Argyll and Bute · Scotland
Bath Re-enamelling for Bullwood homes
Damaged bath in Bullwood? We repair it in place, mix the colour on the day and guarantee the work for a year.
- Resurfacing from £350
- A bath in a colour that no longer suits
- A dull, rough surface that won’t come clean
Repair or replace in Bullwood?
A new bath means a plumber, removing a heavy bath, re-tiling or making good the walls and several days without a working bathroom. Resurfacing gives the bath a new finish with the bath left where it is. Prices start from £350. Every job is a little different, so we price each one individually. The size and type of damage, the material and access all play a part, and combining jobs on one visit brings the cost down.
What you get with us
- Rooms protected and left tidy
- Colour mixed on the day to match
- Every repair guaranteed for a year
- Work done at your home or business
See our prices page and bath cost comparison.
About our bath re-enamelling in Bullwood
If your bath is sound but looks tired, resurfacing is normally the best value. There’s no removal, plumbing or tiling involved. Typical jobs include a dull, rough surface that won’t come clean and a roll-top that’s seen better days, on cast iron baths, Victorian roll-tops and acrylic baths.
You get a one-year guarantee, the same in Bullwood as everywhere else we work.
- Location
- Bullwood (PA23)
- Area hub
- Argyll and Bute
- Warranty
- A year, on every repair
- Quote
- From £350. Free and fixed, from your photos
- Phone
- 0345 017 0787
- Page updated
- 23 October 2026
When to call us in Bullwood
Enamel wears gradually. Years of cleaning, hard water and hot baths wear the gloss away, starting where water runs and sits.
Signs it’s time to call us include:
- A bath that stays dull however much you clean it
- A peeling or bubbling previous coating
- Brown or grey marks that don’t clean off
- Several chips and rust patches
Before you book anyone
- What protection goes down before work starts
- If travel is included in the price
- Whether cleaning and preparation are in the price
- How the colour is matched
Landlord and trade work in Bullwood
We work for landlords, letting agents and housing providers in Bullwood as well as householders. Repairing between tenancies keeps void periods short, and it costs much less than replacing.
Rented homes see more wear and tear, and replacing items every time a tenant leaves is expensive. Repairing between tenants keeps the property presentable for less.
Bullwood: your questions answered
Do the materials smell?
A little, depending on the job. Open windows and an extractor fan help, and it soon fades.
How long does re-enamelling take?
One day for most baths, ready the following day. We will confirm timings when we quote.
How much does bath re-enamelling cost in Bullwood?
Prices start from £350. The exact price depends on the damage, so we quote from photos. You will get a fixed figure before booking.
What happens after I send pictures?
We come back with a fixed quote. There is no obligation to book.
Can you price it without visiting?
In nearly every case. If photos do not show enough, we’ll ask for another angle.
Can you repair several things at once?
Yes. Doing several items on one visit typically costs less than separate visits. Include photos of each item.
Is it safe with children and pets around?
Just keep them out of the work area. We will let you know when it’s safe to use again.
How long does re-enamelling last?
It depends on preparation, use and care. Properly prepared and looked after, it lasts well, and our work is guaranteed for a year.
How we price bath re-enamelling
Prices start from £350. Prices are worked out job by job. The main factors are:
- Doing more than one item at once
- The type of damage
- The colour and finish to match
- The material and finish
A repair is priced on what needs doing, not where you live. The full price is agreed before you book, with no extras added later.
Send pictures for a quote
When you take your pictures, these tips help us give you a firm price:
- A clear, close picture of the problem area
- Any details about the material
- One picture of the whole bath
- The postcode, so we can plan the visit
Getting a price is easy: take a close-up of the damage and a photo from further back, send them over with your postcode, and we’ll reply with a fixed price. There is no charge for the quote and you’re under no obligation.
How the visit works
You don’t need to empty the room beforehand. We bring everything we need with us, lay protective sheets and get going once we’ve agreed what we are doing. It typically takes the best part of a day, and you’re welcome to carry on with your day while we work.
- We check the bath and agree the finish with you.
- Taps, tiles and the floor are masked off.
- The bath is degreased, repaired and keyed.
- We apply the primer and then the finish coats.
- We remove the masking, tidy up and give you the curing time.
Preparing for the visit
- Let the surface dry out before the visit
- Clear toiletries, mats and anything else from around the area
- Keep children and pets away from the room on the day
How to get a price
Getting a quote takes a couple of minutes: photograph the damage, then the entire bath, add your postcode and send them over. You will get a fixed price, not an estimate.
Read more
How to look after the repair
So the finish stays in good condition:
- Leave the bath for the full curing time before using it
- Stick to gentle, non-abrasive cleaners
- Don’t let dyes or oils sit on the finish
- A quick wipe after use keeps limescale away
Give the finish its full curing time before using the bath. Then, gentle cleaning with a soft cloth is enough.
If a previous coating is starting to peel, do not pick at it. Water gets under it and the damage spreads, so have it stripped and resurfaced.
When a repair isn’t the answer
To be straight with you, there are a few things a repair won’t fix:
- An acrylic bath that flexes badly underfoot
- Steel that has corroded right through
- A bath split right through the body
If in doubt, send photos and we will say what we think before booking.
Surfaces we repair
- Cast iron baths
- Victorian roll-tops
- Basins & shower trays
- Acrylic baths
- Pressed steel baths
Bullwood and nearby
Bullwood is about 6 miles west of Greenock, in Argyll and Bute. Anywhere in PA23, we carry out the work at your property. Bullwood is one of 118 towns and villages in Argyll and Bute where we work. Our jobs stretch from Bullwood to Glasgow (about 26 miles away).
Jobs in PA23 are booked in the same way as anywhere else. Streets in the area include Tigh na Cladach, Gerhallow and Bullwood Road, and we cover them all. If you’re just outside Bullwood, we cover Dunoon (2 miles north), Kirn (2 miles north-east), Hunters Quay (3 miles north-east), Sandbank (3 miles north) and Strone (4 miles north). Within a short drive, we also cover Helensburgh (10 miles north-east), Rothesay (8 miles south-west), Rhu (9 miles north-east), Garelochhead (11 miles north), Port Bannatyne (7 miles south-west) and Innellan (3 miles south). Remote and island addresses take a little more planning, so call us to arrange it.
Local landmarks in Bullwood
Locally, our jobs take us to homes close to Dunoon Grammar School, Holy Trinity Church and Dunoon Primary School And Janitor's House, among other places. Bullwood’s nearest station is Inverkip station, roughly 3.2 miles south-east. Well-known places in the area include Castle House Museum (1 mile north-east) and Dunoon Castle (0.9 miles north-east). Not far away are Loch Loskin.
Places near Bullwood
Other services in Bullwood
What your bath is made of matters
Pressed steel
Pressed steel baths take a new finish well, as long as any rust is dealt with first. Rust around the waste is common on steel, so we pay close attention there.
Acrylic
Acrylic is light and warm to the touch, but it needs firm support underneath. Repairs to cracks are reinforced from the back.
About our accreditations · Every repair comes with a one-year guarantee.
