Oldham · England
Bath Repair for Waterhead homes
Chip and crack repairs to enamel, acrylic and cast iron baths for homeowners, landlords and businesses in Waterhead. Free, fixed quotes from your pictures.
- Repairs from £95
- Rust spots around the plughole
- A cracked acrylic bath
How to look after the repair
How the surface is treated afterwards matters:
- Protect the bath with a towel when doing jobs nearby
- Don’t leave razors or cans standing in the bath
- Get a dripping tap fixed promptly
- Avoid scourers, wire wool and gritty cream cleaners
Keep metal objects like razors and cans off the surface, as they can leave rust marks. A dripping tap should be fixed early, too.
Small chips are quick to repair. Leave them and they collect dirt, stain and, on metal baths, rust, so it’s worth getting them done early.
About our bath repair in Waterhead
Bath repair is our most common job. A chip by the taps, a crack in the base and a rust spot by the plughole are all repaired in place, normally in one visit. Typical jobs include a cracked acrylic bath and damage beneath the taps, across acrylic, pressed steel enamel and roll-top & freestanding.
All of our repairs are guaranteed for twelve months. We return to put right any problem with the work.
- Where
- Waterhead (OL4, OL1, OL2)
- County
- Oldham
- Cover
- One year on every repair
- Quote
- From £95. Free and fixed, from your photos
- Telephone
- 0345 017 0787
- Last updated
- 23 October 2026
Towns and villages near Waterhead
What else we do in Waterhead
How the visit works
We begin by going over the job with you, so there are no surprises. After that, protection goes down around the work area and we start. Allow two to three hours for most chips.
- We protect the bath and the floor around it.
- We clean, key and degrease the damage, and any rust is treated.
- We fill it, let it set, then sand it flush.
- We match both the colour and the shine.
- We clear up and give you the curing time, normally until the next day.
How to prepare
- Point us to the nearest place to park
- Ensure the area is dry
- Tell us if there are stairs or a lift
Get a quote
There is no need for us to visit first. Nearly every job can be priced from photos: we need a close-up, a wider picture and your postcode, and we’ll reply with a fixed quote.
Read more
Signs you need bath repair in Waterhead
Rust typically starts where water sits, by the plughole, beneath dripping taps or in an unrepaired chip. Once water reaches the steel or iron, rust spreads under the enamel.
Keep an eye out for these signs:
- Chips on the rim or sides
- A chip where the taps sit
- Rust by the waste and overflow
- Cracks in an acrylic bath
Questions to ask before booking
- How long it needs to cure
- Whether the colour is mixed to match
- A fixed quote, and whether VAT is included
- Who will actually do the work
What bath repair costs
Prices start from £95. There’s no charge for travel to Waterhead. The price comes down to:
- Any earlier repairs that need removing first
- Access to the area
- How hard the colour is to match
- The material and finish
A few things move the price: the amount of damage, the material, access to the area, and how many jobs we do in one trip. Photos let us give you a fixed figure.
Getting a price from photos
Phone pictures are fine, there is no need for anything special. Ensure they show:
- Whether it’s been repaired or coated before
- The postcode, so we can plan the visit
- Daylight if possible, and no flash reflection
- A clear, close picture of the problem area
Most clients in Waterhead get their price from pictures. Tell us what happened and where you are, and we’ll send back a fixed quote and some dates.
Should I try a DIY kit first?
What a professional repair adds is preparation, colour matching and finishing. We prepare the area properly, mix the colour on site and polish the finish to match, then guarantee it for a year.
If you’ve already tried a DIY fix, that’s fine. We remove the old filler and start again, so it doesn’t stop a professional repair. Just mention it when you send pictures, as it can add time.
Our work in Waterhead
Waterhead is about 1 mile north-east of Oldham, in Oldham. We visit clients in Waterhead and the surrounding area, so you do not need to take anything anywhere. Waterhead is one of 72 places in Oldham where we work. We work right across the region, from Waterhead to Manchester (about 7 miles away).
Here we cover the OL4, OL1 and OL2 postcode area. From Cow Lane, Lees Road and Keats Road or a nearby road, we can come to you. Neighbouring places we cover include Greenacres (1 mile south-east), Clarksfield (1 mile south), Watersheddings (1 mile north), Derker (1 mile west) and Crossbank (1 mile east). Within a short drive, we also cover Chadderton (3 miles west), Failsworth (4 miles south-west), Uppermill (3 miles east), High Crompton (3 miles north-west), Nordens (3 miles west) and Chadderton Park (3 miles west). Waterhead is among the bigger towns we cover in Oldham.
What’s near Waterhead
Locally, our jobs take us to homes close to Counthill School, St Barnabas and Oldham Pupil Referral Unit and the streets around them. Also close by are Shepherds Boy pub (0.5 miles east) and Littlemoor Primary School (under half a mile north). The nearest railway station is Mossley (Manchester) station, roughly 2.9 miles south-east. A little further out are Ashton Hurst (2.7 miles south) and Royal Oldham Hospital (1.6 miles west). Green spaces nearby include Tandle Hill and Eastwood Nature Reserve.
For landlords and businesses
Rental properties take more wear, and replacing things at every changeover adds up. Repairing between tenants keeps the property presentable for less.
Letting agents often send us photos straight from the inventory. You can have a price before you arrange access, and we liaise with tenants about access if you’d like us to.
When a repair isn’t the answer
We’ll always be straight with you, so here’s what a repair will not do:
- Leaks from the waste or overflow fittings (a plumber’s job)
- A bath that moves underfoot, until its support is fixed
- Rust that has eaten right through a steel bath
Not sure? Send photos and we’ll give you a straight answer before you book.
Materials we repair
- Cast iron enamel
- Whirlpool & spa baths
- Roll-top & freestanding
- Pressed steel enamel
- Acrylic
Repairs by material
Acrylic
Acrylic is light and warm to the touch, but it relies on good support. Repairs to cracks are reinforced from the back.
Cast iron
Cast iron is heavy and rigid, finished with fired enamel. A chip down to the iron can rust, but the bath itself lasts for generations, which makes it well worth repairing.
Questions from Waterhead
Is it worth repairing rather than replacing?
Generally, if the item is otherwise sound. Repairing avoids the cost and disruption of replacing. We’ll tell you honestly if replacement makes more sense.
How quickly can you book me in?
Your quote comes with available dates. If it’s urgent, say so and we will do what we can.
Are you accredited?
Yes. Our accreditations include CHAS, Constructionline and SafeContractor. See our accreditations page for the full list.
I rent my home. Can I book you?
We can work for tenants, landlords or agents. Just make sure the landlord agrees.
What if the damage is worse than the pictures show?
It’s rare, but if it happens we talk to you first. The price only changes if you agree.
Is there a guarantee?
Yes, for a year. If there is a problem with the work in that time, we come back and put it right.
Is a cracked acrylic bath repairable?
Normally, yes, if we can reach the underside to reinforce it. Take off the bath panel and check, or send us a picture.
Can you repair something that’s been repaired before?
Generally, yes. We remove the old repair before doing a new one, so mention it when you send photos.
About our accreditations · Every repair comes with a one-year guarantee.
