Gloucestershire · England
Bath Re-enamelling for Ebrington homes
Problem with your bath in Ebrington? We put it right where it is, match it on site and back it with a one-year guarantee.
- Resurfacing from £350
- An outdated colour you’d like to change
- Worn patches where water runs and sits
Our work in Ebrington
Ebrington is about 9 miles east of Evesham, in Gloucestershire. We agree a date that works for you, and we will give you an arrival time in advance, so you are not left waiting in all day. We work in 470 places across Gloucestershire, from the larger towns to small villages. Our jobs stretch from Ebrington to Birmingham (29 miles away).
All of GL55 is within our area, from the main roads to the quietest streets. That includes homes on Saxon Fields, Nash's Lane and New Road. Close by, we cover Paxford (2 miles south), Broad Campden (2 miles south-west), Chipping Campden (2 miles west), Northwick Park (2 miles south-west) and Draycott (3 miles south). We also work in nearby towns such as Moreton-in-Marsh (5 miles south), Winchcombe (12 miles south-west), Bourton-on-the-Water (12 miles south), Stow-on-the-Wold (9 miles south), Upper Rissington (13 miles south) and Mickleton (3 miles north-west).
Landmarks near Ebrington
We visit homes around Chipping Campden School and Church of St Eadburga and the streets around them. Ebrington’s nearest station is Moreton-In-Marsh station, about 4.8 miles south of the centre. A little further out are Court Barn (2.1 miles west) and Ellen Badger Hospital (4.5 miles east). Not far away are Dover's Hill.
Bath re-enamelling at your home in Ebrington
Resurfacing renews the entire surface of the bath without a refit. It’s the answer when the whole bath is tired rather than one spot. We are often asked to fix a coating lifting around the plughole and wear marks under the taps, across cast iron baths, pressed steel baths and acrylic baths.
All our work is covered by a one-year guarantee.
- Area
- Ebrington (GL55)
- County
- Gloucestershire
- Cover
- One year on every repair
- Quote
- From £350. Free, fixed price from pictures
- Telephone
- 0345 017 0787
- Last updated
- 23 October 2026
Aftercare tips
So the finish stays in good condition for years:
- Don’t use the bath until it has fully cured
- Stick to gentle, non-abrasive cleaners
- Store bottles off the bath
- Fix dripping taps quickly
A quick rinse and wipe after use helps, especially in hard water areas, to stop limescale building up.
Rust spots on a worn bath get worse with time. Resurfacing before they spread keeps it simpler.
For landlords and businesses
Hospitality businesses need rooms back in use quickly, so most of our work is done in a single visit. We will fit around changeovers where we can.
Rented homes see more wear and tear, and replacing items every time a tenant leaves is expensive. A repair between tenancies is a cheaper way to keep the property in good order.
Also near Ebrington
Also in Ebrington
Your questions about bath re-enamelling in Ebrington
What happens after I send pictures?
We check the damage, the material and your postcode, then reply with a quote and the next dates we have.
Can you repair several things at once?
Yes. Combining jobs on one visit brings the cost down. Include photos of each item.
Is there any odour?
There can be some smell while we work, so we ventilate the room. It fades as everything cures.
Are you accredited?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
Is it safe with children and pets around?
Yes, as long as they stay out of the room we are working in. We’ll let you know when it’s safe to use again.
Do I need to be at home?
Yes. We need access to the room while we work, at a time that suits you.
What do you need from me?
Just photos, your postcode and a contact number. On the day, access to the room.
Can you re-enamel a roll-top bath?
Yes, roll-tops are a big part of our work. We resurface the inside, and the outside can be refinished too.
How it works
A typical visit goes like this: we arrive on time, protect everything around the work area, carry out the work and clear up. Allow most of the day. Before we go, we’ll explain how long to leave it and what to avoid for the first few days.
- The room is masked, protected and ventilated.
- Next we degrease the bath and fix chips and rust spots.
- We prepare the surface and apply a bonding primer.
- Several coats of new finish are sprayed on.
- We leave it to cure, and it’s usually ready the next day.
Preparing for the visit
- Move bottles, mats and clutter away from the area
- Have somewhere for us to park nearby if possible
- Let us know which floor the room is on
Ask for a price
There is no need for us to visit first. Nearly every job can be priced from pictures: we need a close-up, a wider picture and your postcode, and we’ll reply with a fixed price.
Read more
Should I try a DIY kit first?
The difference between a kit and a professional repair is mostly in the preparation and colour. We prepare the area properly, mix the colour on site and polish the finish to match, then guarantee it for a year.
A kit can be fine for a tiny mark out of sight. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, it’s worth having it done properly.
When to call us in Ebrington
Older baths often have several problems at once: worn patches, chips, rust spots and stains. Re-enamelling deals with all of them in one go.
These are the problems we are asked about most:
- A coloured bath you want in white
- An old resurfacing that is failing
- A roll-top that’s seen better days
- Lots of chips and rust spots
Questions to ask before booking
- How changes to the job are handled
- How to care for the finish
- What prep work is covered
- How soon you can use it again
Why repair rather than replace?
For a sound bath, resurfacing costs far less than replacement, when you count removal, plumbing, tiling and decorating. It’s also far quicker. Resurfacing from £350, with every job priced individually. Compared with replacing, repairing usually costs far less, because nothing has to be taken out, refitted or made good. Your fixed quote shows exactly what’s included.
Why us?
- Everything repaired in place
- Straight answers about what a repair can do
- Colour mixed on the day to match
- Most jobs done in one visit
Take a look at our prices page and guide to resurfacing and replacement costs.
Repairs by material
Acrylic
Acrylic is light and warm to the touch, but it needs firm support underneath. Cracks are strengthened from behind before the front is finished.
Roll-top and period baths
Freestanding roll-tops can be done inside and out, with the outside refinished as well.
What a repair cannot fix
A few problems are outside what a surface repair can do:
- A cast iron or steel bath that’s cracked right through
- Holes rusted through the metal
- Damage hidden under a previous coating, until it’s stripped back
Not sure? Send pictures and we’ll give you a straight answer before you book.
Materials we repair
- Cast iron baths
- Basins & shower trays
- Pressed steel baths
- Victorian roll-tops
- Acrylic baths
About our accreditations · Every repair comes with a one-year guarantee.
