Somerset · England
Bath chip & crack repair in Southway, Somerset
Chip and crack repairs to enamel, acrylic and cast iron baths for homes and businesses in Southway and across Somerset. Free, fixed quotes from your pictures.
- Repairs from £95
- Snagging damage from a refit
- Deep scratches in acrylic
Looking after it afterwards
It’s all simple stuff, just a few sensible habits:
- Get a dripping tap fixed promptly
- Rinse the bath after use, especially in hard water areas
- Cover the bath during DIY or decorating
- Keep abrasive pads and gritty cleaners away from the bath
Leave the repair to cure for as long as we say before using the bath. After that, gentle cleaning keeps it looking good.
Don’t leave a chip on a steel or cast iron bath. Once water reaches the metal, rust begins, turning a quick repair into a bigger one.
Bath repair in Southway, done in place
It pays to repair bath damage while it’s small. On steel and cast iron, exposed metal starts to rust, while cracks in acrylic grow each time the bath moves. A repair stops both. Common call-outs are for deep scratches in acrylic and a cracked acrylic bath, across whirlpool & spa baths, cast iron enamel and acrylic.
The work is covered for a year after we finish. If anything is not right, ring us and we’ll come back.
- Location
- Southway (BA5)
- County
- Somerset
- Cover
- A year, on every repair
- Price
- From £95. Fixed and free, based on pictures
- Call
- 0345 017 0787
- Last updated
- 23 October 2026
Repairs by material
Cast iron
Cast iron is heavy and rigid, finished with fired enamel. Chips can rust if left, but the body of the bath lasts a very long time, so it’s always worth repairing.
Acrylic
An acrylic bath is a moulded sheet strengthened from below. There’s no rust, but cracks, holes and scratches happen, and a crack only stays repaired if it’s supported underneath.
Southway: your questions answered
Is a cracked acrylic bath repairable?
Typically, yes, as long as we can get to the back of the crack to support it. Take off the bath panel and check, or send us a photo.
Does someone need to be in?
We need someone to let us in. After that, you can carry on with your day.
What happens if you find more damage?
The price is fixed for what the photos show. If there is more, we will tell you before starting.
Is a repair better than a new one?
Usually, if the item is otherwise sound. Repairing avoids the cost and disruption of replacing. We will tell you honestly if replacement makes more sense.
What areas do you cover?
We work UK-wide. Our prices are the same everywhere.
Are you a vetted contractor?
Yes, including CHAS, Constructionline and SafeContractor. See our accreditations page for the full list.
How much does bath repair cost in Southway?
Repairs from £95. We give a fixed quote based on pictures of the damage. Send a close-up and a photo of the entire item and your postcode.
Can rust on a bath be repaired?
Yes. We take out the rust and any loose enamel, seal and fill the area, then colour-match the finish.
Towns and villages near Southway
Other services in Southway
Southway and the surrounding area
Southway is about 3 miles south-west of Wells, in Somerset. Customers in Southway get the same service as everywhere else we cover: a fixed quote from pictures, then a visit to do the work. Southway is one of 640 towns and villages in Somerset we cover.
Jobs in BA5 work the same way as everywhere else we cover. If you are just outside Southway, we cover Coxley (1 mile north-east), Coxley Wick (1 mile north-east), Upper Coxley (1 mile north-east), Brindham (1 mile south) and Barrow (2 miles east). We also work in nearby towns such as Bridgwater (14 miles west), Burnham-on-Sea (14 miles west), Wells (3 miles north-east), Midsomer Norton (12 miles north-east), Shepton Mallet (6 miles east) and Street (4 miles south-west).
Near you in Southway
Around Southway, we work in homes near St Dunstan's Community School, Christ Church and Coxley Primary School, among other places. Nearby you will also find Glastonbury Lake Village Museum (2.3 miles south-west) and Clarks Village (4 miles south-west). Not far away are Glastonbury Tor and Ham Wall.
Common problems we fix in Southway
Glass and heavy bottles cause more chips than anything else, with dropped shower heads close behind. Fittings cause damage too: water sits around them, and any chip there soon rusts.
You may need us if you’ve spotted any of these:
- Chips under the taps
- Cracks in an acrylic bath
- Impact holes in acrylic
- Scratches you can feel with a fingernail
Comparing quotes
- What aftercare is recommended
- How long it needs to cure
- What happens if the damage is worse than the pictures show
- Whether the price is fixed and includes VAT
Repairing versus replacing in Southway
Cast iron baths especially are worth keeping: they’re very heavy to remove, especially upstairs, and a like-for-like replacement can be expensive. Repairing it leaves it where it is. Our bath repair starts from £95. Instead of hourly rates, we price the entire job up front. It depends on the damage, the material and access.
Why choose Surface Doctor in Southway
- CHAS and Constructionline accredited
- No need to remove anything
- Normally one visit, start to finish
- Colours mixed by hand to suit your surface
See our full price list or bath cost comparison.
Work for landlords and builders
Hotels, guest houses and holiday lets cannot afford rooms out of action for long, so we keep visits short and tidy. We can work around your bookings.
Housing associations and facilities teams use us for planned and reactive repairs. A repair avoids taking out and refitting, which is easier on the people living there.
How the visit works
Your technician turns up at the time we agreed with you and looks over the damage before anything else. Dust sheets and masking tape go down before any work starts. Most visits take a morning or an afternoon, and we leave the room as we found it.
- We start by cleaning the damage and taking out loose enamel and rust.
- We fill the damage and sand it flush with the surrounding surface.
- We mix the colour on the day to match your bath’s exact shade.
- We apply the finish coats and polish the repair so it blends in.
- We leave it to cure; you can usually use the bath the day after.
Getting ready for the visit
- Clear the area around the damage
- Open a window if you can
- Let the surface dry out before the visit
Get a quote
Send us photos of the damage and one of the entire item, with your BA5 postcode, and we’ll come back with a fixed quote.
Read more
DIY kit or professional repair?
It’s tempting to reach for a kit, but the repairs we redo most often are DIY ones that have discoloured or lifted. Doing it properly first is generally the cheaper route.
You can buy a DIY kit for most repairs, and they can make a small mark look better. Where they fall down is colour and preparation: they come in a handful of shades, and if the surface is not prepared the repair will not last.
What a repair cannot fix
Some jobs aren’t right for a repair, including:
- Metal that has corroded all the way through
- A bath worn all over, where resurfacing makes more sense
- A bath that flexes because its feet or cradle have failed (that needs fixing first)
If in doubt, send photos and we will say what we think before you book.
Materials we repair
- Whirlpool & spa baths
- Roll-top & freestanding
- Cast iron enamel
- Acrylic
- Pressed steel enamel
About our accreditations · Every repair comes with a one-year guarantee.
