Pembrokeshire · Wales
Bath chip & crack repair in Sardis, Pembrokeshire
Chip and crack repairs to enamel, acrylic and cast iron baths in Sardis, carried out at your home and guaranteed for a year.
- Repairs from £95
- Damage done while the bathroom was being fitted
- Deep scratches in acrylic
Bath repair at your home in Sardis
We repair just the damaged spot and colour-match it to the bath, which costs far less than replacing a fitted bath and the tiles around it. Most baths can be used again the following day. Whether it’s snagging damage from a refit and deep scratches in acrylic, we can help, on pressed steel enamel, acrylic and whirlpool & spa baths alike.
You get a one-year guarantee, the same in Sardis as everywhere else we work.
- Area
- Sardis (SA73)
- Area hub
- Pembrokeshire
- Cover
- A year, on every repair
- Price
- From £95. Fixed and free, based on photos
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Where we work around Sardis
Sardis is about 4 miles north-east of Milford Haven, in Pembrokeshire. We visit clients in Sardis, so you do not need to take anything anywhere. We cover all 223 towns and villages across Pembrokeshire.
Here we cover the SA73 postcode area. We regularly work on streets such as Ashtree Close and Thurston Lane and the roads around them. Other places close to Sardis include Hill Mountain (1 mile east), Trooper's Inn (1 mile north-west), Newton Mountain (1 mile south-east), Foxhall (1 mile east) and Rosemarket (1 mile west). We also work in nearby towns such as Haverfordwest (4 miles north), Milford Haven (4 miles south-west), Pembroke (5 miles south), Pembroke Dock (3 miles south), The Marsh (4 miles north) and Dinbych-y-Pysgod (11 miles south-east).
What’s near Sardis
Locally, our jobs take us to homes close to Sardis English Baptist Church and the streets around them. The closest station to Sardis is Johnston station, roughly 2.6 miles north-west. Well-known places in the area include Pembroke Dock Heritage Centre (3.3 miles south) and Rosemarket Rath (1.2 miles south-west). Green spaces nearby include Pembroke River lower and East Moor.
The process
It’s a tidy, low-fuss visit. We agree the arrival time in advance, cover and mask the work area, then carry out the work, which normally takes a few hours. If anything looks different from your photos, we’ll talk to you before going ahead.
- We start by looking at the damage and confirming the plan with you.
- Any rust and loose material comes out, and the area is degreased.
- We build up the filler in layers, shaping it to the bath.
- We tint the finish by hand to match the bath.
- Finally, it’s polished to match the shine and left to cure.
Getting ready for the visit
- Have somewhere for us to park nearby if possible
- Mention any parking restrictions or tricky access
- Tell us about any previous repairs or coatings
How to get a price
The quickest way to a price is to send a couple of photos using our quote form or ring us. We’ll say straight away whether it can be repaired.
Read more
Can I fix it myself?
It’s natural to want to try a repair yourself. The risk is that a kit repair hides the damage for a while, then fails, and then the old filler has to be removed first.
The difference between a kit and a professional repair is mostly in the preparation and colour. We prepare the area properly, mix the colour on site and polish the finish to match, then guarantee it for a year.
Work for landlords and builders
We carry out planned and one-off repairs for housing associations and facilities teams. A repair avoids taking out and refitting, which is easier on the people living there.
We regularly work with letting and managing agents. Send the address, pictures and access details.
When we would advise against a repair
Some problems need a builder, plumber or fitter rather than us:
- A bath worn all over, where resurfacing makes more sense
- Leaking fittings, which need a plumber
- Cracks in acrylic we can’t reach from underneath
Not sure? Send pictures and we’ll give you a straight answer before booking.
Materials we work on in Sardis
- Whirlpool & spa baths
- Pressed steel enamel
- Roll-top & freestanding
- Cast iron enamel
- Acrylic
Aftercare tips
Once the work has cured, treat it gently:
- Keep abrasive pads and gritty cleaners away from the bath
- Store metal items away from the bath
- Rinse it down after each bath
- Clean with warm water and a mild detergent
Care for the repair the same way as the bath: warm water, washing-up liquid and a soft cloth. Keep scouring pads and gritty cleaners away from it.
Tape over a fresh chip or crack until it’s repaired, to keep water out. Take it off before we arrive.
Repair or replace: which is better?
A new bath brings a chain of other jobs: the tiles sitting on the rim tend to break, a new panel is frequently needed, and the plumbing has to be disconnected and refitted. A repair skips all of it. Our bath repair starts from £95. Instead of hourly rates, we price the whole job up front. It depends on the damage, the material and access, and doing several items at once reduces it.
What you get with us
- CHAS and Constructionline accredited
- One visit for most repairs
- Every repair guaranteed for a year
- Free fixed quotes from pictures
See our pricing and bath cost comparison.
FAQs for Sardis
What happens if you find more damage?
It’s rare, but if it happens we talk to you first. The price only changes if you agree.
Do you work for landlords and businesses?
Yes. We carry out repairs for homeowners, landlords, letting agents, builders and businesses.
When can I have a bath again?
Generally within a day, though it depends on what we’ve done.
Do you work in Sardis?
Yes. We work across the UK and come to Sardis. Send pictures and we’ll quote, or call 0345 017 0787.
Do you cover the whole of Pembrokeshire?
Across the UK. Our prices are the same everywhere.
I’m a tenant. Can you help?
Yes, but check with your landlord or agent first. Landlords are often glad to have it sorted before the end of a tenancy.
Do I need to be at home?
Yes. The technician needs access to the room for the visit, at a time that suits you.
What happens after I send pictures?
We come back with a fixed quote. There is no obligation to book.
More services for Sardis
Different materials, different repairs
Acrylic
An acrylic bath is a moulded sheet strengthened from below. They don’t rust, but they can crack, scratch or be holed, and cracks need support from behind to stay fixed.
Pressed steel
Steel baths are lighter than cast iron, but have a similar enamel surface. Chips rust quickly on steel, especially around the waste, so repair chips early.
What we are called out for in Sardis
Dropped items cause the majority of chips, and building work is a common culprit. Acrylic baths crack for a different reason: poor support underneath, so the bath flexes when it’s full.
Get in touch if you’ve noticed:
- A cracked acrylic bath
- An old repair that has yellowed or come loose
- Rust spots around the plughole
- Holes from dropped items
Before booking anyone
- Whether the price covers travel
- How long it needs to cure
- What aftercare is recommended
- What prep work is covered
About our accreditations · Every repair comes with a one-year guarantee.
