Hampshire · England
Bath Re-enamelling for Arford homes
Full bath re-enamelling and resurfacing in Arford, carried out at your home and guaranteed for a year.
- Resurfacing from £350
- A bath that stays dull however much you clean it
- Wear marks under the taps
Bath re-enamelling in Arford, done in place
We don’t move the bath, so your taps, tiles and plumbing are left alone. Most baths are done in one visit, and can be used again the day after. Common call-outs are for worn patches where water runs and sits and an original cast iron bath that needs restoring, across acrylic baths, Victorian roll-tops and pressed steel baths.
Whatever the size of the job, you get the same one-year guarantee in Arford and across Hampshire.
- Area
- Arford (GU35)
- County
- Hampshire
- Guarantee
- One year on every repair
- Quote
- From £350. Fixed and free, based on photos
- Telephone
- 0345 017 0787
- Updated
- 23 October 2026
Keeping it looking good
Once the work has cured, treat it gently:
- Have chips seen to early
- Keep suction mats out of the bath
- A quick wipe after use keeps limescale away
- Wash away dyes and oils after use
A quick rinse and wipe after use helps, especially in hard water areas, so limescale cannot build up.
Avoid scrubbing a dull bath with abrasive cleaners. It just wears the enamel further and makes resurfacing more work.
For landlords and businesses
Rental properties take more wear, and replacing items every time a tenant leaves is expensive. Repairing between tenants keeps the property presentable for less.
We work for landlords, letting agents and housing providers in Arford as well as homeowners. A repair between tenants keeps the property empty for less time, and it typically costs far less than a refit.
When we’d advise against a repair
Not everything can be repaired, and we’d rather say so up front. Repairs won’t solve:
- Leaking taps or wastes (a plumber’s job)
- Damage hidden under a previous coating, until it’s stripped back
- An acrylic bath that flexes badly underfoot
If in doubt, send photos and we will say what we think before you book.
Surfaces we repair
- Basins & shower trays
- Acrylic baths
- Victorian roll-tops
- Cast iron baths
- Pressed steel baths
Can I fix it myself?
The difference between a kit and a professional repair is mostly in the preparation and colour. We clean and key the area properly, mix the colour to your surface and finish it to the same sheen, and the work is guaranteed.
You can buy a DIY kit for most repairs, and they can make a small mark look better. The trouble is colour and preparation: they come in a handful of shades, and if the surface isn’t prepared the repair will not last.
Repairing versus replacing in Arford
If you like your bathroom but not your bath’s surface, re-enamelling is the least disruptive fix. Tiles, panels and taps stay put. Resurfacing from £350, with every job priced individually. Most people are surprised how affordable a repair is, particularly next to the cost of replacement. Photos let us give you the exact figure.
What you get with us
- Same prices wherever you are
- Usually one visit, start to finish
- Colour mixed on the day to match
- No need to remove anything
Take a look at our pricing and resurfacing vs replacement cost guide.
Arford and the surrounding area
Arford is about 6 miles south of Farnham, in Hampshire. Jobs in Arford are booked in like any other job: a fixed quote from photos, and a technician at your door on the day. Arford is one of 683 places in Hampshire where we work. You can also see our page for London, about 41 miles away.
Here we cover the GU35 postcode area. We regularly work on streets such as Beech Hill Road, Arford Common and Headley Hill Road and the roads around them. We also cover the places around Arford: Headley (1 mile south-west), Headley Down (1 mile east), Lindford (1 mile west), Standford (1 mile south-west) and Wishanger Common (2 miles north). Larger places within reach include Farnborough (12 miles north), Fleet (11 miles north), Aldershot (9 miles north), Alton (7 miles west), Petersfield (10 miles south-west) and Yateley (15 miles north).
Around Arford
Our clients here include homes close to The Holly Bush Inn, Mill Chase Academy and The Holme Church of England Primary School and the streets around them. For rail, the closest station is Liphook station, about 3.6 miles south. Nearby you’ll also find Chase Community Hospital (2.3 miles south-west). For a walk, there is Deadwater Valley and Gibbet Hill.
How it works
From the moment we arrive, we keep the work contained to the one room. Surfaces nearby are masked off, the work takes a full day, depending on what we find, and we finish by cleaning up and talking you through the result.
- We sheet, mask and ventilate the room.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- We key the bath and apply a bonding primer.
- Several coats of finish are sprayed on, then it cures until the next day.
Before we arrive
- Let the surface dry out before the visit
- Tell us about any previous repairs or coatings
- Point us to the nearest place to park
Get a quote
We price from pictures so you do not have to wait in for a survey. Send them through the quote form, or call 0345 017 0787 if you’d rather talk it through.
Related advice
Questions from Arford
How do I get a price for bath re-enamelling in Arford?
Resurfacing from £350. Because every job differs, we price from photos. You know the full cost before anything is booked.
How quickly can you book me in?
Your quote comes with available dates. If it’s urgent, say so and we will do what we can.
Do you come to Arford?
We do. We send a technician to Arford for every job, with no extra charge for travel.
Which areas do you work in?
Across the UK, so Arford is covered. Prices do not change with location.
Are you accredited?
Yes, including CHAS, Constructionline and SafeContractor. See our accreditations page for the full list.
Are there extra charges for Arford?
There’s no separate call-out charge. The fixed quote covers the visit and the work.
Will you leave a mess?
Dust sheets and masking go down before we start, and tidy up before we leave.
Will the new finish last?
A well-prepared finish lasts a long time if it’s looked after. Avoid abrasive cleaners and suction mats.
Common problems we fix in Arford
The gloss on enamel is thin, and every scrub with an abrasive cleaner takes a little away. Eventually the surface turns porous and stains.
Common reasons people in Arford contact us are:
- Thin, worn enamel in places
- A roll-top that’s seen better days
- An old resurfacing that is failing
- Several chips and rust patches
Questions to ask before booking
- If travel is included in the price
- Whether they match the colour on site
- How the room is protected while they work
- How changes to the job are handled
Towns and villages near Arford
Other services in Arford
Materials and what they mean for the repair
Pressed steel
Steel baths re-enamel well, as long as any rust is dealt with first. Steel frequently rusts by the plughole, so we check it carefully.
Roll-top and period baths
We can resurface a roll-top inside and out, and the outside can be refinished too.
About our accreditations · Every repair comes with a one-year guarantee.
