Argyll and Bute · Scotland
Bath Re-enamelling in Kilmelford
Local bath re-enamelling for Kilmelford: photo quotes, tidy work and a year’s guarantee.
- Resurfacing from £350
- A peeling or bubbling previous coating
- Stains that will not shift
Bath re-enamelling in Kilmelford without replacing anything
When a bath is structurally fine but worn out on the surface, re-enamelling is usually the most cost-effective option. It avoids removal, plumbing and re-tiling. Our technicians work on pressed steel baths, basins & shower trays and cast iron baths, and the jobs we see most are thin, worn enamel in places and staining under the taps and around the waste.
Peace of mind is built in: each job carries a one-year guarantee, and we explain what it covers before you book.
- Where
- Kilmelford (PA34)
- County
- Argyll and Bute
- Guarantee
- One year on every repair
- Price
- From £350. Fixed and free, based on pictures
- Phone
- 0345 017 0787
- Updated
- 23 October 2026
Prices and what affects them
Prices start from £350. We price every job individually, from your pictures. The main factors are:
- Any earlier repairs that need removing first
- Where the damage is and how we get to it
- How hard the colour is to match
- What the surface is made of
Instead of hourly rates, we price the entire job up front. It depends on the damage, the material and access, and combining items on one visit brings it down.
How to get a fixed price
A couple of clear pictures is all it takes. Try to include:
- Any details about the material
- One sharp close-up of the damage
- A photo taken from further back
- Where you are, by postcode
A quote takes minutes to ask for: photograph the damage, then the entire bath, add your postcode and send them over. What comes back is a fixed price, not a guess.
Places near Kilmelford
More services for Kilmelford
What we do, step by step
We begin by going over the job with you, so there are no surprises. Next, we cover and mask everything nearby and we start. You can expect it to take the best part of a day, and we will keep you posted as we go.
- We sheet, mask and ventilate the room.
- Old sealant is cut out and the bath is deep cleaned.
- Chips, rust and pitting are repaired.
- The surface is keyed and primed for the new finish.
- The new finish is sprayed on in several coats and left to cure until the following day.
Getting ready for the visit
- Let us know if it has been repaired before
- Mention if the room is upstairs or in a flat
- Avoid using the area for a few hours before we arrive
How to get a price
There is no need for us to visit first. Nearly every job can be priced from photos: send a close-up, a wider shot and your postcode, and we’ll reply with a fixed price.
Read more
Our work in Kilmelford
Kilmelford is about 34 miles north-west of Helensburgh, in Argyll and Bute. We agree a date that works for you, and you will know when to expect us, so there’s no waiting around. We cover all 118 towns and villages in Argyll and Bute. Our nearest city page is Glasgow, about 54 miles away.
Our visits in PA34 are booked in the same way as anywhere else. We also cover the places around Kilmelford: Barravullin (4 miles south-west), Craobh Haven (4 miles south-west), Clachan Seil (6 miles north-west), Ardfern (6 miles south-west) and Ellenabeich (6 miles west). We also work in nearby towns such as Oban (11 miles north), Ceann Loch Gilb (15 miles south), Lochgilphead (15 miles south), Dunollie (11 miles north), Dunbeg (13 miles north) and Inbhir Aora (15 miles east). For island and remote addresses, call first so we can plan the visit.
Near you in Kilmelford
Our clients here include homes close to Kilmelford Parish Church. A little further out are Caisteal na Nighinn Ruaidhe (4.3 miles east). For a walk, there’s Loch a' Phearsain and Càrn Dearg.
How to look after the repair
Much of the damage we repair could have been avoided. These habits help:
- Fix dripping taps quickly
- Do not let dyes or oils sit on the finish
- Dry the bath after use to stop limescale
- Use washing-up liquid and a soft cloth
Dry the bath after use if possible, and rinse off any bath products.
Worn enamel only gets rougher with time, and any rust spreads underneath. Resurfacing sooner means less repair work first.
What a repair cannot fix
We’d rather lose a job than do one that will not last, so here’s what a repair can’t put right:
- Problems we can’t see until an old finish comes off
- A cast iron or steel bath that’s cracked right through
- Leaking taps or wastes (a plumber’s job)
Not sure? Send photos and we will give you a straight answer.
Materials we repair
- Pressed steel baths
- Cast iron baths
- Acrylic baths
- Victorian roll-tops
- Basins & shower trays
What your bath is made of matters
Acrylic
Acrylic baths can be resurfaced too, with a coating system suited to acrylic. The bath needs to be firm and well supported.
Cast iron
Cast iron baths are the classic candidate for re-enamelling. The body lasts for generations; only the enamel wears, so a new finish makes them look new again.
Repair or replace in Kilmelford?
A replacement often means several trades over several days. Re-enamelling is one technician, typically one day, and the bath is usable the day after. Prices start from £350. We don’t add extras on the day. The price we quote from your pictures is the price you pay, and if the damage turns out to be different, we discuss it before starting.
Why choose Surface Doctor in Kilmelford
- No need to remove anything
- Dust sheets down, tidy finish
- Generally one visit, start to finish
- We come to you, anywhere in the UK
Read our pricing and resurfacing vs replacement cost guide.
Should I try a DIY kit first?
What a professional repair adds is preparation, colour matching and finishing. We prepare the area properly, mix the colour on site and polish the finish to match, and the work is guaranteed.
A kit can be fine for a tiny mark out of sight. For anything you look at every day, anything that has rusted, cracked or holed, or anything on a coloured surface, it’s worth having it done properly.
Do you need bath re-enamelling in Kilmelford?
Previous coatings can fail too, lifting by the plughole or blistering. We strip what’s failing and start again.
Customers generally contact us about:
- Several chips and rust patches
- A period or roll-top bath worth keeping
- Stains that won’t shift
- A coating lifting around the plughole
Questions to ask before you book
- What prep work is covered
- What protection goes down before work starts
- Aftercare advice
- What happens if the damage is worse than the pictures show
Common questions in Kilmelford
Is it safe with children and pets around?
On the day, the room should be kept clear of pets and children.
How much does bath re-enamelling cost in Kilmelford?
Prices start from £350. We give a fixed price from your pictures. Send a close-up of the damage and a wider photo and your postcode.
Do you work in Kilmelford?
We do. We send a technician to Kilmelford for every job, and the price is the same as everywhere else.
Will you leave a mess?
Dust sheets and masking go down before we start, and we clean up when we have finished.
Will the price change on the day?
The price is fixed for what the photos show. If there is more, we’ll tell you before starting.
Do you resurface freestanding baths?
Yes, roll-tops are a big part of our work. The inside is resurfaced, and we can refinish the outside as well.
It’s been repaired before. Can you still fix it?
Yes, regularly. Removing the old work can add time, and that’s in the quote.
Can I get a quote without a visit?
Yes, almost always. A close-up and a wider photo are enough to give a fixed price.
About our accreditations · Every repair comes with a one-year guarantee.
