Cumbria · England
Bath re-enamelling & resurfacing in Low Hesket, Cumbria
We travel to Low Hesket for full bath re-enamelling and resurfacing. Everything is done in place, and the work is guaranteed.
- Resurfacing from £350
- A bath that stays dull however much you clean it
- An outdated colour you’d like to change
Bath re-enamelling in Low Hesket, done in place
Cast iron, steel, acrylic, roll-top and period baths can all be resurfaced. The finish is sprayed on in several coats over a bonding primer, after the bath has been cleaned, repaired and keyed. If you’re dealing with stains that won’t shift and enamel that’s lost its shine and feels rough, we can help, whatever the material.
We guarantee the work for a year. If something is not right in that time, we come back and put it right.
- Location
- Low Hesket (CA4)
- Area hub
- Cumbria
- Warranty
- A year, on every repair
- Price
- From £350. Free, fixed quote from pictures
- Phone
- 0345 017 0787
- Last updated
- 23 October 2026
Why repair rather than replace?
If you like your bathroom but not your bath’s surface, re-enamelling is the least disruptive fix. Nothing else is disturbed. Prices start from £350. We don’t add extras on the day. What we quote from your photos is what you pay, unless the damage turns out to be different, in which case we talk to you first.
Why book with us
- Dust sheets down, tidy finish
- Everything repaired in place
- Most jobs done in one visit
- Every repair guaranteed for a year
See our full price list or bath cost comparison.
DIY repairs versus a professional job
If you’ve already tried a DIY fix, that’s fine. We remove the old filler and start again, so it doesn’t stop a professional repair. Just mention it when you send photos, as it can add time.
If you are set on a kit, follow its instructions closely, and don’t use it until it has fully cured. If it doesn’t work out, we can still repair it properly.
How we price bath re-enamelling
Prices start from £350. Every quote is fixed and free. What we take into account:
- Whether it’s a chip, crack, burn or wear
- Doing more than one item at once
- Access to the area
- How many areas need work
A few things move the price: the amount of damage, the material, access to the area, and how many jobs we do in one trip. Photos let us give you a fixed figure.
How to get a fixed quote
Phone photos are fine, there’s no need for anything special. Just ensure we can see:
- Any details about the material
- Something in shot to show the size
- A wider photo showing the whole bath
- Daylight if possible, and no flash reflection
Upload pictures of the damage and a wider shot of the entire item, with your CA4 postcode, and we will come back with a fixed quote.
Low Hesket and the surrounding area
Low Hesket is about 7 miles south-east of Carlisle, in Cumbria. Jobs in Low Hesket are booked in like any other job: a fixed quote from your pictures, then a visit to do the work. Low Hesket is one of 438 places in Cumbria we cover. Our nearest city page is Newcastle upon Tyne, about 49 miles away.
We cover every part of the CA4 postcode area. Streets in the area include High Bell Garth, Anvil Close and Southwaite Road. Nearby, we also work in Cotehill (3 miles north), Wreay (3 miles north-west), Low Cotehill (3 miles north), Cumwhinton (4 miles north) and Carleton (4 miles north-west). Within a short drive, we also cover Carlisle (7 miles north-west), Penrith (10 miles south), Currock (6 miles north-west), Raffles (8 miles north-west), Botcherby (6 miles north-west) and Morton (7 miles north-west).
Near you in Low Hesket
We visit homes around Rose & Crown pub. For rail, the closest station is Armathwaite station, roughly 2.4 miles east. Well-known places in the area include Garlands Hospital (5.2 miles north-west) and Armathwaite Castle (2.5 miles east).
Looking after it afterwards
A little care keeps the finish looking good. We recommend:
- Clean with a soft cloth and mild detergent
- Fix dripping taps quickly
- A quick wipe after use keeps limescale away
- Keep suction mats out of the bath
Dry the bath after use if possible, especially in hard water areas, and rinse away any product left on the surface.
The longer worn enamel is left, the rougher it gets, and rust spots spread under the surface. Resurfacing sooner means less repair work first.
What a repair can’t fix
To be straight with you, there are a few things a repair will not fix:
- A bath that is rusted through
- Anything hidden under an old coating, until we remove it
- Leaks from fittings rather than the bath
Not sure? Send pictures and we’ll give you a straight answer.
Materials we repair
- Pressed steel baths
- Victorian roll-tops
- Cast iron baths
- Basins & shower trays
- Acrylic baths
Your questions about bath re-enamelling in Low Hesket
Will the new finish last?
It depends on preparation, use and care. Properly prepared and looked after, it lasts well, and it’s guaranteed for a year.
Can you do the outside of a roll-top?
Yes, often. The inside is resurfaced, and we can refinish the outside as well.
Are you a vetted contractor?
We hold CHAS, Constructionline, SafeContractor, SMAS Worksafe and Builder’s Profile accreditations.
Is there a guarantee?
Yes, for a year. If there is a problem with the work in that time, we come back and put it right.
Can you fix a peeling bath coating?
In most cases. We strip the failing coating and resurface it properly. Tell us about it when you ask for a quote.
Do you need to take the bath out?
No. We resurface it in place, so the tiles and taps stay put.
What do you need from me?
Some pictures, your postcode and how to reach you. On the day, access to the room.
Will it make a mess?
Very little mess: we sheet and mask everything nearby, and we take our waste away with us.
For landlords and businesses
Letting agents frequently send us photos straight from the inventory. You can have a price before you arrange access, and we can arrange access with the tenant directly if that helps.
We regularly work with letting and managing agents. Send the address, photos and access details.
Nearby places to Low Hesket
Also in Low Hesket
What we do, step by step
Nothing needs to be moved out of the room. We bring everything we need with us, lay protective sheets and get going once we’ve agreed what we are doing. It normally takes most of the day, and you’re welcome to carry on with your day while we work.
- We sheet, mask and ventilate the room.
- We remove the old silicone and deep clean the bath.
- Chips, rust and pitting are repaired.
- The surface is keyed and primed for the new finish.
- The new finish is sprayed on in several coats and left to cure.
Preparing for the visit
- Make sure the room can be ventilated
- Keep pets and children out of the room while we work
- Point us to the nearest place to park
How to get a price
Pricing is simple: take a close-up of the damage and a photo from further back, send them over with your postcode, and we will reply with a fixed price. There is no charge for the quote and no obligation.
Related advice
What your bath is made of matters
Cast iron
Cast iron baths are the classic candidate for re-enamelling. The body lasts for generations; only the enamel wears, so a new finish makes them look new again.
Pressed steel
Under the enamel of a steel bath is thin metal. Once a chip exposes it, rust follows quickly, so we treat and seal the metal before filling.
About our accreditations · Every repair comes with a one-year guarantee.
