Pembrokeshire · Wales
Bath re-enamelling & resurfacing in Burton, Pembrokeshire
Fixed-price bath re-enamelling in Burton and the surrounding area, done in a single visit in most cases.
- Resurfacing from £350
- Staining under the taps and around the waste
- A roll-top that is seen better days
Bath re-enamelling in Burton, done in place
The bath stays where it is, so the taps, tiles and plumbing are not touched. It usually takes one visit, and can be used again the following day. Our technicians work on acrylic baths, pressed steel baths and cast iron baths, and people most frequently call us about enamel that’s lost its shine and feels rough and wear marks under the taps.
All our work comes with our one-year guarantee, wherever you are in Pembrokeshire.
- Location
- Burton (SA73)
- Region
- Pembrokeshire
- Guarantee
- One year on every repair
- Quote
- From £350. Free, fixed quote from pictures
- Call
- 0345 017 0787
- Last updated
- 23 October 2026
Where we work around Burton
Burton is about 5 miles east of Milford Haven, in Pembrokeshire. Jobs in Burton are booked in like any other job: a fixed price from your pictures, and a technician at your door on the day. We cover all 223 towns and villages across Pembrokeshire.
Our visits in SA73 work the same way as everywhere else we cover. From Church Road, Meadow Park and Hawn Lake or anywhere nearby, a technician can come to you. Nearby, we also work in Burton Ferry (1 mile west), Pembroke Ferry (1 mile south-west), Houghton (1 mile north), Neyland (1 mile west) and Great Honeyborough (1 mile west). Larger places within reach include Haverfordwest (7 miles north), Milford Haven (5 miles west), Pembroke (3 miles south), The Marsh (6 miles north), Dinbych-y-Pysgod (10 miles east) and The Green (9 miles east).
What’s near Burton
Our clients here include homes close to Ysgol Harri Tudur/Henry Tudor School, The Stable Inn and Church Of Saint Mary, among other places. For rail, the closest station is Pembroke Dock station, about 1.5 miles south-west. Further afield, we also cover the area around Benton Castle (1.6 miles north-east) and Pembroke Dock: Llanion (1.3 miles south). Open spaces near Burton include Pembroke River lower and Ferry Wood.
Repairing versus replacing in Burton
A refit takes several trades and several days. Resurfacing is one technician, normally in a day, and the bath can be used the day after. Our bath re-enamelling starts from £350. No two jobs are quite the same, so each one is priced on its own. What’s damaged, how badly and how easy it is to reach all play a part, and combining jobs on one visit brings the cost down.
Why us?
- Technicians who travel to you, UK-wide
- One price list for the entire UK
- Straight answers about what a repair can do
- One visit for most repairs
Read our full price list or resurfacing vs replacement cost guide.
Questions from Burton
Which areas do you work in?
Across the UK, and that includes Burton. Prices don’t change with location.
Does re-enamelling smell?
There is some smell while the coating is applied, so we ventilate the room. It clears as the finish cures.
When can you do it?
It depends on the time of year and where you are. Send photos with your postcode and we’ll reply with the earliest dates.
Someone resurfaced my bath and it’s peeling. Can you help?
In most cases. We strip the failing coating and resurface it properly. Mention it when you send pictures.
Will it make a mess?
No. The work area is masked and covered, and we take our waste away with us.
Do the materials smell?
There can be some smell while we work, so we ventilate the room. It clears as the materials cure.
It’s been repaired before. Can you still fix it?
Generally, yes. Tell us what was done before and we’ll plan for it.
Do you resurface freestanding baths?
Yes, frequently. We resurface the inside, and the outside can be refinished too.
Do you need bath re-enamelling in Burton?
Previous coatings can fail too, lifting by the plughole or blistering. We strip what’s failing and start again.
Typical reasons for a call-out include:
- Worn patches where water runs and sits
- Staining under the taps and around the waste
- Lots of chips and rust spots
- A coating lifting around the plughole
What to look for in a quote
- What preparation is included
- How long the guarantee is and what it covers
- Whether a trained technician does the job
- How the colour is matched
What bath re-enamelling costs
Resurfacing from £350. We price every job individually, from your photos. The main factors are:
- How many areas need work
- How hard the colour is to match
- What the surface is made of
- Where the damage is and how we get to it
A repair is priced on what needs doing, not where you live. You’ll see the full price before you book, with no extras added later.
Getting a price from pictures
Almost every job we do is priced from pictures. This is what we need:
- Any details about the material
- The postcode, so we can plan the visit
- Good light, ideally daylight, without flash glare
- A close-up of the damage, in focus
Upload a picture of the damage and one of the whole item, with your SA73 postcode, and we will reply with a fixed price.
Also near Burton
What else we do in Burton
Should I try a DIY kit first?
Kits are cheap and easy to find, but the repairs we redo most often are DIY ones that have discoloured or lifted. Getting it right first time is typically cheaper.
DIY kits are sold for most surfaces, and they can tidy up a tiny mark. The trouble is colour and preparation: they come in a handful of shades, and if the surface isn’t prepared the repair won’t last.
What your bath is made of matters
Acrylic
We resurface acrylic baths as well, with a coating system suited to acrylic. The bath needs to be firm and well supported for the finish to last.
Pressed steel
Pressed steel baths take a new finish well, as long as any rust is dealt with first. Steel often rusts by the plughole, so we pay close attention there.
What a repair can’t fix
Some jobs are not right for a repair, including:
- Anything hidden under an old coating, until we remove it
- A poorly supported acrylic bath, until it’s firmed up
- A bath split right through the body
If in doubt, send pictures and we’ll say what we think.
What we work on
- Acrylic baths
- Pressed steel baths
- Cast iron baths
- Basins & shower trays
- Victorian roll-tops
What happens on the day
Once we’re through the door, the aim is to do the job without disturbing the rest of your home. Surfaces nearby are masked off, the work takes most of the day, and we finish by cleaning up and talking you through the result.
- We sheet, mask and ventilate the room.
- We remove the old silicone and deep clean the bath.
- Chips, rust and pitting are repaired.
- The surface is keyed and primed for the new finish.
- The new finish is sprayed on in several coats and left to cure until the day after.
Preparing for the visit
- Clear the area around the damage
- Keep a parking space free if you can
- Tell us if there are stairs or a lift
Get a quote
Most clients in Burton get their price from pictures. Tell us what happened and where you are, and we’ll reply with a fixed quote and the earliest dates we have.
Advice
Aftercare tips
To keep it looking its best for years:
- Use washing-up liquid and a soft cloth
- A quick wipe after use keeps limescale away
- Get any chip repaired quickly
- Avoid suction-cup mats
Rinse away dyes, oils and bath bombs straight after use, as they can stain. Fix dripping taps quickly.
Do not try to scrub a worn bath back to shine. It just wears the enamel further and makes resurfacing more work.
About our accreditations · Every repair comes with a one-year guarantee.
