.
Read more
About our bath re-enamelling in Stockton on Teme
We clean, repair and prime the bath before spraying the new finish. The preparation is what makes it last, so we do not cut corners on it. We work on Victorian roll-tops, pressed steel baths and cast iron baths, and people most frequently call us about stains that won’t shift and a dull, rough surface that won’t come clean.
You are covered after we leave: our one-year guarantee applies to every job, and we’ll explain exactly what it covers when we quote.
- Where
- Stockton on Teme (WR6)
- Area hub
- Worcestershire
- Guarantee
- 12 months on all our work
- Price
- From £350. Free, fixed price from pictures
- Phone
- 0345 017 0787
- Page updated
- 23 October 2026
Nearby places to Stockton on Teme
Also in Stockton on Teme
Aftercare tips
Good habits make a big difference to how long a repair lasts:
- Do not use the bath until it has fully cured
- Store bottles off the bath
- Get any chip repaired quickly
- Rinse off hair dye, oils and bath bombs right away
Rinse the bath and wipe it over after use, particularly where water is hard, to stop limescale building up.
If a previous coating is starting to peel, don’t pick at it. Moisture gets underneath and makes it worse, so it’s better to have it stripped and redone.
When we’d advise against a repair
We would rather lose a job than do one that won’t last, so here’s what a repair cannot put right:
- Leaks from fittings rather than the bath
- Holes rusted through the metal
- A bath split right through the body
Send us photos and we will tell you honestly.
What we work on
- Pressed steel baths
- Cast iron baths
- Basins & shower trays
- Victorian roll-tops
- Acrylic baths
Stockton on Teme questions
Do you do work for letting agents?
Yes. We work for landlords, agents, builders and businesses as well as homeowners across Worcestershire.
Can you re-enamel a roll-top bath?
Yes. Inside and out if you’d like.
Can I get a quote without a visit?
In nearly every case. We only ask to see it in person if the pictures cannot show what we need.
Will the price change on the day?
We will show you and explain before doing anything extra. You won’t be charged for anything you haven’t agreed.
Does someone need to be in?
We need someone to let us in. After that, you can carry on with your day.
Does the bath have to be removed?
Not at all. We work on the bath in place, with the room masked and ventilated.
I rent my home. Can I book you?
We’re happy to deal with the tenant, landlord or agent. Just make sure the landlord agrees.
Will it make a mess?
Dust sheets and masking go down before we start, and tidy up before we leave.
When to call us in Stockton on Teme
Once enamel loses its gloss, it stains more easily, and scrubbing it wears it down further. That’s the point where re-enamelling makes sense.
Customers normally contact us about:
- An old resurfacing that is failing
- Brown or grey marks that do not clean off
- A roll-top that is seen better days
- Wear marks under the taps
Questions to ask before booking
- What aftercare is recommended
- How the room is protected while they work
- How soon you can use it again
- Whether a trained technician does the job
Materials and what they mean for the repair
Pressed steel
Under the enamel of a steel bath is thin metal. Once a chip exposes it, rust follows quickly, so we treat and seal the metal before filling.
Acrylic
Acrylic baths can be resurfaced too, with a coating system suited to acrylic. The bath needs to be firm and well supported for the finish to last.
Repairing versus replacing in Stockton on Teme
If the bath is sound, re-enamelling is usually much cheaper than replacing it, once you add removal, plumbing, tiling and decorating to the price of a new bath. It’s much quicker too. Prices start from £350. What it costs depends on how much damage there is and what kind, the material and how many jobs we combine into one visit. We give a fixed price from your photos, so there are no surprises on the day.
Why book with us
- A year’s guarantee on all work
- Nothing taken out or refitted
- Rooms protected and left tidy
- Colours mixed by hand to suit your surface
Read our pricing or guide to resurfacing and replacement costs.
DIY repairs versus a professional job
If you are set on a kit, follow its instructions closely, and give it the full curing time. If it doesn’t work out, we can still repair it properly.
It’s natural to want to try a repair yourself. The risk is that a kit repair hides the damage for a while, then fails, and then the old filler has to be removed first.
Prices and what affects them
Prices start from £350. You will know the full cost before you book. We take into account:
- Unusual colours or finishes
- Doing more than one item at once
- The material
- Whether it’s a chip, crack, burn or wear
A few things move the price: the amount of damage, the material, access to the area, and how many jobs we do in one trip. Photos let us give you a fixed figure.
Quotes from your pictures
You can take the pictures on your phone, there is no need for anything special. Just make sure we can see:
- Your postcode, so we can check dates
- A coin beside the damage so we can judge size
- The material, if you know it
- A clear, close picture of the problem area
Call 0345 017 0787 or use the quote form. With a clear picture of the damage and one of the entire bath, we can give you a fixed quote.
About Stockton on Teme
Stockton on Teme is about 6 miles south-west of Stourport-on-Severn, in Worcestershire. Anywhere in WR6, a technician comes to you. Stockton on Teme is one of 376 places in Worcestershire where we work. Our nearest city page is Birmingham, about 25 miles away.
Every address in WR6 is covered. That includes homes on Pensax Road and Stockton Road and the roads around them. Neighbouring places we cover include Elms Green (1 mile south-east), Pensax (1 mile north), Menithwood (1 mile north-west), Eardiston (2 miles west) and Clows Top (3 miles north). We also work in nearby towns such as Worcester (11 miles south-east), Kidderminster (9 miles north-east), Bromsgrove (15 miles east), Great Malvern (13 miles south), Droitwich Spa (11 miles east) and Stourport-on-Severn (6 miles north-east).
Landmarks near Stockton on Teme
Typical jobs here are in homes near Church of St Andrew and The Elms Hotel. Other landmarks nearby include Eastham Bridge mound (3.8 miles west). Green spaces nearby include Abberley Hill and Hunthouse Wood.
About our accreditations · Every repair comes with a one-year guarantee.
