Pembrokeshire · Wales
Bath Repair in Hill Mountain
Damaged bath in Hill Mountain? We put it right where it is, match it on site and guarantee the work for a year.
- Repairs from £95
- Chips caused by builders
- Impact holes in acrylic
Bath repair at your home in Hill Mountain
We’ve repaired just about every kind of bath damage: chips from dropped bottles, rust round the plughole, cracks in acrylic and holes from falling tools. All of it is repaired where the bath stands with a one-year guarantee. Whether it’s scuffs and scratches in the surface and rust spots around the plughole, we can typically put it right.
We stand behind the work with a one-year guarantee.
- Location
- Hill Mountain (SA62, SA73)
- Region
- Pembrokeshire
- Warranty
- A year, on every repair
- Quote
- From £95. Fixed and free, based on pictures
- Call
- 0345 017 0787
- Updated
- 23 October 2026
Prices and what affects them
Prices start from £95. You will know the full cost before you book. We take into account:
- How much damage there is
- Access to the area
- How hard the colour is to match
- The material and finish
A few things move the price: the amount of damage, the material, access to the area, and how many jobs we do in one trip. Send pictures and you will get a fixed figure.
Send pictures for a quote
Good photos mean an accurate price. Here’s what helps:
- Where you are, by postcode
- A clear, close picture of the problem area
- A coin beside the damage so we can judge size
- Any earlier repairs or coatings
Getting a quote takes a couple of minutes: photograph the damage, then the entire bath, add your postcode and send them to us. You will get a fixed price, not an estimate.
Nearby places to Hill Mountain
What else we do in Hill Mountain
Hill Mountain questions
Do you cover Hill Mountain?
Yes. We work across the UK and come to Hill Mountain. Send us photos for a fixed quote, or call 0345 017 0787.
I tried a repair kit. Can you fix it?
Yes. We remove the old filler and start again. Tell us about it when you send photos.
What happens next?
We look at the pictures and reply with a fixed quote and some dates. If we need another angle, we’ll ask.
How long before I can use the bath?
Normally by the following day, depending on the repair.
What about rust by the waste?
Yes. We take out the rust and any loose enamel, seal and fill the area, then colour-match the finish.
Is there a call-out fee?
Travel is included in the price, with the same prices everywhere we work.
Can you repair several things at once?
Yes. Combining jobs on one visit brings the cost down. Send pictures of everything you’d like done.
Will the price change on the day?
We will show you and explain before doing anything extra. You won’t be charged for anything you haven’t agreed.
Signs you need bath repair in Hill Mountain
Most bath damage comes from something dropped: a shampoo bottle, a shower head, a tile or a tool during a refit. On enamelled baths, any chip down to the metal will start to rust.
The things customers typically mention when they call include:
- Snagging damage from a refit
- Impact holes in acrylic
- A failed DIY repair that is discoloured or lifting
- Cracks in an acrylic bath
Questions to ask before booking
- Who will actually do the work
- Whether the price covers travel
- A fixed price, and whether VAT is included
- What happens if they find more damage
What your bath is made of matters
Cast iron
Cast iron baths are thick and very strong, finished with fired enamel. A chip down to the iron can rust, but the body of the bath lasts a very long time, so it’s always worth repairing.
Composite and resin
Stone resin and composite baths are heavy and solid, and frequently freestanding. Chips and scratches can be filled and colour matched, just like other baths.
When a repair is not the answer
Some jobs aren’t right for a repair, for example:
- A bath that flexes because its feet or cradle have failed (that needs fixing first)
- Acrylic cracks with no access behind them
- Leaking fittings, which need a plumber
Not sure? Send photos and we’ll give you a straight answer before you book.
Surfaces we repair
- Cast iron enamel
- Acrylic
- Roll-top & freestanding
- Whirlpool & spa baths
- Pressed steel enamel
Aftercare tips
Simple care helps the repair last. We recommend:
- Avoid scourers, wire wool and gritty cream cleaners
- Don’t leave a fresh chip for long
- Get a dripping tap fixed promptly
- Put a towel in the bath if you’re working above it
Treat the repaired area like the rest of the bath: a soft cloth and washing-up liquid is all it needs. Avoid scourers and gritty cream cleaners.
Stop using the bath if a crack lets water through. Water under the bath can damage the floor and the ceiling below.
How it works
You don’t need to empty the room beforehand. We bring everything we need with us, lay protective sheets and get going once we have agreed what we’re doing. It generally takes a few hours, depending on the damage, and you can get on with other things while we are there.
- We start by cleaning the damage and taking out loose enamel and rust.
- Next we fill the damage and sand it smooth and level.
- We tint the finish on the day to suit your bath’s shade of white or colour.
- We apply the finish coats and polish the repair so it blends in.
- The repair is left to cure, and most baths can be used the following day.
Before we arrive
- Mention if the room is upstairs or in a flat
- Avoid using the area for a few hours before we arrive
- Mention any parking restrictions or tricky access
How to get a price
Pricing is simple: take a close-up of the damage and a picture from further back, send them over with your postcode, and we will reply with a fixed price. There is no charge for the quote and no obligation.
Advice
Landlords, agents and businesses in Hill Mountain
Letting agents often send us pictures straight from the inventory. You can have a price before you arrange access, and we can arrange access with the tenant directly if that helps.
Housing associations and facilities teams use us for planned and reactive repairs in Pembrokeshire and across the UK. Repairing in place avoids the disruption of a replacement, which is easier on the people living there.
Covering Hill Mountain
Hill Mountain is about 5 miles east of Milford Haven, in Pembrokeshire. Our work suits any type of property, from flats and terraces to detached houses and new builds, as well as offices, shops and holiday lets. Our repair technicians cover all 223 towns and villages in Pembrokeshire.
We work across the SA62 and SA73 postcode area and the streets around it. That includes homes on Ashdale Lane, Elidyr Park and Cleddau Close and the roads around them. If you’re just outside Hill Mountain, we cover Newton Mountain (1 mile south-east), Foxhall (1 mile east), Port Lion (1 mile east), Sardis (1 mile west) and Houghton (1 mile south). Larger places within reach include Haverfordwest (5 miles north-west), Milford Haven (5 miles west), Pembroke (4 miles south), Pembroke Dock (3 miles south), The Marsh (5 miles north) and Dinbych-y-Pysgod (11 miles south-east).
Landmarks near Hill Mountain
Locally, our jobs take us to homes close to Sardis English Baptist Church, Cleddau Reach VC School and The Cottage Inn, among other places. For rail, the closest station is Pembroke Dock station, roughly 3.1 miles south of the centre. A little further out are South Pembrokeshire Hospital (3.3 miles south) and Rosemarket Rath (1.7 miles west). Green spaces nearby include Pembroke River lower and East Moor.
DIY kit or professional repair?
The difference between a kit and a professional repair is mostly in the preparation and colour. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, then guarantee it for a year.
If you’re set on a kit, follow its instructions closely, make sure the area is clean and completely dry, and give it the full curing time. If it fails, we can still put it right.
About our accreditations · Every repair comes with a one-year guarantee.
